Bootdata ok (command line is root=/dev/hdc6 vga=792 selinux=0 noapic nmi_watchdog=0 resume=/dev/hdc3 console=ttyS0,57600 console=tty0 debug) Linux version 2.6.13-rc2 (rafael@albercik) (gcc version 3.3.5 20050117 (prerelease) (SUSE Linux)) #1 Wed Jul 6 10:59:14 CEST 2005 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000002ff40000 (usable) BIOS-e820: 000000002ff40000 - 000000002ff50000 (ACPI data) BIOS-e820: 000000002ff50000 - 0000000030000000 (ACPI NVS) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000f76e0 ACPI: RSDT (v001 A M I OEMRSDT 0x05000425 MSFT 0x00000097) @ 0x000000002ff40000 ACPI: FADT (v001 A M I OEMFACP 0x05000425 MSFT 0x00000097) @ 0x000000002ff40200 ACPI: OEMB (v001 A M I OEMBIOS 0x05000425 MSFT 0x00000097) @ 0x000000002ff50040 >>> ERROR: Invalid checksum ACPI: DSDT (v001 L5DK8 L5DK8014 0x00000014 INTL 0x02002026) @ 0x0000000000000000 On node 0 totalpages: 196416 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 192320 pages, LIFO batch:31 HighMem zone: 0 pages, LIFO batch:1 Nvidia board detected. Ignoring ACPI timer override. ACPI: PM-Timer IO Port: 0x4008 Intel MultiProcessor Specification v1.1 Virtual Wire compatibility mode. OEM ID: ASUSTeK <6>Product ID: L5D <6>APIC at: 0xFEE00000 Processor #0 15:4 APIC version 16 I/O APIC #1 Version 17 at 0xFEC00000. Setting APIC routing to flat Processors: 1 Allocating PCI resources starting at 30000000 (gap: 30000000:cec00000) Checking aperture... CPU 0: aperture @ e8000000 size 128 MB Built 1 zonelists Kernel command line: root=/dev/hdc6 vga=792 selinux=0 noapic nmi_watchdog=0 resume=/dev/hdc3 console=ttyS0,57600 console=tty0 debug Initializing CPU#0 PID hash table entries: 4096 (order: 12, 131072 bytes) time.c: Using 3.579545 MHz PM timer. time.c: Detected 1795.408 MHz processor. time.c: Using PIT/TSC based timekeeping. Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) Memory: 767860k/785664k available (2847k kernel code, 17340k reserved, 1145k data, 176k init) Calibrating delay using timer specific routine.. 3594.88 BogoMIPS (lpj=7189769) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU: AMD Athlon(tm) 64 Processor 3000+ stepping 0a ACPI: setting ELCR to 0200 (from 0c20) Using local APIC timer interrupts. Detected 12.468 MHz APIC timer. testing NMI watchdog ... CPU#0: NMI appears to be stuck (0->0)! NET: Registered protocol family 16 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20050309 ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) Boot video device is 0000:01:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: Embedded Controller [EC0] (gpe 37) Losing some ticks... checking if CPU frequency changed. ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LUS0] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LUS1] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LUS2] (IRQs 3 4 *5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LKLN] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LAUI] (IRQs 3 4 5 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LKMO] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LKSM] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LTID] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LATA] (IRQs 3 4 6 7 10 11 12 *14 15) ACPI: Power Resource [GFAN] (off) usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Failed to allocate mem resource #10:2000000@100000000 for 0000:02:01.0 PCI: Failed to allocate mem resource #10:2000000@100000000 for 0000:02:01.1 PCI: Failed to allocate I/O resource #7:1000@e000 for 0000:02:01.1 PCI: Failed to allocate I/O resource #8:1000@e000 for 0000:02:01.1 PCI: Bus 3, cardbus bridge: 0000:02:01.0 IO window: 0000b000-0000bfff IO window: 0000c000-0000cfff PREFETCH window: 30000000-31ffffff PCI: Bus 7, cardbus bridge: 0000:02:01.1 PREFETCH window: 32000000-33ffffff PCI: Bridge: 0000:00:0a.0 IO window: b000-dfff MEM window: f8a00000-feafffff PREFETCH window: 30000000-34ffffff PCI: Bridge: 0000:00:0b.0 IO window: disabled. MEM window: f6900000-f89fffff PREFETCH window: c6800000-e67fffff PCI: Setting latency timer of device 0000:00:0a.0 to 64 PCI: Device 0000:02:01.0 not available because of resource collisions PCI: Device 0000:02:01.1 not available because of resource collisions agpgart: Detected AGP bridge 0 agpgart: Setting up Nforce3 AGP. agpgart: AGP aperture is 128M @ 0xe8000000 PCI-DMA: Disabling IOMMU. IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ audit: initializing netlink socket (disabled) audit(1120648306.516:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) Initializing Cryptographic API vesafb: framebuffer at 0xd0000000, mapped to 0xffffc20000100000, using 6144k, total 65536k vesafb: mode is 1024x768x32, linelength=4096, pages=1 vesafb: scrolling: redraw vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device Real Time Clock Driver v1.12 Linux agpgart interface v0.101 (c) Dave Jones i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered RAMDISK driver initialized: 16 RAM disks of 128000K size 1024 blocksize loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx NFORCE3-150: IDE controller at PCI slot 0000:00:08.0 NFORCE3-150: chipset revision 165 NFORCE3-150: not 100% native mode: will probe irqs later NFORCE3-150: BIOS didn't set cable bits correctly. Enabling workaround. NFORCE3-150: 0000:00:08.0 (rev a5) UDMA133 controller ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:DMA ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hdb: TOSHIBA DVD-ROM SD-R2512, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: IC25N060ATMR04-0, ATA DISK drive ide1 at 0x170-0x177,0x376 on irq 15 hdc: max request size: 1024KiB hdc: 117210240 sectors (60011 MB) w/7884KiB Cache, CHS=16383/255/63, UDMA(100) hdc: cache flushes supported hdc: hdc1 hdc2 hdc3 hdc4 < hdc5 hdc6 hdc7 hdc8 hdc9 hdc10 > usbmon: debugs is not available mice: PS/2 mouse device common for all mice input: PC Speaker NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 6, 262144 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 9, 3670016 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered TCP bic registered NET: Registered protocol family 1 Using IPI Shortcut mode powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.40.2) powernow-k8: 0 : fid 0x0 (800 MHz), vid 0x12 (1100 mV) powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0x6 (1400 mV) powernow-k8: 2 : fid 0xa (1800 MHz), vid 0x2 (1500 mV) cpu_init done, current fid 0xa, vid 0x2 PM: Checking swsusp image. swsusp: Resume From Partition /dev/hdc3 input: AT Translated Set 2 keyboard on isa0060/serio0 swsusp: Suspend partition has wrong signature? swsusp: Error -22 check for resume file PM: Resume from disk failed. ACPI wakeup devices: MDM P0P1 LAN0 LAN1 USB0 USB1 USB2 SLPB ACPI: (supports S0 S1 S3 S4 S5) EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 176k freed kjournald starting. Commit interval 5 seconds Synaptics Touchpad, model: 1, fw: 5.9, id: 0x926eb1, caps: 0x804719/0x0 input: SynPS/2 Synaptics TouchPad on isa0060/serio4 spurious 8259A interrupt: IRQ7. EXT3 FS on hdc6, internal journal parport0: PC-style at 0x378 [PCSPP,TRISTATE] lp0: using parport0 (polling). device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 cdrom: open failed. SCSI subsystem initialized cdrom: open failed. kjournald starting. Commit interval 5 seconds EXT3 FS on hdc5, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on hdc7, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on hdc8, internal journal EXT3-fs: mounted filesystem with ordered data mode. ReiserFS: hdc9: found reiserfs format "3.6" with standard journal ReiserFS: hdc9: using ordered data mode ReiserFS: hdc9: journal params: device hdc9, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hdc9: checking transaction log (hdc9) ReiserFS: hdc9: Using r5 hash to sort names st: Version 20050501, fixed bufsize 32768, s/g segs 256 ReiserFS: hdc10: found reiserfs format "3.6" with standard journal ReiserFS: hdc10: using ordered data mode ReiserFS: hdc10: journal params: device hdc10, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hdc10: checking transaction log (hdc10) ReiserFS: hdc10: Using r5 hash to sort names ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10 eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter PrefPort:A RlmtMode:Check Link State ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:02.0 to 64 ohci_hcd 0000:00:02.0: nVidia Corporation nForce3 USB 1.1 ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:02.0: irq 11, io mem 0xfebfb000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS1] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:02.1 to 64 ohci_hcd 0000:00:02.1: nVidia Corporation nForce3 USB 1.1 (#2) ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:02.1: irq 11, io mem 0xfebfc000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected usb 2-2: new low speed USB device using ohci_hcd and address 2 ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [LUS2] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:02.2 to 64 ehci_hcd 0000:00:02.2: nVidia Corporation nForce3 USB 2.0 ehci_hcd 0000:00:02.2: debug port 1 ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3 ehci_hcd 0000:00:02.2: irq 5, io mem 0xfebfdc00 PCI: cache line size of 64 is not supported by device 0000:00:02.2 ehci_hcd 0000:00:02.2: park 0 ehci_hcd 0000:00:02.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004 hub 3-0:1.0: USB hub found hub 3-0:1.0: 6 ports detected usb 2-2: USB disconnect, address 2 ohci_hcd 0000:00:02.1: wakeup usb 2-2: new low speed USB device using ohci_hcd and address 3 usbcore: registered new driver hiddev input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:02.1-2 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.01:USB HID core driver Adding 1534196k swap on /dev/hdc3. Priority:42 extents:1 PCI: Device 0000:02:01.0 not available because of resource collisions yenta_cardbus: probe of 0000:02:01.0 failed with error -16 PCI: Device 0000:02:01.1 not available because of resource collisions yenta_cardbus: probe of 0000:02:01.1 failed with error -16 ds: ds_open(socket 0) ds: ds_open(socket 0) NET: Registered protocol family 17 eth0: network connection up using port A speed: 100 autonegotiation: yes duplex mode: full flowctrl: symmetric irq moderation: disabled scatter-gather: enabled NET: Registered protocol family 10 Disabled Privacy Extensions on device ffffffff804a88c0(lo) IPv6 over IPv4 tunneling driver ip6_tables: (C) 2000-2002 Netfilter core team ip_tables: (C) 2000-2002 Netfilter core team ip_conntrack version 2.1 (3069 buckets, 24552 max) - 336 bytes per conntrack Disabled Privacy Extensions on device ffff81002cfc2200(sit0) eth0: no IPv6 routers present ACPI: PCI Interrupt Link [LAUI] enabled at IRQ 10 ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LAUI] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:06.0 to 64 intel8x0_measure_ac97_clock: measured 67166 usecs intel8x0: clocking to 48000 ACPI: AC Adapter [AC0] (on-line) ACPI: Battery Slot [BAT0] (battery present) ACPI: Power Button (FF) [PWRF] ACPI: Sleep Button (CM) [SLPB] ACPI: Lid Switch [LID] ACPI: Fan [FN00] (off) ACPI: Thermal Zone [THRM] (54 C) usbcore: registered new driver usbserial drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic usbcore: registered new driver usbserial_generic drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0 ds: ds_open(socket 0) ds: ds_open(socket 0) ds: ds_open(socket 0) ds: ds_open(socket 0) ds: ds_open(socket 0) ds: ds_open(socket 0) ds: ds_open(socket 0) ds: ds_open(socket 0) ds: ds_open(socket 0)