DNS-323 Not Showing Up on Network (Log File Attached)

[SCARNG]

Replaced drives in DNS-323 and now cannot see DNS-323 on network anymore.   Using flashed Alt-F firmware.  I have tried both  DNS-323 as static IP via rooter and DHCP, I get nothing on the network (currently static IP).  The network icon (bottom row center icon) is blinking rapidly and then pulses and then rapidly.  I have place back the old drives to see if that would help- what was I thinking I've flashed the rom, right!

I should be able to see the device on the network at least, right?

I still cannot see it on the network, any help or have I a bricked DNS-323?

[SCARNG]

I was able to mount the drive using ExT2Fsd and pull the alt-f.log file.  Alt-F is running - I'm posting the log but have replace the MAX address with XX:XX:XX:XX:XX:XX  

====================== Alt-F 0.1RC3 ======================

Sun Jul 21 14:31:54 NONE 2013

====================== BOARD ======================

A1

====================== Flashed Firmware ======================

Alt-F-0.1RC3, kernel 2.6.35.14

====================== DMESG ======================

Linux version 2.6.35.14 (jcard@silver) (gcc version 4.3.3 (GCC) ) #1 Sun Mar 17 19:51:52 WET 2013

CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=a0053177

CPU: VIVT data cache, VIVT instruction cache

Machine: D-Link DNS-321/323

Clearing invalid memory bank 0KB@0xffffffff

Clearing invalid memory bank 0KB@0xffffffff

Clearing invalid memory bank 0KB@0xffffffff

Ignoring unrecognised tag 0x00000000

Ignoring unrecognised tag 0x00000000

Ignoring unrecognised tag 0x00000000

Ignoring unrecognised tag 0x41000403

Memory policy: ECC disabled, Data cache writeback

On node 0 totalpages: 16384

free_area_init_node: node 0, pgdat c0381bd0, node_mem_map c0397000

  Normal zone: 128 pages used for memmap

  Normal zone: 0 pages reserved

  Normal zone: 16256 pages, LIFO batch:3

Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256

Kernel command line: root=/dev/ram console=ttyS0,115200 :::DB88FXX81:egiga0:none console=ttyS0,115200 root=/dev/ram0 init=/init

PID hash table entries: 256 (order: -2, 1024 bytes)

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory: 64MB = 64MB total

Memory: 55064k/55064k available, 10472k reserved, 0K highmem

Virtual kernel memory layout:

    vector  : 0xffff0000 - 0xffff1000   (   4 kB)

    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)

    DMA     : 0xffc00000 - 0xffe00000   (   2 MB)

    vmalloc : 0xc4800000 - 0xfd800000   ( 912 MB)

    lowmem  : 0xc0000000 - 0xc4000000   (  64 MB)

    modules : 0xbf000000 - 0xc0000000   (  16 MB)

      .init : 0xc0008000 - 0xc0029000   ( 132 kB)

      .text : 0xc0029000 - 0xc0350000   (3228 kB)

      .data : 0xc036a000 - 0xc03821e0   (  97 kB)

NR_IRQS:64

Calibrating delay loop... 332.59 BogoMIPS (lpj=1662976)

pid_max: default: 4096 minimum: 301

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

NET: Registered protocol family 16

Orion ID: MV88F5181-Rev-B1. TCLK=166666667.

DNS-321/323: Identified HW revision A1

DNS-321/323: Found ethernet MAC address: XX:XX:XX:XX:XX:XX.

Applying Orion-1/Orion-NAS PCIe config read transaction workaround

pci 0000:00:00.0: reg 10: [mem 0xf1000000-0xf10fffff 64bit pref]

pci 0000:00:00.0: reg 18: [mem 0x00000000-0x03ffffff]

pci 0000:00:01.0: reg 10: [mem 0x40000000-0x400fffff 64bit]

pci 0000:00:01.0: reg 18: [io  0xf0000000-0xf00000ff]

PCI: bus0: Fast back to back transfers disabled

pci 0000:01:00.0: reg 10: [mem 0x00000000-0x03ffffff 64bit pref]

pci 0000:01:00.0: reg 18: [mem 0x10000000-0x1fffffff 64bit pref]

pci 0000:01:00.0: reg 20: [mem 0xf1000000-0xf10fffff 64bit]

pci 0000:01:00.0: reg 30: [mem 0xe0000000-0xe7ffffff pref]

pci 0000:01:00.0: supports D1 D2

pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot

pci 0000:01:00.0: PME# disabled

PCI: bus1: Fast back to back transfers enabled

pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe00fffff 64bit]

pci 0000:00:01.0: BAR 0: set to [mem 0xe0000000-0xe00fffff 64bit] (PCI address [0xe0000000-0xe00fffff]

pci 0000:00:01.0: BAR 2: assigned [io  0x1000-0x10ff]

pci 0000:00:01.0: BAR 2: set to [io  0x1000-0x10ff] (PCI address [0x1000-0x10ff]

bio: create slab <bio-0> at 0

SCSI subsystem initialized

libata version 3.00 loaded.

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

Switching to clocksource orion_clocksource

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 2048 (order: 2, 16384 bytes)

TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

TCP: Hash tables configured (established 2048 bind 2048)

TCP reno registered

NET: Registered protocol family 1

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

RPC: Registered tcp NFSv4.1 backchannel transport module.

PCI: CLS 32 bytes, default 32

Trying to unpack rootfs image as initramfs...

rootfs image is not initramfs (junk in compressed archive); looks like an initrd

Freeing initrd memory: 6236K

VFS: Disk quotas dquot_6.5.2

Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

squashfs: version 4.0 (2009/01/31) Phillip Lougher

Installing knfsd (copyright (C) 1996 ok...@monad.swb.de).

aufs 2-standalone.tree-35-20100809

msgmni has been set to 119

io scheduler noop registered

io scheduler deadline registered

io scheduler cfq registered (default)

Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled

serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A

console [ttyS0] enabled

brd: module loaded

loop: module loaded

sata_mv 0000:00:01.0: version 1.28

sata_mv 0000:00:01.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx

scsi0 : sata_mv

scsi1 : sata_mv

scsi2 : sata_mv

scsi3 : sata_mv

ata1: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0022000 irq 11

ata2: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0024000 irq 11

ata3: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0026000 irq 11

ata4: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0028000 irq 11

physmap platform flash device: 00800000 at f4000000

physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank

Amd/Fujitsu Extended Query Table at 0x0040

number of CFI chips: 1

cmdlinepart partition parsing not available

RedBoot partition parsing not available

Using physmap partition information

Creating 5 MTD partitions on "physmap-flash.0":

0x000000000000-0x000000010000 : "MTD1"

0x000000010000-0x000000020000 : "MTD2"

0x000000020000-0x0000001a0000 : "Linux Kernel"

0x0000001a0000-0x0000007d0000 : "File System"

0x0000007d0000-0x000000800000 : "u-boot"

MV-643xx 10/100/1000 ethernet driver version 1.4

mv643xx_eth smi: probed

net eth0: port 0 with MAC address XX:XX:XX:XX:XX:XX

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

orion-ehci orion-ehci.0: Marvell Orion EHCI

orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1

orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000

orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 1 port detected

Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

input: gpio-keys as /class/input/input0

i2c /dev entries driver

rtc-m41t80 0-0068: chip found, driver version 0.05

rtc-m41t80 0-0068: rtc core: registered m41t80 as rtc0

lm75 0-0048: hwmon1: sensor 'lm75'

md: linear personality registered for level -1

md: raid1 personality registered for level 1

Registered led device: power:blue

Registered led device: right:amber

Registered led device: left:amber

usbcore: registered new interface driver usbhid

usbhid: USB HID core driver

TCP cubic registered

NET: Registered protocol family 17

rtc-m41t80 0-0068: setting system clock to 2013-07-21 14:31:21 UTC (1374417081)

ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)

ata1.00: ATA-7: WDC WD5000YS-01MPB1, 09.02E09, max UDMA/133

ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)

ata1.00: configured for UDMA/133

scsi 0:0:0:0: Direct-Access     ATA      WDC WD5000YS-01M 09.0 PQ: 0 ANSI: 5

sd 0:0:0:0: Attached scsi generic sg0 type 0

sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)

sd 0:0:0:0: [sda] Write Protect is off

sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00

sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

 sda: sda1 sda2 sda4

sd 0:0:0:0: [sda] Attached SCSI disk

ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)

ata2.00: ATA-7: WDC WD5000KS-60MNB0, 08.02E08, max UDMA/100

ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)

ata2.00: configured for UDMA/100

scsi 1:0:0:0: Direct-Access     ATA      WDC WD5000KS-60M 08.0 PQ: 0 ANSI: 5

sd 1:0:0:0: Attached scsi generic sg1 type 0

sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB)

sd 1:0:0:0: [sdb] Write Protect is off

sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00

sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

 sdb: sdb1 sdb2 sdb4

sd 1:0:0:0: [sdb] Attached SCSI disk

ata3: SATA link down (SStatus 0 SControl 300)

ata4: SATA link down (SStatus 0 SControl 300)

md: Skipping autodetection of RAID arrays. (raid=autodetect will force)

RAMDISK: squashfs filesystem found at block 0

RAMDISK: Loading 6233KiB [1 disk] into ram disk... | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / done.

VFS: Mounted root (squashfs filesystem) readonly on device 1:0.

Freeing init memory: 132K

Adding 530108k swap on /dev/sda1.  Priority:1 extents:1 across:530108k 

md: bind<sda2>

EXT3-fs: barriers not enabled

kjournald starting.  Commit interval 5 seconds

Adding 530108k swap on /dev/sdb1.  Priority:1 extents:1 across:530108k 

EXT3-fs (sda4): using internal journal

EXT3-fs (sda4): mounted filesystem with ordered data mode

md: bind<sdb2>

md/raid1:md0: active with 2 out of 2 mirrors

md0: detected capacity change from 0 to 498215419904

 md0: unknown partition table

EXT3-fs: barriers not enabled

kjournald starting.  Commit interval 5 seconds

EXT3-fs (md0): using internal journal

EXT3-fs (md0): mounted filesystem with ordered data mode

usbcore: registered new interface driver usblp

EXT3-fs: barriers not enabled

kjournald starting.  Commit interval 5 seconds

EXT3-fs (sdb4): using internal journal

EXT3-fs (sdb4): mounted filesystem with ordered data mode

====================== SYSLOG ======================

Jul 21 14:31:38 DNS-323 syslog.info syslogd started: BusyBox v1.20.2

Jul 21 14:31:38 DNS-323 user.notice hot: Finish fscking md0: fsck 1.41.14 (22-Dec-2010) /dev/md0: clean, 18421/30408704 files, 2763678/121634624 blocks

Jul 21 14:31:38 DNS-323 user.notice kernel: klogd started: BusyBox v1.20.2 (2013-03-17 19:50:30 WET)

Jul 21 14:31:38 DNS-323 user.notice kernel: Linux version 2.6.35.14 (jcard@silver) (gcc version 4.3.3 (GCC) ) #1 Sun Mar 17 19:51:52 WET 2013

Jul 21 14:31:38 DNS-323 user.warn kernel: CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=a0053177

Jul 21 14:31:38 DNS-323 user.warn kernel: CPU: VIVT data cache, VIVT instruction cache

Jul 21 14:31:38 DNS-323 user.warn kernel: Machine: D-Link DNS-321/323

Jul 21 14:31:38 DNS-323 user.warn kernel: Clearing invalid memory bank 0KB@0xffffffff

Jul 21 14:31:38 DNS-323 user.warn kernel: Ignoring unrecognised tag 0x00000000

Jul 21 14:31:38 DNS-323 user.notice root: Starting syslogd: OK. Starting klogd: OK.

Jul 21 14:31:38 DNS-323 user.warn kernel: Ignoring unrecognised tag 0x00000000

Jul 21 14:31:38 DNS-323 user.warn kernel: Ignoring unrecognised tag 0x41000403

Jul 21 14:31:38 DNS-323 user.warn kernel: Memory policy: ECC disabled, Data cache writeback

Jul 21 14:31:38 DNS-323 user.debug kernel: On node 0 totalpages: 16384

Jul 21 14:31:38 DNS-323 user.debug kernel: free_area_init_node: node 0, pgdat c0381bd0, node_mem_map c0397000

Jul 21 14:31:38 DNS-323 user.debug kernel:   Normal zone: 128 pages used for memmap

Jul 21 14:31:38 DNS-323 user.debug kernel:   Normal zone: 0 pages reserved

Jul 21 14:31:38 DNS-323 user.debug kernel:   Normal zone: 16256 pages, LIFO batch:3

Jul 21 14:31:38 DNS-323 user.warn kernel: Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256

Jul 21 14:31:38 DNS-323 user.notice kernel: Kernel command line: root=/dev/ram console=ttyS0,115200 :::DB88FXX81:egiga0:none console=ttyS0,115200 root=/dev/ram0 init=/init

Jul 21 14:31:38 DNS-323 user.info kernel: PID hash table entries: 256 (order: -2, 1024 bytes)

Jul 21 14:31:38 DNS-323 user.info kernel: Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Jul 21 14:31:38 DNS-323 user.info kernel: Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Jul 21 14:31:38 DNS-323 user.info kernel: Memory: 64MB = 64MB total

Jul 21 14:31:38 DNS-323 user.notice kernel: Memory: 55064k/55064k available, 10472k reserved, 0K highmem

Jul 21 14:31:38 DNS-323 user.notice kernel: Virtual kernel memory layout:

Jul 21 14:31:38 DNS-323 user.notice kernel:     vector  : 0xffff0000 - 0xffff1000   (   4 kB)

Jul 21 14:31:38 DNS-323 user.notice kernel:     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)

Jul 21 14:31:38 DNS-323 user.notice kernel:     DMA     : 0xffc00000 - 0xffe00000   (   2 MB)

Jul 21 14:31:38 DNS-323 user.notice kernel:     vmalloc : 0xc4800000 - 0xfd800000   ( 912 MB)

Jul 21 14:31:38 DNS-323 user.notice kernel:     lowmem  : 0xc0000000 - 0xc4000000   (  64 MB)

Jul 21 14:31:38 DNS-323 user.notice kernel:     modules : 0xbf000000 - 0xc0000000   (  16 MB)

Jul 21 14:31:38 DNS-323 user.notice kernel:       .init : 0xc0008000 - 0xc0029000   ( 132 kB)

Jul 21 14:31:38 DNS-323 user.notice kernel:       .text : 0xc0029000 - 0xc0350000   (3228 kB)

Jul 21 14:31:38 DNS-323 user.notice kernel:       .data : 0xc036a000 - 0xc03821e0   (  97 kB)

Jul 21 14:31:38 DNS-323 user.info kernel: NR_IRQS:64

Jul 21 14:31:38 DNS-323 user.info kernel: Calibrating delay loop... 332.59 BogoMIPS (lpj=1662976)

Jul 21 14:31:38 DNS-323 user.info kernel: pid_max: default: 4096 minimum: 301

Jul 21 14:31:38 DNS-323 user.warn kernel: Mount-cache hash table entries: 512

Jul 21 14:31:38 DNS-323 user.info kernel: CPU: Testing write buffer coherency: ok

Jul 21 14:31:38 DNS-323 user.info kernel: NET: Registered protocol family 16

Jul 21 14:31:38 DNS-323 user.info kernel: Orion ID: MV88F5181-Rev-B1. TCLK=166666667.

Jul 21 14:31:38 DNS-323 user.info kernel: DNS-321/323: Identified HW revision A1

Jul 21 14:31:38 DNS-323 user.warn kernel: DNS-321/323: Found ethernet MAC address: XX:XX:XX:XX:XX:XX.

Jul 21 14:31:38 DNS-323 user.notice kernel: Applying Orion-1/Orion-NAS PCIe config read transaction workaround

Jul 21 14:31:38 DNS-323 user.debug kernel: pci 0000:00:00.0: reg 10: [mem 0xf1000000-0xf10fffff 64bit pref]

Jul 21 14:31:38 DNS-323 user.debug kernel: pci 0000:00:00.0: reg 18: [mem 0x00000000-0x03ffffff]

Jul 21 14:31:38 DNS-323 user.debug kernel: pci 0000:00:01.0: reg 10: [mem 0x40000000-0x400fffff 64bit]

Jul 21 14:31:38 DNS-323 user.debug kernel: pci 0000:00:01.0: reg 18: [io  0xf0000000-0xf00000ff]

Jul 21 14:31:38 DNS-323 user.info kernel: PCI: bus0: Fast back to back transfers disabled

Jul 21 14:31:38 DNS-323 user.debug kernel: pci 0000:01:00.0: reg 10: [mem 0x00000000-0x03ffffff 64bit pref]

Jul 21 14:31:38 DNS-323 user.debug kernel: pci 0000:01:00.0: reg 18: [mem 0x10000000-0x1fffffff 64bit pref]

Jul 21 14:31:38 DNS-323 user.debug kernel: pci 0000:01:00.0: reg 20: [mem 0xf1000000-0xf10fffff 64bit]

Jul 21 14:31:38 DNS-323 user.debug kernel: pci 0000:01:00.0: reg 30: [mem 0xe0000000-0xe7ffffff pref]

Jul 21 14:31:38 DNS-323 user.debug kernel: pci 0000:01:00.0: supports D1 D2

Jul 21 14:31:38 DNS-323 user.debug kernel: pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot

Jul 21 14:31:38 DNS-323 user.debug kernel: pci 0000:01:00.0: PME# disabled

Jul 21 14:31:38 DNS-323 user.info kernel: PCI: bus1: Fast back to back transfers enabled

Jul 21 14:31:38 DNS-323 user.info kernel: pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe00fffff 64bit]

Jul 21 14:31:38 DNS-323 user.info kernel: pci 0000:00:01.0: BAR 0: set to [mem 0xe0000000-0xe00fffff 64bit] (PCI address [0xe0000000-0xe00fffff]

Jul 21 14:31:38 DNS-323 user.info kernel: pci 0000:00:01.0: BAR 2: assigned [io  0x1000-0x10ff]

Jul 21 14:31:38 DNS-323 user.info kernel: pci 0000:00:01.0: BAR 2: set to [io  0x1000-0x10ff] (PCI address [0x1000-0x10ff]

Jul 21 14:31:38 DNS-323 user.warn kernel: bio: create slab <bio-0> at 0

Jul 21 14:31:38 DNS-323 user.notice kernel: SCSI subsystem initialized

Jul 21 14:31:38 DNS-323 user.debug kernel: libata version 3.00 loaded.

Jul 21 14:31:38 DNS-323 user.info kernel: usbcore: registered new interface driver usbfs

Jul 21 14:31:38 DNS-323 user.info kernel: usbcore: registered new interface driver hub

Jul 21 14:31:38 DNS-323 user.info kernel: usbcore: registered new device driver usb

Jul 21 14:31:38 DNS-323 user.info kernel: Switching to clocksource orion_clocksource

Jul 21 14:31:38 DNS-323 user.info kernel: NET: Registered protocol family 2

Jul 21 14:31:38 DNS-323 user.info kernel: IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

Jul 21 14:31:38 DNS-323 user.info kernel: TCP established hash table entries: 2048 (order: 2, 16384 bytes)

Jul 21 14:31:38 DNS-323 user.info kernel: TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

Jul 21 14:31:38 DNS-323 user.info kernel: TCP: Hash tables configured (established 2048 bind 2048)

Jul 21 14:31:38 DNS-323 user.info kernel: TCP reno registered

Jul 21 14:31:38 DNS-323 user.info kernel: NET: Registered protocol family 1

Jul 21 14:31:38 DNS-323 user.info kernel: RPC: Registered udp transport module.

Jul 21 14:31:38 DNS-323 user.info kernel: RPC: Registered tcp transport module.

Jul 21 14:31:38 DNS-323 user.info kernel: RPC: Registered tcp NFSv4.1 backchannel transport module.

Jul 21 14:31:38 DNS-323 user.debug kernel: PCI: CLS 32 bytes, default 32

Jul 21 14:31:38 DNS-323 user.info kernel: Trying to unpack rootfs image as initramfs...

Jul 21 14:31:38 DNS-323 user.info kernel: rootfs image is not initramfs (junk in compressed archive); looks like an initrd

Jul 21 14:31:38 DNS-323 user.info kernel: Freeing initrd memory: 6236K

Jul 21 14:31:38 DNS-323 user.notice kernel: VFS: Disk quotas dquot_6.5.2

Jul 21 14:31:38 DNS-323 user.warn kernel: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

Jul 21 14:31:38 DNS-323 user.info kernel: squashfs: version 4.0 (2009/01/31) Phillip Lougher

Jul 21 14:31:38 DNS-323 user.info kernel: Installing knfsd (copyright (C) 1996 ok...@monad.swb.de).

Jul 21 14:31:38 DNS-323 user.info kernel: aufs 2-standalone.tree-35-20100809

Jul 21 14:31:38 DNS-323 user.info kernel: msgmni has been set to 119

Jul 21 14:31:38 DNS-323 user.info kernel: io scheduler noop registered

Jul 21 14:31:38 DNS-323 user.info kernel: io scheduler deadline registered

Jul 21 14:31:38 DNS-323 user.info kernel: io scheduler cfq registered (default)

Jul 21 14:31:38 DNS-323 user.info kernel: Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled

Jul 21 14:31:38 DNS-323 user.info kernel: serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A

Jul 21 14:31:38 DNS-323 user.info kernel: console [ttyS0] enabled

Jul 21 14:31:38 DNS-323 user.info kernel: brd: module loaded

Jul 21 14:31:38 DNS-323 user.info kernel: loop: module loaded

Jul 21 14:31:38 DNS-323 user.info kernel: sata_mv 0000:00:01.0: version 1.28

Jul 21 14:31:38 DNS-323 user.info kernel: sata_mv 0000:00:01.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx

Jul 21 14:31:38 DNS-323 user.info kernel: scsi0 : sata_mv

Jul 21 14:31:38 DNS-323 user.info kernel: scsi1 : sata_mv

Jul 21 14:31:38 DNS-323 user.info kernel: scsi2 : sata_mv

Jul 21 14:31:38 DNS-323 user.info kernel: scsi3 : sata_mv

Jul 21 14:31:38 DNS-323 user.info kernel: ata1: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0022000 irq 11

Jul 21 14:31:38 DNS-323 user.info kernel: ata2: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0024000 irq 11

Jul 21 14:31:38 DNS-323 user.info kernel: ata3: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0026000 irq 11

Jul 21 14:31:38 DNS-323 user.info kernel: ata4: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0028000 irq 11

Jul 21 14:31:38 DNS-323 user.notice kernel: physmap platform flash device: 00800000 at f4000000

Jul 21 14:31:38 DNS-323 user.info kernel: physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank

Jul 21 14:31:38 DNS-323 user.info kernel: Amd/Fujitsu Extended Query Table at 0x0040

Jul 21 14:31:38 DNS-323 user.notice kernel: number of CFI chips: 1

Jul 21 14:31:38 DNS-323 user.notice kernel: cmdlinepart partition parsing not available

Jul 21 14:31:38 DNS-323 user.notice kernel: RedBoot partition parsing not available

Jul 21 14:31:38 DNS-323 user.notice kernel: Using physmap partition information

Jul 21 14:31:38 DNS-323 user.notice kernel: Creating 5 MTD partitions on "physmap-flash.0":

Jul 21 14:31:38 DNS-323 user.notice kernel: 0x000000000000-0x000000010000 : "MTD1"

Jul 21 14:31:38 DNS-323 user.notice kernel: 0x000000010000-0x000000020000 : "MTD2"

Jul 21 14:31:38 DNS-323 user.notice kernel: 0x000000020000-0x0000001a0000 : "Linux Kernel"

Jul 21 14:31:38 DNS-323 user.notice kernel: 0x0000001a0000-0x0000007d0000 : "File System"

Jul 21 14:31:38 DNS-323 user.notice kernel: 0x0000007d0000-0x000000800000 : "u-boot"

Jul 21 14:31:38 DNS-323 user.notice kernel: MV-643xx 10/100/1000 ethernet driver version 1.4

Jul 21 14:31:38 DNS-323 user.info kernel: mv643xx_eth smi: probed

Jul 21 14:31:38 DNS-323 user.notice kernel: net eth0: port 0 with MAC address XX:XX:XX:XX:XX:XX

Jul 21 14:31:38 DNS-323 user.info kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

Jul 21 14:31:38 DNS-323 user.info kernel: orion-ehci orion-ehci.0: Marvell Orion EHCI

Jul 21 14:31:38 DNS-323 user.info kernel: orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1

Jul 21 14:31:38 DNS-323 user.info kernel: orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000

Jul 21 14:31:38 DNS-323 user.info kernel: orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00

Jul 21 14:31:38 DNS-323 user.info kernel: hub 1-0:1.0: USB hub found

Jul 21 14:31:38 DNS-323 user.info kernel: hub 1-0:1.0: 1 port detected

Jul 21 14:31:38 DNS-323 user.info kernel: Initializing USB Mass Storage driver...

Jul 21 14:31:38 DNS-323 user.info kernel: usbcore: registered new interface driver usb-storage

Jul 21 14:31:38 DNS-323 user.info kernel: USB Mass Storage support registered.

Jul 21 14:31:38 DNS-323 user.info kernel: input: gpio-keys as /class/input/input0

Jul 21 14:31:38 DNS-323 user.info kernel: i2c /dev entries driver

Jul 21 14:31:38 DNS-323 user.info kernel: rtc-m41t80 0-0068: chip found, driver version 0.05

Jul 21 14:31:38 DNS-323 user.info kernel: rtc-m41t80 0-0068: rtc core: registered m41t80 as rtc0

Jul 21 14:31:38 DNS-323 user.info kernel: lm75 0-0048: hwmon1: sensor 'lm75'

Jul 21 14:31:38 DNS-323 user.info kernel: md: linear personality registered for level -1

Jul 21 14:31:38 DNS-323 user.info kernel: md: raid1 personality registered for level 1

Jul 21 14:31:38 DNS-323 user.debug kernel: Registered led device: power:blue

Jul 21 14:31:38 DNS-323 user.debug kernel: Registered led device: right:amber

Jul 21 14:31:38 DNS-323 user.debug kernel: Registered led device: left:amber

Jul 21 14:31:38 DNS-323 user.info kernel: usbcore: registered new interface driver usbhid

Jul 21 14:31:38 DNS-323 user.info kernel: usbhid: USB HID core driver

Jul 21 14:31:38 DNS-323 user.info kernel: TCP cubic registered

Jul 21 14:31:38 DNS-323 user.info kernel: NET: Registered protocol family 17

Jul 21 14:31:38 DNS-323 user.info kernel: rtc-m41t80 0-0068: setting system clock to 2013-07-21 14:31:21 UTC (1374417081)

Jul 21 14:31:38 DNS-323 user.info kernel: ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)

Jul 21 14:31:38 DNS-323 user.info kernel: ata1.00: ATA-7: WDC WD5000YS-01MPB1, 09.02E09, max UDMA/133

Jul 21 14:31:38 DNS-323 user.info kernel: ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)

Jul 21 14:31:38 DNS-323 user.info kernel: ata1.00: configured for UDMA/133

Jul 21 14:31:38 DNS-323 user.notice kernel: scsi 0:0:0:0: Direct-Access     ATA      WDC WD5000YS-01M 09.0 PQ: 0 ANSI: 5

Jul 21 14:31:38 DNS-323 user.notice kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0

Jul 21 14:31:38 DNS-323 user.notice kernel: sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)

Jul 21 14:31:38 DNS-323 user.notice kernel: sd 0:0:0:0: [sda] Write Protect is off

Jul 21 14:31:38 DNS-323 user.debug kernel: sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00

Jul 21 14:31:38 DNS-323 user.notice kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

Jul 21 14:31:38 DNS-323 user.info kernel:  sda: sda1 sda2 sda4

Jul 21 14:31:38 DNS-323 user.notice kernel: sd 0:0:0:0: [sda] Attached SCSI disk

Jul 21 14:31:38 DNS-323 user.info kernel: ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)

Jul 21 14:31:38 DNS-323 user.info kernel: ata2.00: ATA-7: WDC WD5000KS-60MNB0, 08.02E08, max UDMA/100

Jul 21 14:31:38 DNS-323 user.info kernel: ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)

Jul 21 14:31:38 DNS-323 user.info kernel: ata2.00: configured for UDMA/100

Jul 21 14:31:38 DNS-323 user.notice kernel: scsi 1:0:0:0: Direct-Access     ATA      WDC WD5000KS-60M 08.0 PQ: 0 ANSI: 5

Jul 21 14:31:38 DNS-323 user.notice kernel: sd 1:0:0:0: Attached scsi generic sg1 type 0

Jul 21 14:31:38 DNS-323 user.notice kernel: sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB)

Jul 21 14:31:38 DNS-323 user.notice kernel: sd 1:0:0:0: [sdb] Write Protect is off

Jul 21 14:31:38 DNS-323 user.debug kernel: sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00

Jul 21 14:31:38 DNS-323 user.notice kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

Jul 21 14:31:38 DNS-323 user.info kernel:  sdb: sdb1 sdb2 sdb4

Jul 21 14:31:38 DNS-323 user.notice kernel: sd 1:0:0:0: [sdb] Attached SCSI disk

Jul 21 14:31:38 DNS-323 user.info kernel: ata3: SATA link down (SStatus 0 SControl 300)

Jul 21 14:31:38 DNS-323 user.info kernel: ata4: SATA link down (SStatus 0 SControl 300)

Jul 21 14:31:38 DNS-323 user.info kernel: md: Skipping autodetection of RAID arrays. (raid=autodetect will force)

Jul 21 14:31:38 DNS-323 user.notice kernel: RAMDISK: squashfs filesystem found at block 0

Jul 21 14:31:38 DNS-323 user.notice kernel: RAMDISK: Loading 6233KiB [1 disk] into ram disk... |^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H

Jul 21 14:31:38 DNS-323 user.warn kernel: VFS: Mounted root (squashfs filesystem) readonly on device 1:0.

Jul 21 14:31:38 DNS-323 user.info kernel: Freeing init memory: 132K

Jul 21 14:31:38 DNS-323 user.info kernel: Adding 530108k swap on /dev/sda1.  Priority:1 extents:1 across:530108k 

Jul 21 14:31:38 DNS-323 user.info kernel: md: bind<sda2>

Jul 21 14:31:38 DNS-323 user.info kernel: EXT3-fs: barriers not enabled

Jul 21 14:31:38 DNS-323 user.info kernel: kjournald starting.  Commit interval 5 seconds

Jul 21 14:31:38 DNS-323 user.info kernel: Adding 530108k swap on /dev/sdb1.  Priority:1 extents:1 across:530108k 

Jul 21 14:31:38 DNS-323 user.info kernel: EXT3-fs (sda4): using internal journal

Jul 21 14:31:38 DNS-323 user.info kernel: EXT3-fs (sda4): mounted filesystem with ordered data mode

Jul 21 14:31:38 DNS-323 user.info kernel: md: bind<sdb2>

Jul 21 14:31:38 DNS-323 user.info kernel: md/raid1:md0: active with 2 out of 2 mirrors

Jul 21 14:31:38 DNS-323 user.info kernel: md0: detected capacity change from 0 to 498215419904

Jul 21 14:31:38 DNS-323 user.info kernel:  md0: unknown partition table

Jul 21 14:31:39 DNS-323 user.info kernel: EXT3-fs: barriers not enabled

Jul 21 14:31:39 DNS-323 user.info kernel: kjournald starting.  Commit interval 5 seconds

Jul 21 14:31:39 DNS-323 user.info kernel: EXT3-fs (md0): using internal journal

Jul 21 14:31:39 DNS-323 user.info kernel: EXT3-fs (md0): mounted filesystem with ordered data mode

Jul 21 14:31:39 DNS-323 user.notice hot: Users directory found in md0

Jul 21 14:31:40 DNS-323 user.notice hot: Public directory found in md0

Jul 21 14:31:40 DNS-323 user.notice hot: ffp directory found in md0

Jul 21 14:31:41 DNS-323 user.notice hot: Alt-F directory found in md0

Jul 21 14:31:42 DNS-323 cron.info crond[568]: crond: crond (busybox 1.20.2) started, log level 8

Jul 21 14:31:43 DNS-323 daemon.notice sntp[576]: Started sntp

Jul 21 14:31:43 DNS-323 daemon.debug sntp[576]: Error looking up (A) pool.ntp.org: Name or service not known

Jul 21 14:31:43 DNS-323 user.notice root: Starting crond: OK. ntpd: Setting up crontab... OK.

Jul 21 14:31:46 DNS-323 user.notice root: Starting sslcert: Creating SSL self-signed certificate... OK.

Jul 21 14:31:47 DNS-323 daemon.notice rpc.mountd[623]: Version 1.2.7 starting

Jul 21 14:31:47 DNS-323 user.notice root: Starting urandom: OK.

Jul 21 14:31:47 DNS-323 daemon.info sysctrl: Starting

Jul 21 14:31:47 DNS-323 daemon.info sysctrl: reading /etc/sysctrl.conf

Jul 21 14:31:47 DNS-323 daemon.info sysctrl: args.lo_fan=2000

Jul 21 14:31:47 DNS-323 daemon.info sysctrl: args.hi_fan=5000

Jul 21 14:31:47 DNS-323 daemon.info sysctrl: args.lo_temp=40

Jul 21 14:31:47 DNS-323 daemon.info sysctrl: args.hi_temp=50

Jul 21 14:31:47 DNS-323 daemon.info sysctrl: args.mail=1

Jul 21 14:31:47 DNS-323 daemon.info sysctrl: args.recovery=1

Jul 21 14:31:47 DNS-323 user.notice root: Starting sysctrl: OK.

Jul 21 14:31:47 DNS-323 daemon.info sysctrl: args.fan_off_temp=38

Jul 21 14:31:47 DNS-323 daemon.info sysctrl: args.max_fan_speed=6000

Jul 21 14:31:47 DNS-323 daemon.info sysctrl: args.crit_temp=55

Jul 21 14:31:47 DNS-323 daemon.info sysctrl: args.warn_temp=52

Jul 21 14:31:47 DNS-323 daemon.info sysctrl: args.crit_temp_command="/sbin/poweroff"

Jul 21 14:31:47 DNS-323 daemon.info sysctrl: args.warn_temp_command="(null)"

Jul 21 14:31:47 DNS-323 daemon.info sysctrl: args.front_button_command1="(null)"

Jul 21 14:31:47 DNS-323 daemon.info sysctrl: args.front_button_command2="(null)"

Jul 21 14:31:47 DNS-323 daemon.info sysctrl: args.back_button_command="(null)"

Jul 21 14:31:47 DNS-323 daemon.notice rpc.statd[641]: Version 1.2.7 starting

Jul 21 14:31:47 DNS-323 daemon.warn rpc.statd[641]: Flags: 

Jul 21 14:31:48 DNS-323 user.notice hot: Start fscking sdb4

Jul 21 14:31:48 DNS-323 user.info kernel: usbcore: registered new interface driver usblp

Jul 21 14:31:48 DNS-323 daemon.info sysctrl: right_dev disk (sda) wakeup

Jul 21 14:31:48 DNS-323 daemon.info sysctrl: left_dev disk (sdb) wakeup

Jul 21 14:31:48 DNS-323 daemon.notice sm-notify[676]: Version 1.2.7 starting

Jul 21 14:31:48 DNS-323 user.notice root: Starting portmap: .OK. Starting rpc.mountd: OK. Starting rpc.statd: OK. Starting rpc.nfsd: OK. Starting sm-notify: OK.

Jul 21 14:31:49 DNS-323 user.notice hot: Finish fscking sdb4: fsck 1.41.14 (22-Dec-2010) /dev/sdb4: clean, 25/128016 files, 26751/512040 blocks

Jul 21 14:31:49 DNS-323 user.info kernel: EXT3-fs: barriers not enabled

Jul 21 14:31:49 DNS-323 user.info kernel: kjournald starting.  Commit interval 5 seconds

Jul 21 14:31:49 DNS-323 user.info kernel: EXT3-fs (sdb4): using internal journal

Jul 21 14:31:49 DNS-323 user.info kernel: EXT3-fs (sdb4): mounted filesystem with ordered data mode

Jul 21 14:31:50 DNS-323 user.notice root: Starting minidlna: [2013/07/21 14:31:50] minidlna.c:754: fatal: No IP address automatically detected! Fail.

Jul 21 14:31:50 DNS-323 user.notice root: Starting sabnzbd: Fail.

Jul 21 14:31:51 DNS-323 user.notice root: Starting sickbeard: Fail.

Jul 21 14:31:52 DNS-323 user.notice root: dropbear: generating rsa key...  dropbear: generating dsa key...  Starting inetd: OK.

Jul 21 14:31:52 DNS-323 daemon.notice sntp[763]: Started sntp

Jul 21 14:31:52 DNS-323 daemon.debug sntp[763]: Error looking up (A) pool.ntp.org: Name or service not known

Jul 21 14:31:52 DNS-323 user.notice root: ntpd: Setting up crontab... OK.

Jul 21 14:31:53 DNS-323 daemon.notice sm-notify[807]: Version 1.2.7 starting

Jul 21 14:31:53 DNS-323 daemon.notice sm-notify[807]: Already notifying clients; Exiting!

Jul 21 14:31:53 DNS-323 user.notice root: Starting rpc.mountd: OK. Starting rpc.statd: OK. Starting rpc.nfsd: OK. Starting sm-notify: OK.

Jul 21 14:31:54 DNS-323 user.notice root: Starting nmbd: OK. Starting smbd: OK.

Jul 21 14:31:54 DNS-323 user.notice root: Starting ffp: * /ffp/start/syslogd.sh inactive * /ffp/start/SERVERS.sh inactive * /ffp/start/portmap.sh inactive * /ffp/start/unfsd.sh inactive * /ffp/start/nfsd.sh inactive * /ffp/start/ntpd.sh inactive * /ffp/start/LOGIN.sh ina

====================== BOOTLOG ======================

Jul 21 14:31:26 syslogd started: BusyBox v1.20.2

Jul 21 14:31:26 root: Board: A1

Jul 21 14:31:26 root: Firmware: Alt-F-0.1RC3, kernel 2.6.35.14

Jul 21 14:31:29 root: fsck 1.41.14 (22-Dec-2010) fsck.minix: BusyBox v1.20.2 (2013-03-17 19:50:30 WET) /dev/mtdblock0 is clean, check is skipped

Jul 21 14:31:29 root: FIXME: Waiting 3 sec for kernel enumeration to finish...

Jul 21 14:31:32 root: FIXME: stop waiting.

Jul 21 14:31:35 hot: Start fscking sda4

Jul 21 14:31:36 hot: Finish fscking sda4: fsck 1.41.14 (22-Dec-2010) /dev/sda4: clean, 30/128016 files, 27170/512040 blocks

Jul 21 14:31:37 hot: Start fscking md0

Jul 21 14:31:37 hot: sdb4 waiting to be fscked

Jul 21 14:31:38 root: IP from flash-defaults

Jul 21 14:31:38 syslogd exiting

====================== IFCONFIG ======================

lo        Link encap:Local Loopback  

          inet addr:127.0.0.1  Mask:255.0.0.0

          UP LOOPBACK RUNNING  MTU:16436  Metric:1

          RX packets:82 errors:0 dropped:0 overruns:0 frame:0

          TX packets:82 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0 

          RX bytes:6864 (6.7 KiB)  TX bytes:6864 (6.7 KiB)

====================== ROUTE ======================

Kernel IP routing table

Destination     Gateway         Genmask         Flags Metric Ref    Use Iface

127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo

====================== RESOLVER ======================

search workgroup 

====================== HOSTS ======================

127.0.0.1 localhost

====================== DISKS (MBR) ======================

Disk /dev/sda: 60801 cylinders, 255 heads, 63 sectors/track

Units = sectors of 512 bytes, counting from 0

   Device Boot    Start       End   #sectors  Id  System

/dev/sda1            64   1060287    1060224  82  Linux swap

/dev/sda2       2084368 975161559  973077192  83  Linux

/dev/sda3             0         -          0   0  Empty

/dev/sda4       1060288   2084367    1024080  83  Linux

start: (c,h,s) expected (65,254,62) found (68,41,48)

end: (c,h,s) expected (129,190,13) found (133,254,59)

Disk /dev/sdb: 60801 cylinders, 255 heads, 63 sectors/track

Units = sectors of 512 bytes, counting from 0

   Device Boot    Start       End   #sectors  Id  System

/dev/sdb1            64   1060287    1060224  82  Linux swap

/dev/sdb2       2084368 975161559  973077192  83  Linux

/dev/sdb3             0         -          0   0  Empty

/dev/sdb4       1060288   2084367    1024080  83  Linux

start: (c,h,s) expected (65,254,62) found (68,41,48)

end: (c,h,s) expected (129,190,13) found (133,254,59)

====================== DISKS (GPT) ======================

***************************************************************

Found invalid GPT and valid MBR; converting MBR to GPT format.

***************************************************************

Disk /dev/sda: 976773168 sectors, 465.8 GiB

Logical sector size: 512 bytes

Disk identifier (GUID): E2A18759-B023-4194-BDEA-0F33585BDB5B

Partition table holds up to 128 entries

First usable sector is 34, last usable sector is 976773134

Partitions will be aligned on 16-sector boundaries

Total free space is 1611605 sectors (786.9 MiB)

Number  Start (sector)    End (sector)  Size       Code  Name

   1              64         1060287   517.7 MiB   8200  Linux swap

   2         2084368       975161559   464.0 GiB   8300  Linux filesystem

   4         1060288         2084367   500.0 MiB   8300  Linux filesystem

***************************************************************

Found invalid GPT and valid MBR; converting MBR to GPT format.

***************************************************************

Disk /dev/sdb: 976773168 sectors, 465.8 GiB

Logical sector size: 512 bytes

Disk identifier (GUID): AEBBDF5E-7AB7-465E-BFF7-E40788A6FAAC

Partition table holds up to 128 entries

First usable sector is 34, last usable sector is 976773134

Partitions will be aligned on 16-sector boundaries

Total free space is 1611605 sectors (786.9 MiB)

Number  Start (sector)    End (sector)  Size       Code  Name

   1              64         1060287   517.7 MiB   8200  Linux swap

   2         2084368       975161559   464.0 GiB   8300  Linux filesystem

   4         1060288         2084367   500.0 MiB   8300  Linux filesystem

====================== BLOCKID ======================

/dev/mtdblock0: TYPE="minix" 

/dev/sda4: UUID="cb1caccd-5a6f-4f3b-8085-467ae39c6cab" SEC_TYPE="ext2" TYPE="ext3" 

/dev/md0: UUID="e0e57f9e-1c59-46cb-aafa-762d4a7a15f2" SEC_TYPE="ext2" TYPE="ext3" 

/dev/sdb4: UUID="f7ea9db8-f2a9-48cd-884c-c100fc774e3c" TYPE="ext3" SEC_TYPE="ext2" 

/dev/loop0: TYPE="squashfs" 

/dev/mtdblock1: TYPE="minix" 

/dev/sda1: TYPE="swap" 

/dev/sda2: UUID="dd8de673-3c62-5c2f-ebbf-eea2a265fbb8" TYPE="mdraid" 

/dev/sdb1: TYPE="swap" 

/dev/sdb2: UUID="dd8de673-3c62-5c2f-ebbf-eea2a265fbb8" TYPE="mdraid" 

====================== RAID ======================

Personalities : [linear] [raid1] 

md0 : active raid1 sdb2[1] sda2[0]

      486538496 blocks [2/2] [UU]

      

unused devices: <none>

====================== MOUNT ======================

rootfs / rootfs rw 0 0

tmpfs /rootmnt tmpfs rw,relatime 0 0

/rootmnt/dev/loop0 /rootmnt/ro squashfs ro,relatime 0 0

aufs / aufs rw,relatime,si=4073ced1 0 0

proc /proc proc rw,relatime 0 0

usbfs /proc/bus/usb usbfs rw,relatime,devgid=9,devmode=664 0 0

sysfs /sys sysfs rw,relatime 0 0

tmpfs /tmp tmpfs rw,relatime,size=108544k 0 0

devpts /dev/pts devpts rw,relatime,mode=600 0 0

/dev/sda4 /mnt/sda4 ext3 rw,relatime,errors=continue,barrier=0,data=ordered 0 0

/dev/md0 /mnt/md0 ext3 rw,relatime,errors=continue,barrier=0,data=ordered 0 0

nfsd /proc/fs/nfsd nfsd rw,relatime 0 0

/dev/sdb4 /mnt/sdb4 ext3 rw,relatime,errors=continue,barrier=0,data=ordered 0 0

====================== FS ======================

Filesystem                Size      Used Available Use% Mounted on

rootfs                  456.7G      3.3G    453.5G   1% /

tmpfs                    30.0M    132.0K     29.9M   0% /rootmnt

/rootmnt/dev/loop0        6.3M      6.3M         0 100% /rootmnt/ro

aufs                    456.7G      3.3G    453.5G   1% /

tmpfs                   106.0M    552.0K    105.5M   1% /tmp

/dev/sda4               484.3M     10.8M    473.5M   2% /mnt/sda4

/dev/md0                456.7G      3.3G    453.5G   1% /mnt/md0

/dev/sdb4               484.3M     10.3M    473.9M   2% /mnt/sdb4

====================== AUFS ======================

aufs on / type aufs (rw,relatime,si=4073ced1)

/mnt/md0/Alt-F=rw

/rootmnt/rw=rw

/rootmnt/ro=rr

====================== SERVICES ======================

root: user stopped.

root: ffp stopped

root: sickbeard stopped

root: sabnzbd stopped

chown: unknown user/group couchpotato2:TV

root: couchpotato2 stopped

root: minidlna stopped

root: vsftpd stopped

root: dropbear stopped

root: smbd running

root: rpc.statd running

root: nfsd running

root: inadyn stopped

root: ntpd running

root: dnsmasq stopped

root: stunnel stopped

root: inetd running

root: portmap running

root: cleanup stopped

root: backup stopped

root: mdadm stopped

root: smartd stopped

root: atd stopped

root: crond running

root: sysctrl running

root: urandom stopped

root: sslcert stopped.

root: syslogd running

====================== TOP ======================

Mem: 33672K used, 27760K free, 0K shrd, 7980K buff, 16556K cached

CPU:   9% usr   0% sys   0% nic  90% idle   0% io   0% irq   0% sirq

Load average: 0.75 0.19 0.06 1/56 985

  PID  PPID USER     STAT   VSZ %VSZ %CPU COMMAND

  985   825 root     R     1180   2%   9% top -bn1

  817     1 root     S    10416  17%   0% smbd -D

  842   817 root     S    10416  17%   0% smbd -D

  815     1 root     S     7912  13%   0% nmbd -D

  825   493 root     S     1204   2%   0% {S99user} /bin/sh /etc/init.d/S99user start

  497     1 root     S     1204   2%   0% syslogd -C -m 0 -D

  493    63 root     S     1188   2%   0% {rcall} /bin/sh /sbin/rcall start

    1     0 root     S     1184   2%   0% init

   63     1 root     S     1184   2%   0% {rcS} /bin/sh /etc/init.d/rcS

  747     1 root     S     1184   2%   0% inetd

  568     1 root     S     1184   2%   0% crond

  502     1 root     S     1172   2%   0% klogd

  623     1 root     S      908   1%   0% rpc.mountd --no-nfs-version 4

  641     1 daemon   S      628   1%   0% rpc.statd --no-notify

  611     1 daemon   S      592   1%   0% portmap

  637     1 root     S      588   1%   0% sysctrl

   32     2 root     SW       0   0%   0% [mtdblock3]

   51     2 root     SW<      0   0%   0% [loop0]

    9     2 root     SW       0   0%   0% [kblockd/0]

    4     2 root     SW       0   0%   0% [events/0]

   11     2 root     SW       0   0%   0% [ata_sff/0]

    3     2 root     SW       0   0%   0% [ksoftirqd/0]

   37     2 root     SW       0   0%   0% [flush-1:0]

   16     2 root     SW       0   0%   0% [aufsd_pre/0]

  425     2 root     SW       0   0%   0% [md0_raid1]

    7     2 root     SW       0   0%   0% [sync_supers]

   31     2 root     SW       0   0%   0% [mtdblock2]

   29     2 root     SW       0   0%   0% [mtdblock0]

   15     2 root     SW       0   0%   0% [aufsd/0]

   30     2 root     SW       0   0%   0% [mtdblock1]

   17     2 root     SW       0   0%   0% [scsi_eh_0]

   18     2 root     SW       0   0%   0% [scsi_eh_1]

    6     2 root     SW       0   0%   0% [async/mgr]

    8     2 root     SW       0   0%   0% [bdi-default]

  258     2 root     SW       0   0%   0% [flush-31:3]

   19     2 root     SW       0   0%   0% [scsi_eh_2]

   20     2 root     SW       0   0%   0% [scsi_eh_3]

    5     2 root     SW       0   0%   0% [khelper]

  408     2 root     SW       0   0%   0% [kjournald]

  421     2 root     SW       0   0%   0% [flush-8:0]

  519     2 root     SW       0   0%   0% [kjournald]

   33     2 root     SW       0   0%   0% [mtdblock4]

   36     2 root     SW       0   0%   0% [usbhid_resumer]

   10     2 root     SW       0   0%   0% [ata_aux]

  659     2 root     SW       0   0%   0% [nfsd]

  660     2 root     SW       0   0%   0% [nfsd]

  661     2 root     SW       0   0%   0% [nfsd]

  658     2 root     SW       0   0%   0% [lockd]

  699     2 root     SW       0   0%   0% [kjournald]

  726     2 root     SW       0   0%   0% [flush-8:16]

  553     2 root     SW       0   0%   0% [flush-9:0]

  662     2 root     SW       0   0%   0% [nfsd]

   13     2 root     SW       0   0%   0% [rpciod/0]

   14     2 root     SW       0   0%   0% [kswapd0]

    2     0 root     SW       0   0%   0% [kthreadd]

   12     2 root     SW       0   0%   0% [khubd]

====================== FREE ======================

             total         used         free       shared      buffers

Mem:         61432        33684        27748            0         7980

-/+ buffers:              25704        35728

Swap:      1060216            0      1060216

[João Cardoso]

On Sunday, July 21, 2013 4:04:10 PM UTC+1, SCARNG wrote:

I was able to mount the drive using ExT2Fsd and pull the alt-f.log file.

Good

 

 Alt-F is running

You could know that be performing the front-button test, read the About Buttons and Leds wiki

 

- I'm posting the log but have replace the MAX address with XX:XX:XX:XX:XX:XX  ...

 

====================== IFCONFIG ======================

lo        Link encap:Local Loopback  

          inet addr:127.0.0.1  Mask:255.0.0.0

          UP LOOPBACK RUNNING  MTU:16436  Metric:1

          RX packets:82 errors:0 dropped:0 overruns:0 frame:0

          TX packets:82 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0 

          RX bytes:6864 (6.7 KiB)  TX bytes:6864 (6.7 KiB)

Here is the problem, the 'eth0' network interface is not configured.

Somehow the /etc/network/interface file contents seems to be corrupted, or an incorrect copy has been saved into flash memory.

The easiest route will be to apply a  reset.

Now that you have read the About Leds and Buttons wiki you know how to do that -- keep the back button pressed for more than 20 seconds (count the front leds flashing).

Hope that you have saved settings in you computer disk, as the procedure will erase them all and you will have to reconfigure everything :-(

As you have the disk contents available in a PC, what is the contents of 'Alt-F/etc/network/interfaces' 

[SCARNG]

There is no "Alt-F/etc/network/interfaces" directory or files 

G:\Alt-F\etc>dir

 Volume in drive G has no label.

 Volume Serial Number is 8952-B3F0

 Directory of G:\Alt-F\etc

07/21/2013  10:31 AM             1,017 blkid.tab

05/03/2013  07:35 AM               221 exports

04/20/2013  07:18 PM    <DIR>          sickbeard

04/21/2013  06:00 PM             2,777 minidlna.conf

04/20/2013  06:35 PM             5,303 couchpotato2.conf

07/21/2013  10:31 AM             1,017 blkid.tab.old

04/21/2013  05:58 PM               344 group-

04/20/2013  06:08 PM    <DIR>          sabnzbd

07/19/2013  09:27 PM                 0 vsftpd.user_list

04/21/2013  05:58 PM    <DIR>          init.d

04/21/2013  07:26 PM               180 sysctrl.conf

04/20/2013  07:10 PM               969 passwd-

04/30/2013  06:01 AM               380 adjtime.conf

07/21/2013  10:31 AM               174 fstab

04/20/2013  07:10 PM               512 shadow-

04/21/2013  07:43 AM                33 msmtprc.alias

              13 File(s)         12,927 bytes

               3 Dir(s)  486,895,394,816 bytes free

[SCARNG]

There is no back button on my DNS-323 A1 - so I held the front power button for 20 seconds, doesn't appear to reset.  Do I need the drives in the device?  

On Sunday, July 21, 2013 5:13:46 PM UTC-4, João Cardoso wrote:

[Joao Cardoso]

On Jul 22, 2013 12:56 AM, "SCARNG" <sca...@gmail.com> wrote:
>
> There is no back button on my DNS-323 A1

in the b1 it is a recessed button, accessible only with a sharp pencil or paper clip

> --
> You received this message because you are subscribed to the Google Groups "Alt-F" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to alt-f+un...@googlegroups.com.
> To post to this group, send email to al...@googlegroups.com.
> Visit this group at http://groups.google.com/group/alt-f.
> To view this discussion on the web visit https://groups.google.com/d/msgid/alt-f/c3a55696-215b-4dd5-b021-ca27cdf2768b%40googlegroups.com.
>
> For more options, visit https://groups.google.com/groups/opt_out.
>  
>  

[SCARNG]

That did the trick, I now see the DNS-323 on the network.  Time to start over - good time anyway as I have two new drives.   

[Chris Burnett]

I'm having a similar issue, although for me the issue was caused by myself (I think) I've always run ALT-F on 2 DNS-323s with static I.P. s and last night  we got a new internet provider and had to switch from 192.168.0.x to 192.168.1.x(No option to stay as the 192.168.0.1 goes to the satellite equipment.) It was a bit of a pain because I had to set the I.P. of my computer in order to connect etc, so after getting it switched to 192.168.1.201, I logged into the box just fine. Then came the moment where I should have left well enough alone and decided to change it so the DHCP server in the router assigned a reserved I.P. to the DNS-323, and switch the DNS-323 to resolve IP by DHCP. After switching the DNS-323 to DHCP I rebooted it and..... gone, doesn't show up in network, doesn't show in the connected DHCP clients list on the router, and doesn't respond at the old address (or the 192.168.1.240-254 IP range either). I was going to do a reset via the back button, but I wanted to check that I can get the data back after the reset. I had the drives set in RAID 0.

[João Cardoso]

On Saturday, September 28, 2013 2:34:39 AM UTC+1, Chris Burnett wrote:

I'm having a similar issue, although for me the issue was caused by myself (I think) I've always run ALT-F on 2 DNS-323s with static I.P. s and last night  we got a new internet provider and had to switch from 192.168.0.x to 192.168.1.x(No option to stay as the 192.168.0.1 goes to the satellite equipment.) It was a bit of a pain because I had to set the I.P. of my computer in order to connect etc, so after getting it switched to 192.168.1.201, I logged into the box just fine. Then came the moment where I should have left well enough alone and decided to change it so the DHCP server in the router assigned a reserved I.P. to the DNS-323, and switch the DNS-323 to resolve IP by DHCP. After switching the DNS-323 to DHCP

The box changes to DHCP as soon as you hit the Submit button in the Setup->Host page. You don't need to reboot the box; if you do it, you have to save settings before you do it.

The most reliable way of doing the change to DHCP is to do it in the old network, verify that it works, then change the network. Some DHCP servers have a very long lease time, 24 hours, and that might cause issues.

I rebooted it and..... gone, doesn't show up in network, doesn't show in the connected DHCP clients list on the router, and doesn't respond at the old address (or the 192.168.1.240-254 IP range either).

There has been similar reports, and I suspect that to be a corrupted network configuration file.

You can try to boot the box with the network cable disconnected; in this case it will not receive an IP from the DHCP server and it will assign itself the 192.168.1.254 IP; you can then make a direct-cable connection to a computer with a static IP in the same network.

I was going to do a reset via the back button, but I wanted to check that I can get the data back after the reset. I had the drives set in RAID 0.

Clearing settings, either through the back reset button or the webUI means just that: delete the saved settings in flash memory -- that has no effect on the disks. Of course you will loose all your definitions: your users, shares, network settings, hostname, services configuration, etc.

Alt-F uses whatever disks it finds, with whatever disk partition scheme and filesystems, and don't change anything on them!

 

[Chris Burnett]

Thank you very much for your help Joao. I'll give the unplugged from network a try, and failing that I'm not as fearful about hitting the reset.

[João Cardoso]

On Saturday, September 28, 2013 6:14:05 PM UTC+1, Chris Burnett wrote:

Thank you very much for your help Joao. I'll give the unplugged from network a try,

I'm sorry, I have been examining the code and that will not work, you really have to perform the back-button "reset" (read the about buttons and leds wiki) :-(