EN 10204 Type certificate

[vk]

Gents,

Manufacturer has issued MTC fulfilling all the requirements as mentioned in EN 10204 3.1.

But nowhere it mentions as "EN 10204 Type 3.1"

Can this be considered or do they have to mention that it complies with the requirements of EN 10204 Type3.1"

Regards

Vivek

[Rajnish Dixit]

Hi Vivek,

Please check that the certificate should be independently endorsed by manufacturer's Quality department. It is also to be declared by manufacturer that requirement of 3.1 has been fulfilled by mentioning the same (EN 10204 3.1) on certificate.

Hope, it is clear.

Thanks,
Warm Regards,

Rajnish Dixit

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-weld...@googlegroups.com.
Visit this group at https://groups.google.com/group/materials-welding.
For more options, visit https://groups.google.com/d/optout.

[Mohamed Muneeb]

Who is the owner representative here?

Does the owners spec has a requirement for procurement? 

Please follow as per that, none of the MTCs are entertained or accepted without inspection certification types, regardless of various types.

Thanks 

Muneeb

[Dinesh Somwanshi]

Dear.

If manufacturer doesnt shown certificate type 3.1 then by doing check test to confirm 3.1 is acceptable.

Regards

Dinesh

--

https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.

To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.

[patelr...@gmail.com]

Please anybody says that it is possible to get delt ferrite less than 1.5 % in SA 105, SA 182 F11 & SA 182 F22 Material.

[Prakash Hegde]

Hi!

Delta ferrite you can measure in SS overlay or weld and not in CS LAS weld

Regards

Hegde

Sent from Yahoo Mail on Android

On Sat, 12 Jan 2019 at 20:40, patelr...@gmail.com

<patelr...@gmail.com> wrote:

Please anybody says that it is possible to get delt ferrite less than 1.5 % in SA 105, SA 182 F11 & SA 182 F22 Material.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.

To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsub...@googlegroups.com.

[sunil kaushik]

Dear sir,

                Suppose someone purchase water quench material then is it possible?

Sunil kaushik,

Welding Engineer

To unsubscribe from this group and stop receiving emails from it, send an email to materials-weld...@googlegroups.com.

[Roshan Patel]

I am talking about raw material forging not in welding. 

My customer's requirement is micrographic examination carried out using replica method and confirm that material is pure tempered martensite and delta ferrite less than 1.5 %. 

We have to supply them SA105, SA 182 F11, SA 182 F22, SA 182 F91, SA 182 F92, DIN 1.4923, DIN 1.4122.

My question is that in which material from above customer's requirement is applicable? 

You received this message because you are subscribed to a topic in the Google Groups "Materials & Welding" group.
To unsubscribe from this topic, visit https://groups.google.com/d/topic/materials-welding/IF-Tq2Vr9fM/unsubscribe.
To unsubscribe from this group and all its topics, send an email to materials-weld...@googlegroups.com.

[rajesh kaswala]

only this grade   SA 182 F91, SA 182 F92, DIN 1.4923, DIN 1.4122. 

regard

rajesh