--- dm2613 2005-09-26 01:55:34.000000000 -0400 +++ dm2614 2005-09-26 01:16:52.000000000 -0400 @@ -1,4 +1,4 @@ -Linux version 2.6.13.1 (root@blaze) (gcc version 3.3.6) #2 SMP Mon Sep 12 13:29:14 EDT 2005 +Linux version 2.6.14-rc2-mm1 (root@blaze) (gcc version 3.3.6) #1 SMP Sun Sep 25 17:03:22 EDT 2005 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f400 (usable) BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved) @@ -12,9 +12,10 @@ 511MB LOWMEM available. found SMP MP-table at 000f5a30 On node 0 totalpages: 131056 - DMA zone: 4096 pages, LIFO batch:1 - Normal zone: 126960 pages, LIFO batch:31 - HighMem zone: 0 pages, LIFO batch:1 + DMA zone: 4096 pages, LIFO batch:2 + DMA32 zone: 0 pages, LIFO batch:2 + Normal zone: 126960 pages, LIFO batch:64 + HighMem zone: 0 pages, LIFO batch:2 DMI 2.3 present. ACPI: RSDP (v000 Nvidia ) @ 0x000f7dc0 ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040 @@ -42,22 +43,22 @@ ACPI: IRQ15 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information -Allocating PCI resources starting at 20000000 (gap: 20000000:c0000000) +Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000) Built 1 zonelists -Kernel command line: root=/dev/sda1 ro vmalloc=256M console=ttyS0,57600n8 console=tty0 rootflags=quota elevator=cfq vga=795 mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Initializing CPU#0 -CPU 0 irqstacks, hard=c0469000 soft=c0467000 +Kernel command line: root=/dev/sda1 ro vmalloc=256M console=ttyS0,57600n8 console=tty0 rootflags=quota elevator=cfq vga=795 +CPU 0 irqstacks, hard=c043e000 soft=c043c000 PID hash table entries: 2048 (order: 11, 32768 bytes) -Detected 2352.785 MHz processor. +Detected 2352.758 MHz processor. Using tsc for high-res timesource Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) -Memory: 514984k/524224k available (2353k kernel code, 8756k reserved, 877k data, 228k init, 0k highmem) +Memory: 515152k/524224k available (2390k kernel code, 8560k reserved, 662k data, 232k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. -Calibrating delay using timer specific routine.. 4708.36 BogoMIPS (lpj=2354181) +Calibrating delay using timer specific routine.. 4708.36 BogoMIPS (lpj=2354180) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: After vendor identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 @@ -68,14 +69,15 @@ Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. mtrr: v2.0 (20020519) -Enabling fast FPU save and restore... done. +Enabling fast FPU save and restore... <7>spurious 8259A interrupt: IRQ7. +done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02 Booting processor 1/1 eip 2000 -CPU 1 irqstacks, hard=c046a000 soft=c0468000 +CPU 1 irqstacks, hard=c043f000 soft=c043d000 Initializing CPU#1 -Calibrating delay using timer specific routine.. 4704.68 BogoMIPS (lpj=2352342) +Calibrating delay using timer specific routine.. 4704.69 BogoMIPS (lpj=2352349) CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: After vendor identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) @@ -85,7 +87,7 @@ Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02 -Total of 2 processors activated (9413.04 BogoMIPS). +Total of 2 processors activated (9413.05 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 pin1=0 pin2=-1 checking TSC synchronization across 2 CPUs: @@ -95,13 +97,12 @@ NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 3.00 entry at 0xf2740, last bus=5 -PCI: Using configuration type 1 -ACPI: Subsystem revision 20050408 +PCI: Using MMCONFIG +ACPI: Subsystem revision 20050902 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) -ACPI: Assume root bridge [\_SB_.PCI0] segment is 0 PCI: Transparent bridge - 0000:00:09.0 Boot video device is 0000:01:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] @@ -144,16 +145,16 @@ SCSI subsystem initialized PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report -pnp: 00:00: ioport range 0x4000-0x407f could not be reserved -pnp: 00:00: ioport range 0x4080-0x40ff has been reserved -pnp: 00:00: ioport range 0x4400-0x447f has been reserved -pnp: 00:00: ioport range 0x4480-0x44ff could not be reserved -pnp: 00:00: ioport range 0x4800-0x487f has been reserved -pnp: 00:00: ioport range 0x4880-0x48ff has been reserved +pnp: 00:01: ioport range 0x4000-0x407f could not be reserved +pnp: 00:01: ioport range 0x4080-0x40ff has been reserved +pnp: 00:01: ioport range 0x4400-0x447f has been reserved +pnp: 00:01: ioport range 0x4480-0x44ff could not be reserved +pnp: 00:01: ioport range 0x4800-0x487f has been reserved +pnp: 00:01: ioport range 0x4880-0x48ff has been reserved PCI: Bridge: 0000:00:09.0 IO window: 8000-afff MEM window: d0000000-d1ffffff - PREFETCH window: 20000000-200fffff + PREFETCH window: 30000000-300fffff PCI: Bridge: 0000:00:0b.0 IO window: disabled. MEM window: disabled. @@ -175,7 +176,6 @@ PCI: Setting latency timer of device 0000:00:0c.0 to 64 PCI: Setting latency timer of device 0000:00:0d.0 to 64 PCI: Setting latency timer of device 0000:00:0e.0 to 64 -Machine check exception polling timer started. Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) @@ -187,6 +187,7 @@ vesafb: protected mode interface info at c000:d620 vesafb: scrolling: redraw vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0 +vesafb: Mode is VGA compatible Console: switching to colour frame buffer device 160x64 fb0: VESA VGA frame buffer device ACPI: Power Button (FF) [PWRF] @@ -201,7 +202,10 @@ Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A +mice: PS/2 mouse device common for all mice io scheduler noop registered +io scheduler anticipatory registered +io scheduler deadline registered io scheduler cfq registered (default) RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 @@ -219,20 +223,18 @@ Probing IDE interface ide1... ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18 ACPI: PCI Interrupt 0000:05:08.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 16 -scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36 +scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0 aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs Vendor: PLEXTOR Model: CD-R PX-W1210S Rev: 1.06 Type: CD-ROM ANSI SCSI revision: 02 - target0:0:4: asynchronous. target0:0:4: Beginning Domain Validation target0:0:4: Domain Validation skipping write tests target0:0:4: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 16) target0:0:4: Ending Domain Validation Vendor: IBM Model: IC35L036UWD210-0 Rev: S5CQ Type: Direct-Access ANSI SCSI revision: 03 - target0:0:6: asynchronous. scsi0:A:6:0: Tagged Queuing enabled. Depth 32 target0:0:6: Beginning Domain Validation target0:0:6: wide asynchronous. @@ -244,12 +246,11 @@ SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 > Attached scsi disk sda at scsi0, channel 0, id 6, lun 0 -mice: PS/2 mouse device common for all mice device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com NET: Registered protocol family 2 IP route cache hash table entries: 8192 (order: 3, 32768 bytes) -TCP established hash table entries: 32768 (order: 7, 524288 bytes) -TCP bind hash table entries: 32768 (order: 6, 393216 bytes) +TCP established hash table entries: 32768 (order: 6, 262144 bytes) +TCP bind hash table entries: 32768 (order: 6, 262144 bytes) TCP: Hash tables configured (established 32768 bind 32768) TCP reno registered TCP bic registered @@ -257,13 +258,12 @@ NET: Registered protocol family 17 Starting balanced_irq Using IPI Shortcut mode -swsusp: Suspend partition has wrong signature? BIOS EDD facility v0.16 2004-Jun-25, 2 devices found XFS mounting filesystem sda1 Ending clean XFS mount for filesystem: sda1 VFS: Mounted root (xfs filesystem) readonly. -Freeing unused kernel memory: 228k freed -Adding 506008k swap on /dev/sda7. Priority:-1 extents:1 +Freeing unused kernel memory: 232k freed +Adding 506008k swap on /dev/sda7. Priority:-1 extents:1 across:506008k Linux agpgart interface v0.101 (c) Dave Jones XFS mounting filesystem sda2 Ending clean XFS mount for filesystem: sda2 @@ -273,7 +273,7 @@ Ending clean XFS mount for filesystem: sda5 XFS mounting filesystem sda6 Ending clean XFS mount for filesystem: sda6 -forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.35. +forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.41. ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:0a.0 to 64 @@ -285,10 +285,6 @@ ACPI: PCI Interrupt 0000:05:0c.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 18 eth1: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter PrefPort:A RlmtMode:Check Link State -nvidia: module license 'NVIDIA' taints kernel. -ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 16 -PCI: Setting latency timer of device 0000:01:00.0 to 64 -NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7676 Fri Jul 29 12:58:54 PDT 2005 ieee1394: Initialized config rom entry `ip1394' ohci1394: $Rev: 1299 $ Ben Collins ACPI: PCI Interrupt 0000:05:07.2[B] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 16 @@ -300,7 +296,7 @@ ACPI: PCI Interrupt 0000:05:07.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 18 Installing spdif_bug patch: Audigy 2 Platinum [SB0240P] libata version 1.12 loaded. -sata_nv version 0.6 +sata_nv version 0.8 ACPI: PCI Interrupt Link [APSI] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 22 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:07.0 to 64 @@ -317,18 +313,18 @@ ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xC408 irq 21 ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023c0091065c55] ata3: dev 0 cfg 49:2f00 82:346b 83:7f61 84:4003 85:3469 86:3c41 87:4003 88:407f -ata3: dev 0 ATA, max UDMA/133, 390721968 sectors: lba48 +ata3: dev 0 ATA-6, max UDMA/133, 390721968 sectors: LBA48 nv_sata: Primary device added nv_sata: Primary device removed nv_sata: Secondary device added nv_sata: Secondary device removed ata3: dev 0 configured for UDMA/133 scsi3 : sata_nv +ieee1394: Host added: ID:BUS[1-00:1023] GUID[0011d800004f6359] ata4: no device found (phy stat 00000000) scsi4 : sata_nv Vendor: ATA Model: WDC WD2000JD-00H Rev: 08.0 Type: Direct-Access ANSI SCSI revision: 05 -ieee1394: Host added: ID:BUS[1-00:1023] GUID[0011d800004f6359] SCSI device sdb: 390721968 512-byte hdwr sectors (200050 MB) SCSI device sdb: drive cache: write back SCSI device sdb: 390721968 512-byte hdwr sectors (200050 MB) @@ -343,14 +339,14 @@ ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 20 ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCJ] -> GSI 20 (level, low) -> IRQ 22 PCI: Setting latency timer of device 0000:00:04.0 to 64 -intel8x0_measure_ac97_clock: measured 50740 usecs -intel8x0: clocking to 46837 +intel8x0_measure_ac97_clock: measured 51749 usecs +intel8x0: clocking to 46867 usbcore: registered new driver usbfs usbcore: registered new driver hub ACPI: PCI Interrupt Link [APCL] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 23 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:02.1 to 64 -ehci_hcd 0000:00:02.1: nVidia Corporation CK804 USB Controller +ehci_hcd 0000:00:02.1: EHCI Host Controller ehci_hcd 0000:00:02.1: debug port 1 ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:02.1: irq 17, io mem 0xfeb00000 @@ -363,12 +359,12 @@ ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 22 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:02.0 to 64 -ohci_hcd 0000:00:02.0: nVidia Corporation CK804 USB Controller +ohci_hcd 0000:00:02.0: OHCI Host Controller ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:02.0: irq 20, io mem 0xd2004000 -usb 1-2: new high speed USB device using ehci_hcd and address 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 10 ports detected +usb 1-2: new high speed USB device using ehci_hcd and address 2 hub 1-2:1.0: USB hub found hub 1-2:1.0: 4 ports detected i2c_adapter i2c-0: nForce2 SMBus adapter at 0x4c00 @@ -384,11 +380,13 @@ input: USB HID v1.10 Keyboard [Microsoft Natural Keyboard Pro] on usb-0000:00:02.0-3.1 input: USB HID v1.10 Device [Microsoft Natural Keyboard Pro] on usb-0000:00:02.0-3.1 usbcore: registered new driver usbhid -drivers/usb/input/hid-core.c: v2.01:USB HID core driver +drivers/usb/input/hid-core.c: v2.6:USB HID core driver Real Time Clock Driver v1.12 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 parport: PnPBIOS parport detected. parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA] -gameport: NS558 PnP Gameport is pnp00:0b/gameport0, io 0x201, speed 917kHz +gameport: NS558 PnP Gameport is pnp00:0b/gameport0, io 0x201, speed 903kHz USB Universal Host Controller Interface driver v2.3 +NET: Registered protocol family 10 +IPv6 over IPv4 tunneling driver