WMR300: windchill/heatindex

[Miguel Iniesta]

Station: WMR300
weewx v3.6.2

Since updated to v3.6.2, I have realised that windchill/heatindex data are not available in my system.
In weewx.conf the default option for these data is prefer_harware so I understand that even a station problem would not prevent these data to be recorded.
I do not have remote access to my system right now but I do not remember having modified the value of these parameters.

Some help would be much appreciated.
Thank you.

[Andrew Milner]

Does the wm300 show values for windchill and heat index?  weewx software generated values require temp < 50F and wind > 5mph for windchill and >80F and humidity > 40% for heatindex otherwise will default to the same as outdoor temperature.

[Miguel Iniesta]

Hello Andrew,

I don’t have access to the station right now but weewx does not even default to outdoor temp.

You can have a look: www.navarredondilla.info

Thanks.

[Andrew Milner]

If you have said windchill and/or heat index are hardware generated then:

a) According to WMR300 manual the wmr300 only calculates (and so only provides) heat index when temp is > 80F and humidity > 40%

b) I do not know how/when windchill is calculated by wmr300  - manual says it is based on wind speed and temperature, and then goes on to say it is based on channel 1 temperature and humidity.  This leaves me confused 

If it does not calculate heatindex or windchill then I assume the output from the station is Null (none or n/a)

If you have said weewx should calculate windchill (software preferred) then weewx will calculate values when temp > 80, humidity > 40 or temp<50, wind > 5 - or will just set to outdoor temperature

If you have said hardware preferred then what you see will depend on what the hardware outputs, and weewx will not necessarily perform a calculation if the hardware provides a value of some sort.

Why not set windchill and heatindex to software or software preferred, and see what happens - do you then get meaningful values??

[Andrew Milner]

It is of course quite right and proper that there is not always a heat index or windchill value - and in fact you can never have both available!!!!!

[mwall]

miguel,

there was a typo in the wmr300 ConfEditor.  it used 'Calculation' instead of 'Calculations'.  as a result, the values in StdWXCalculate were not set properly.

to fix it, modify your weewx.conf to look like this:

[StdWXCalculate]
    [[Calculations]]
        rainRate = hardware
        windchill = hardware
        heatindex = hardware
        dewpoint = hardware

the wmr300 emits partial packets.  so if you tell weewx to calculate these derived values, it never will.  the hardware provides these values, so use the hardware.

the bug was fixed at commit 7d26b4f.

m

[mwall]

On Monday, February 27, 2017 at 5:49:30 AM UTC-5, Miguel Iniesta wrote:

You can have a look: www.navarredondilla.info

miguel,

that is a fascinating wind pattern - the winds shift pretty decisively at day/night boundaries!

is that a mountain/valley weather pattern?

m

[Torbjørn Aasen]

This is how mine is set up and does not work

[StdWXCalculate]

    [[Calculations]]

        # Derived quantities are calculated by this service. Possible values $

        #  hardware        - use the value provided by hardware

        #  software        - use the value calculated by weewx

        #  prefer_hardware - use value provide by hardware if available,

        #                      otherwise use value calculated by weewx

        pressure = prefer_hardware

        barometer = prefer_hardware

        altimeter = prefer_hardware

        windchill = hardware

        heatindex = hardware

        dewpoint = hardware

        inDewpoint = prefer_hardware

        rainRate = hardware

    [[Calculatios]]

[Torbjørn Aasen]

[Miguel Iniesta]

Have you reload weewx.conf or restarted weewx after updating weewx.conf?
I will have to wait al least a couple of weeks before being able to try the solution

Cheers.

[Miguel Iniesta]

Hello Matthew,

Yes, the pattern is really interesting, but it is still quite unknown to me.
There is not any other station in this high part of the valley and further down the wind does not behave like this.
Being a mountain area, I think orographic conditions might play an important role.

Thank you.

[mwall]

On Monday, February 27, 2017 at 12:24:11 PM UTC-5, Miguel Iniesta wrote:

Have you reload weewx.conf or restarted weewx after updating weewx.conf?
I will have to wait al least a couple of weeks before being able to try the solution

miguel and torbjørn,

i found another bug in the wmr300 driver.  the hardware reports both heatindex and windchill in history packets, so you should see heatindex and windchill for data read from the logger.  the hardware reports current windchill in *wind* packets, and the driver was not decoding these bytes.  also, it looks like the hardware reports current heat index in bytes 13 and 14 of D3 packets, and the driver was not decoding these bytes.

this is fixed in 0.18rc6 at commit baea414.

https://raw.githubusercontent.com/weewx/weewx/development/bin/weewx/drivers/wmr300.py

m

[Torbjørn Aasen]

Supports this also Norwegian as I have

--
You received this message because you are subscribed to a topic in the Google Groups "weewx-user" group.
To unsubscribe from this topic, visit https://groups.google.com/d/topic/weewx-user/CMhCjyOZdRk/unsubscribe.
To unsubscribe from this group and all its topics, send an email to weewx-user+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

--

 

 

 

 

Med vennlig hilsen

Torbjørn Aasen

Mob: 92092037

 

Carpe Diem

[Ruben Navarro Huedo]

Using this version:

Feb 27 20:31:06 raspberrypi weewx[3370]: engine: Caught unrecoverable exception in engine:
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****  _extract_signed() takes exactly 3 arguments (2 given)
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****  Traceback (most recent call last):
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****    File "/usr/share/weewx/weewx/engine.py", line 847, in main
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****      engine.run()
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****    File "/usr/share/weewx/weewx/engine.py", line 186, in run
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****      for packet in self.console.genLoopPackets():
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****    File "/usr/share/weewx/weewx/drivers/wmr300.py", line 887, in genLoopPackets
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****      pkt = Station.decode(buf)
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****    File "/usr/share/weewx/weewx/drivers/wmr300.py", line 1290, in decode
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****      pkt = getattr(Station, '_decode_%02x' % buf[0])(buf)
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****    File "/usr/share/weewx/weewx/drivers/wmr300.py", line 1383, in _decode_d4
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****      pkt['windchill'] = Station._extract_signed(buf[18:20], 0.1) # C
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****  TypeError: _extract_signed() takes exactly 3 arguments (2 given)
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****  Exiting.

El lunes, 27 de febrero de 2017, 20:22:36 (UTC+1), Torbjørn Aasen escribió:

Supports this also Norwegian as I have

2017-02-27 18:48 GMT+01:00 mwall <mw...@users.sourceforge.net>:

On Monday, February 27, 2017 at 12:24:11 PM UTC-5, Miguel Iniesta wrote:

Have you reload weewx.conf or restarted weewx after updating weewx.conf?
I will have to wait al least a couple of weeks before being able to try the solution

miguel and torbjørn,

i found another bug in the wmr300 driver.  the hardware reports both heatindex and windchill in history packets, so you should see heatindex and windchill for data read from the logger.  the hardware reports current windchill in *wind* packets, and the driver was not decoding these bytes.  also, it looks like the hardware reports current heat index in bytes 13 and 14 of D3 packets, and the driver was not decoding these bytes.

this is fixed in 0.18rc6 at commit baea414.

https://raw.githubusercontent.com/weewx/weewx/development/bin/weewx/drivers/wmr300.py

m

--
You received this message because you are subscribed to a topic in the Google Groups "weewx-user" group.
To unsubscribe from this topic, visit https://groups.google.com/d/topic/weewx-user/CMhCjyOZdRk/unsubscribe.

To unsubscribe from this group and all its topics, send an email to weewx-user+...@googlegroups.com.

For more options, visit https://groups.google.com/d/optout.

[mwall]

On Monday, February 27, 2017 at 2:52:08 PM UTC-5, Ruben Navarro Huedo wrote:

Using this version:

Feb 27 20:31:06 raspberrypi weewx[3370]: engine: Caught unrecoverable exception in engine:
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****  _extract_signed() takes exactly 3 arguments (2 given)
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****  Traceback (most recent call last):
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****    File "/usr/share/weewx/weewx/engine.py", line 847, in main
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****      engine.run()
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****    File "/usr/share/weewx/weewx/engine.py", line 186, in run
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****      for packet in self.console.genLoopPackets():
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****    File "/usr/share/weewx/weewx/drivers/wmr300.py", line 887, in genLoopPackets
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****      pkt = Station.decode(buf)
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****    File "/usr/share/weewx/weewx/drivers/wmr300.py", line 1290, in decode
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****      pkt = getattr(Station, '_decode_%02x' % buf[0])(buf)
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****    File "/usr/share/weewx/weewx/drivers/wmr300.py", line 1383, in _decode_d4
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****      pkt['windchill'] = Station._extract_signed(buf[18:20], 0.1) # C
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****  TypeError: _extract_signed() takes exactly 3 arguments (2 given)
Feb 27 20:31:06 raspberrypi weewx[3370]:     ****  Exiting.

sorry.  try downloading again.  now at 0.18rc7

m

[Torbjørn Aasen]

Done this: 

pi@RPi_hjemme:~ $ wget -O wmr300-0.18rc7.py https://raw.githubusercontent.com/weewx/weewx/development/bin/weewx/drivers/wmr300.py

--2017-02-28 08:10:40--  https://raw.githubusercontent.com/weewx/weewx/development/bin/weewx/drivers/wmr300.py

Resolving raw.githubusercontent.com (raw.githubusercontent.com)... 151.101.84.133

Connecting to raw.githubusercontent.com (raw.githubusercontent.com)|151.101.84.133|:443... connected.

HTTP forespřrsel sendt, mottar topptekster... 200 OK

Lengde: 46209 (45K) [text/plain]

Saving to: ‘wmr300-0.18rc7.py’

wmr300-0.18rc7.py   100%[=====================>]  45,13K  --.-KB/s   in 0,03s   

2017-02-28 08:10:40 (1,46 MB/s) - ‘wmr300-0.18rc7.py’ saved [46209/46209]

pi@RPi_hjemme:~ $ sudo cp wmr300-0.18rc7.py /usr/share/weewx/weewx/drivers/wmr300.py

pi@RPi_hjemme:~ $

pi@RPi_hjemme:~ $ tail -f /var/log/syslog

Feb 28 08:01:13 RPi_hjemme weewx[10266]: wmr300: request station status: 322 (42)

Feb 28 08:01:14 RPi_hjemme systemd[1]: Stopping LSB: weewx weather system...

Feb 28 08:01:14 RPi_hjemme weewx[10266]: engine: Received signal TERM.

Feb 28 08:01:14 RPi_hjemme weewx[10266]: engine: Main loop exiting. Shutting engine down.

Feb 28 08:01:14 RPi_hjemme weewx[10266]: engine: Shutting down StdReport thread

Feb 28 08:01:14 RPi_hjemme weewx[10266]: engine: StdReport thread has been terminated

Feb 28 08:01:14 RPi_hjemme weewx[10266]: restx: Shut down Wunderground-PWS thread.

Feb 28 08:01:14 RPi_hjemme weewx[10266]: engine: Terminating weewx version 3.6.2

Feb 28 08:01:19 RPi_hjemme weewx[18416]: Stopping weewx weather system: weewx..

Feb 28 08:01:19 RPi_hjemme systemd[1]: Stopped LSB: weewx weather system.

Feb 28 08:12:45 RPi_hjemme rsyslogd-2007: action 'action 17' suspended, next retry is Tue Feb 28 08:14:15 2017 [try http://www.rsyslog.com/e/2007 ]

Feb 28 08:13:02 RPi_hjemme wpa_supplicant[487]: wlan0: WPA: Group rekeying completed with 00:22:07:4a:eb:cb [GTK=CCMP]

Feb 28 08:13:18 RPi_hjemme systemd[1]: Starting LSB: weewx weather system...

Feb 28 08:13:19 RPi_hjemme weewx[18538]: engine: Initializing weewx version 3.6.2

Feb 28 08:13:19 RPi_hjemme weewx[18538]: engine: Using Python 2.7.9 (default, Sep 17 2016, 20:26:04) #012[GCC 4.9.2]

Feb 28 08:13:19 RPi_hjemme weewx[18538]: engine: Platform Linux-4.4.34-v7+-armv7l-with-debian-8.0

Feb 28 08:13:19 RPi_hjemme weewx[18538]: engine: pid file is /var/run/weewx.pid

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Using configuration file /etc/weewx/weewx.conf

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Initializing engine

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Loading station type WMR300 (weewx.drivers.wmr300)

Feb 28 08:13:19 RPi_hjemme weewx[18527]: Starting weewx weather system: weewx.

Feb 28 08:13:19 RPi_hjemme systemd[1]: Started LSB: weewx weather system.

Feb 28 08:13:19 RPi_hjemme weewx[18542]: wmr300: driver version is 0.18rc7

Feb 28 08:13:19 RPi_hjemme weewx[18542]: wmr300: usb info: pyusb_version=0.4.x

Feb 28 08:13:19 RPi_hjemme weewx[18542]: wmr300: sensor map is {'outHumidity': 'humidity_1', 'extraDewpoint6': 'dewpoint_7', 'windchill': 'windchill', 'extraDewpoint4': 'dewpoint_5', 'rainRate': 'rain_rate', 'heatindex': 'heatindex_1', 'inTemp': 'temperature_0', 'windGustDir': 'wind_gust_dir', 'extraDewpoint2': 'dewpoint_3', 'extraDewpoint3': 'dewpoint_4', 'extraDewpoint1': 'dewpoint_2', 'barometer': 'barometer', 'extraDewpoint7': 'dewpoint_8', 'dewpoint': 'dewpoint_1', 'extraDewpoint5': 'dewpoint_6', 'extraHumid6': 'humidity_7', 'pressure': 'pressure', 'extraHumid4': 'humidity_5', 'extraHumid5': 'humidity_6', 'extraHumid2': 'humidity_3', 'extraHumid3': 'humidity_4', 'extraHumid1': 'humidity_2', 'extraTemp6': 'temperature_7', 'extraTemp7': 'temperature_8', 'extraTemp4': 'temperature_5', 'extraTemp5': 'temperature_6', 'extraTemp2': 'temperature_3', 'extraTemp3': 'temperature_4', 'extraTemp1': 'temperature_2', 'extraHeatindex3': 'heatindex_4', 'extraHeatindex2': 'heatindex_3', 'extraHeatindex1': 'heatindex_2', 'extraHeatindex7': 'heatindex_8', 'extraHeatindex6': 'heatindex_7', 'extraHeatindex5': 'heatindex_6', 'extraHumid7': 'humidity_8', 'extraHeatindex4': 'heatindex_5', 'windDir': 'wind_dir', 'outTemp': 'temperature_1', 'windSpeed': 'wind_avg', 'inHumidity': 'humidity_0', 'windGust': 'wind_gust'}

Feb 28 08:13:19 RPi_hjemme weewx[18542]: wmr300: Found station at bus=001 device=006

Feb 28 08:13:19 RPi_hjemme kernel: [157749.618835] usb 1-1.5: reset full-speed USB device number 6 using dwc_otg

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Loading service weewx.engine.StdTimeSynch

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Finished loading service weewx.engine.StdTimeSynch

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Loading service weewx.engine.StdConvert

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: StdConvert target unit is 0x1

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Finished loading service weewx.engine.StdConvert

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Loading service weewx.engine.StdCalibrate

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Finished loading service weewx.engine.StdCalibrate

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Loading service weewx.engine.StdQC

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Finished loading service weewx.engine.StdQC

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Loading service weewx.wxservices.StdWXCalculate

Feb 28 08:13:19 RPi_hjemme weewx[18542]: wxcalculate: The following values will be calculated: barometer=prefer_hardware, windchill=hardware, dewpoint=hardware, appTemp=prefer_hardware, rainRate=hardware, windrun=prefer_hardware, heatindex=hardware, maxSolarRad=prefer_hardware, humidex=prefer_hardware, pressure=prefer_hardware, inDewpoint=prefer_hardware, ET=prefer_hardware, altimeter=prefer_hardware, cloudbase=prefer_hardware

Feb 28 08:13:19 RPi_hjemme weewx[18542]: wxcalculate: The following algorithms will be used for calculations: altimeter=aaNOAA, maxSolarRad=RS

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Finished loading service weewx.wxservices.StdWXCalculate

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Loading service weewx.engine.StdArchive

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Archive will use data binding wx_binding

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Record generation will be attempted in 'hardware'

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Using archive interval of 300 seconds (specified in weewx configuration)

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Use LOOP data in hi/low calculations: 1

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Using binding 'wx_binding' to database 'weewx.sdb'

Feb 28 08:13:19 RPi_hjemme weewx[18542]: manager: Starting backfill of daily summaries

Feb 28 08:13:19 RPi_hjemme weewx[18542]: manager: Daily summaries up to date

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Finished loading service weewx.engine.StdArchive

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Loading service weewx.restx.StdStationRegistry

Feb 28 08:13:19 RPi_hjemme weewx[18542]: restx: StationRegistry: Registration not requested.

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Finished loading service weewx.restx.StdStationRegistry

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Loading service weewx.restx.StdWunderground

Feb 28 08:13:19 RPi_hjemme weewx[18542]: restx: Wunderground-PWS: Data for station IBUSKERU76 will be posted

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Finished loading service weewx.restx.StdWunderground

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Loading service weewx.restx.StdPWSweather

Feb 28 08:13:19 RPi_hjemme weewx[18542]: restx: PWSweather: Posting not enabled.

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Finished loading service weewx.restx.StdPWSweather

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Loading service weewx.restx.StdCWOP

Feb 28 08:13:19 RPi_hjemme weewx[18542]: restx: CWOP: Posting not enabled.

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Finished loading service weewx.restx.StdCWOP

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Loading service weewx.restx.StdWOW

Feb 28 08:13:19 RPi_hjemme weewx[18542]: restx: WOW: Posting not enabled.

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Finished loading service weewx.restx.StdWOW

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Loading service weewx.restx.StdAWEKAS

Feb 28 08:13:19 RPi_hjemme weewx[18542]: restx: AWEKAS: Posting not enabled.

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Finished loading service weewx.restx.StdAWEKAS

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Loading service weewx.engine.StdPrint

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Finished loading service weewx.engine.StdPrint

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Loading service weewx.engine.StdReport

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Finished loading service weewx.engine.StdReport

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Starting up weewx version 3.6.2

Feb 28 08:13:19 RPi_hjemme weewx[18542]: engine: Station does not support reading the time

Feb 28 08:13:19 RPi_hjemme weewx[18542]: wmr300: reading records since 2017-02-28 08:00:00 CET (1488265200)

Feb 28 08:13:19 RPi_hjemme weewx[18542]: wmr300: request station status: 0 (00)

Feb 28 08:13:19 RPi_hjemme weewx[18542]: wmr300: initiate record request: 0 (00)

Feb 28 08:13:19 RPi_hjemme weewx[18542]: wmr300: catchup in progress: count=0 last_index=0 latest_index=369

Feb 28 08:13:19 RPi_hjemme weewx[18542]: wmr300: initiate record request: 0 (00)

Feb 28 08:13:19 RPi_hjemme weewx[18542]: wmr300: request records starting with 32

Feb 28 08:13:20 RPi_hjemme weewx[18542]: wmr300: possible missed rain event: new=12.446 old=None

Feb 28 08:13:20 RPi_hjemme weewx[18542]: wmr300: rain=None rain_total=12.446 last_rain=None

Feb 28 08:13:39 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:13:39 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:13:39 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:13:40 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:13:40 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:13:40 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:13:40 RPi_hjemme weewx[18542]: wmr300: catchup complete: count=0 last_index=368 latest_index=369

Feb 28 08:13:40 RPi_hjemme weewx[18542]: engine: Starting main packet loop.

Feb 28 08:14:00 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:14:20 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:14:20 RPi_hjemme rsyslogd-2007: action 'action 17' suspended, next retry is Tue Feb 28 08:15:50 2017 [try http://www.rsyslog.com/e/2007 ]

Feb 28 08:14:40 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:15:00 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:15:24 RPi_hjemme weewx[18542]: manager: added record 2017-02-28 08:15:00 CET (1488266100) to database 'weewx.sdb'

Feb 28 08:15:24 RPi_hjemme weewx[18542]: manager: added record 2017-02-28 08:15:00 CET (1488266100) to daily summary in 'weewx.sdb'

Feb 28 08:15:26 RPi_hjemme weewx[18542]: reportengine: Running reports for latest time in the database.

Feb 28 08:15:26 RPi_hjemme weewx[18542]: reportengine: Running report StandardReport

Feb 28 08:15:26 RPi_hjemme weewx[18542]: reportengine: Found configuration file /etc/weewx/skins/Standard/skin.conf for report StandardReport

Feb 28 08:15:26 RPi_hjemme weewx[18542]: cheetahgenerator: using search list ['weewx.cheetahgenerator.Almanac', 'weewx.cheetahgenerator.Station', 'weewx.cheetahgenerator.Stats', 'weewx.cheetahgenerator.UnitInfo', 'weewx.cheetahgenerator.Extras']

Feb 28 08:15:26 RPi_hjemme weewx[18542]: restx: Wunderground-PWS: Published record 2017-02-28 08:15:00 CET (1488266100)

Feb 28 08:15:26 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:15:30 RPi_hjemme weewx[18542]: cheetahgenerator: Generated 14 files for report StandardReport in 3.89 seconds

Feb 28 08:15:31 RPi_hjemme weewx[18542]: genimages: Generated 12 images for StandardReport in 0.84 seconds

Feb 28 08:15:31 RPi_hjemme weewx[18542]: reportengine: copied 9 files to /var/www/html/weewx

Feb 28 08:15:31 RPi_hjemme weewx[18542]: reportengine: Running report FTP

Feb 28 08:15:31 RPi_hjemme weewx[18542]: reportengine: Found configuration file /etc/weewx/skins/Ftp/skin.conf for report FTP

Feb 28 08:15:31 RPi_hjemme weewx[18542]: reportengine: FTP upload not requested. Skipped.

Feb 28 08:15:31 RPi_hjemme weewx[18542]: reportengine: Running report RSYNC

Feb 28 08:15:31 RPi_hjemme weewx[18542]: reportengine: Found configuration file /etc/weewx/skins/Rsync/skin.conf for report RSYNC

Feb 28 08:15:31 RPi_hjemme weewx[18542]: reportengine: rsync upload not requested. Skipped.

Feb 28 08:15:46 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:16:06 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:16:06 RPi_hjemme rsyslogd-2007: action 'action 17' suspended, next retry is Tue Feb 28 08:17:36 2017 [try http://www.rsyslog.com/e/2007 ]

Feb 28 08:16:24 RPi_hjemme weewx[18542]: wmr300: rain=0.508 rain_total=12.954 last_rain=12.446

Feb 28 08:16:27 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:16:47 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:16:47 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:16:47 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:16:47 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:16:48 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:17:01 RPi_hjemme CRON[18626]: (root) CMD (   cd / && run-parts --report /etc/cron.hourly)

Feb 28 08:17:08 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:17:28 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:17:48 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:17:48 RPi_hjemme rsyslogd-2007: action 'action 17' suspended, next retry is Tue Feb 28 08:19:18 2017 [try http://www.rsyslog.com/e/2007 ]

Feb 28 08:18:08 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:18:28 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:18:48 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:19:08 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:19:28 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:19:28 RPi_hjemme rsyslogd-2007: action 'action 17' suspended, next retry is Tue Feb 28 08:20:58 2017 [try http://www.rsyslog.com/e/2007 ]

Feb 28 08:19:48 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:20:08 RPi_hjemme weewx[18542]: wmr300: request station status: 368 (70)

Feb 28 08:20:17 RPi_hjemme weewx[18542]: manager: added record 2017-02-28 08:20:00 CET (1488266400) to database 'weewx.sdb'

Feb 28 08:20:17 RPi_hjemme weewx[18542]: manager: added record 2017-02-28 08:20:00 CET (1488266400) to daily summary in 'weewx.sdb'

Feb 28 08:20:19 RPi_hjemme weewx[18542]: reportengine: Running reports for latest time in the database.

Feb 28 08:20:19 RPi_hjemme weewx[18542]: reportengine: Running report StandardReport

Feb 28 08:20:19 RPi_hjemme weewx[18542]: reportengine: Found configuration file /etc/weewx/skins/Standard/skin.conf for report StandardReport

Feb 28 08:20:19 RPi_hjemme weewx[18542]: cheetahgenerator: using search list ['weewx.cheetahgenerator.Almanac', 'weewx.cheetahgenerator.Station', 'weewx.cheetahgenerator.Stats', 'weewx.cheetahgenerator.UnitInfo', 'weewx.cheetahgenerator.Extras']

Feb 28 08:20:19 RPi_hjemme weewx[18542]: restx: Wunderground-PWS: Published record 2017-02-28 08:20:00 CET (1488266400)

Feb 28 08:20:20 RPi_hjemme weewx[18542]: cheetahgenerator: Generated 14 files for report StandardReport in 1.20 seconds

Feb 28 08:20:21 RPi_hjemme weewx[18542]: genimages: Generated 12 images for StandardReport in 0.83 seconds

Feb 28 08:20:21 RPi_hjemme weewx[18542]: reportengine: copied 0 files to /var/www/html/weewx

Feb 28 08:20:21 RPi_hjemme weewx[18542]: reportengine: Running report FTP

Feb 28 08:20:21 RPi_hjemme weewx[18542]: reportengine: Found configuration file /etc/weewx/skins/Ftp/skin.conf for report FTP

Feb 28 08:20:21 RPi_hjemme weewx[18542]: reportengine: FTP upload not requested. Skipped.

Feb 28 08:20:21 RPi_hjemme weewx[18542]: reportengine: Running report RSYNC

Feb 28 08:20:21 RPi_hjemme weewx[18542]: reportengine: Found configuration file /etc/weewx/skins/Rsync/skin.conf for report RSYNC

Feb 28 08:20:21 RPi_hjemme weewx[18542]: reportengine: rsync upload not requested. Skipped.

^C

pi@RPi_hjemme:~ $ 

--

You received this message because you are subscribed to a topic in the Google Groups "weewx-user" group.
To unsubscribe from this topic, visit https://groups.google.com/d/topic/weewx-user/CMhCjyOZdRk/unsubscribe.

To unsubscribe from this group and all its topics, send an email to weewx-user+unsubscribe@googlegroups.com.

For more options, visit https://groups.google.com/d/optout.

[Torbjørn Aasen]

it works well now I think.

you can take a look.....

http://olga.no/ver 

[Miguel Iniesta]

Prefect.

Thank you.

To unsubscribe from this group and all its topics, send an email to weewx-user+...@googlegroups.com.

For more options, visit https://groups.google.com/d/optout.

--

 

 

 

 

Med vennlig hilsen

Torbjørn Aasen

Mob: 92092037

 

Carpe Diem

[Ruben Navarro Huedo]

Last version running fine here.