[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.4.21 (nilesh@i5) (gcc version 6.1.0 (Buildroot 2016.08-g2a18369-dirty) ) #3 Sun Sep 18 21:12:21 IST 2016 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI AM335x BeagleBone Black [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 131072 [ 0.000000] free_area_init_node: node 0, pgdat c04e8800, node_mem_map dfbfa000 [ 0.000000] Normal zone: 1024 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 131072 pages, LIFO batch:31 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon ) [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: root=/dev/mmcblk0p2 rootdelay=5 console=ttyS0,115200n8 console=tty0 ip=dhcp [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 514320K/524288K available (3779K kernel code, 132K rwdata, 852K rodata, 232K init, 141K bss, 9968K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] .text : 0xc0008000 - 0xc048dfa4 (4632 kB) [ 0.000000] .init : 0xc048e000 - 0xc04c8000 ( 232 kB) [ 0.000000] .data : 0xc04c8000 - 0xc04e91d0 ( 133 kB) [ 0.000000] .bss : 0xc04ec000 - 0xc050f71c ( 142 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000014] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000032] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000041] OMAP clocksource: timer1 at 24000000 Hz [ 0.000566] clocksource_probe: no matching clocksources found [ 0.000690] Console: colour dummy device 80x30 [ 0.001073] console [tty0] enabled [ 0.001118] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) [ 0.089255] pid_max: default: 32768 minimum: 301 [ 0.089374] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.089401] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.089862] CPU: Testing write buffer coherency: ok [ 0.090191] Setting up static identity map for 0x80008200 - 0x80008258 [ 0.091672] devtmpfs: initialized [ 0.105628] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.118242] omap_hwmod: debugss: _wait_target_disable failed [ 0.172770] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.172959] pinctrl core: initialized pinctrl subsystem [ 0.174200] NET: Registered protocol family 16 [ 0.174691] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.178552] OMAP GPIO hardware version 0.1 [ 0.195399] edma 49000000.edma: TI EDMA DMA engine driver [ 0.197550] usbcore: registered new interface driver usbfs [ 0.197650] usbcore: registered new interface driver hub [ 0.197735] usbcore: registered new device driver usb [ 0.198085] omap_i2c 44e0b000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c0_pins, deferring probe [ 0.198161] omap_i2c 4819c000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c2_pins, deferring probe [ 0.198313] pps_core: LinuxPPS API ver. 1 registered [ 0.198336] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.198387] PTP clock support registered [ 0.199180] clocksource: Switched to clocksource timer1 [ 0.207065] NET: Registered protocol family 2 [ 0.207627] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.207697] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.207750] TCP: Hash tables configured (established 4096 bind 4096) [ 0.207837] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.207868] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.208006] NET: Registered protocol family 1 [ 0.210318] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.221421] io scheduler noop registered [ 0.221478] io scheduler deadline registered (default) [ 0.221925] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 0.222769] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.224094] console [ttyS0] disabled [ 0.224167] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 158, base_baud = 3000000) is a 8250 [ 0.668625] console [ttyS0] enabled [ 0.673302] omap_rng 48310000.rng: OMAP Random Number Generator ver. 20 [ 0.680122] [drm] Initialized drm 1.1.0 20060810 [ 0.749231] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 0.755404] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 0.761990] davinci_mdio: dt: updated phy_id[0] from phy_mask[fffffffe] [ 0.769296] libphy: 4a101000.mdio: probed [ 0.773356] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver unknown [ 0.781834] cpsw 4a100000.ethernet: Detected MACID = ec:24:b8:9e:15:cc [ 0.789504] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.796100] ehci-omap: OMAP-EHCI Host Controller driver [ 0.801781] mousedev: PS/2 mouse device common for all mice [ 0.808400] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0 [ 0.815676] i2c /dev entries driver [ 0.820093] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 0.827518] omap_hsmmc 48060000.mmc: Got CD GPIO [ 0.910117] ledtrig-cpu: registered to indicate activity on CPUs [ 0.916472] NET: Registered protocol family 17 [ 0.921119] omap_voltage_late_init: Voltage driver support not added [ 0.927879] ThumbEE CPU extension supported. [ 0.934177] input: tps65217_pwr_but as /devices/platform/ocp/44e0b000.i2c/i2c-0/0-0024/input/input0 [ 0.957848] mmc0: host does not support reading read-only switch, assuming write-enable [ 0.970409] mmc0: new high speed SD card at address e624 [ 0.976315] mmcblk0: mmc0:e624 SU02G 1.84 GiB [ 0.984177] tps65217 0-0024: TPS65217 ID 0xe version 1.2 [ 0.989958] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 0.997351] mmcblk0: p1 p2 [ 1.043311] mmc1: MAN_BKOPS_EN bit is not set [ 1.051557] mmc1: new high speed MMC card at address 0001 [ 1.057475] mmcblk1: mmc1:0001 MMC04G 3.66 GiB [ 1.062318] mmcblk1boot0: mmc1:0001 MMC04G partition 1 1.00 MiB [ 1.068439] mmcblk1boot1: mmc1:0001 MMC04G partition 2 1.00 MiB [ 1.121406] tda998x 0-0070: found TDA19988 [ 1.126649] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_ops) [ 1.132748] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 1.139415] [drm] No driver support for vblank timestamp query. [ 1.145613] tilcdc 4830e000.lcdc: No connectors reported connected with modes [ 1.152829] [drm] Cannot find any crtc or sizes - going 1024x768 [ 1.166908] Console: switching to colour frame buffer device 128x48 [ 1.178559] tilcdc 4830e000.lcdc: fb0: frame buffer device [ 1.184247] [drm] Initialized tilcdc 1.0.0 20121205 on minor 0 [ 1.190219] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 1.197167] at24 2-0054: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.204491] at24 2-0055: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.211753] at24 2-0056: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.218971] at24 2-0057: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.226012] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz [ 1.238199] bone_capemgr bone_capemgr: Baseboard: 'A335BNLT,00C0,4815BBBK1EA8' [ 1.245592] bone_capemgr bone_capemgr: compatible-baseboard=ti,beaglebone-black - #slots=4 [ 1.309192] bone_capemgr bone_capemgr: slot #0: No cape found [ 1.389188] bone_capemgr bone_capemgr: slot #1: No cape found [ 1.449187] bone_capemgr bone_capemgr: slot #2: No cape found [ 1.509186] bone_capemgr bone_capemgr: slot #3: No cape found [ 1.515077] bone_capemgr bone_capemgr: initialized OK. [ 1.520653] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:01 UTC (946684801) [ 1.545999] net eth0: initializing cpsw version 1.12 (0) [ 1.551474] net eth0: initialized cpsw ale version 1.4 [ 1.559122] net eth0: ALE Table size 1024 [ 1.639548] net eth0: phy found : id is : 0x7c0f1 [ 3.639903] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 3.669199] Sending DHCP requests ., OK [ 5.941955] IP-Config: Got DHCP answer from 172.16.16.1, my address is 172.16.16.14 [ 5.952272] IP-Config: Complete: [ 5.957879] device=eth0, hwaddr=ec:24:b8:9e:15:cc, ipaddr=172.16.16.14, mask=255.255.255.0, gw=172.16.16.1 [ 5.970478] host=172.16.16.14, domain=home.nileshgr.com, nis-domain=(none) [ 5.980279] bootserver=172.16.16.1, rootserver=172.16.16.1, rootpath= [ 5.987080] nameserver0=172.16.16.1 [ 5.996492] Waiting 5 sec before mounting root device... [ 11.010214] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities [ 11.021705] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities [ 11.037888] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 11.048585] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 11.067095] devtmpfs: mounted [ 11.072843] Freeing unused kernel memory: 232K (c048e000 - c04c8000) [ 11.319370] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro,data=ordered [ 11.900503] random: dd: uninitialized urandom read (512 bytes read, 25 bits of entropy available) [ 12.023092] random: dropbear: uninitialized urandom read (32 bytes read, 27 bits of entropy available) [ 41.829893] bone_capemgr bone_capemgr: part_number 'DVK530-LCD4-01-00A0', version 'N/A' [ 41.841336] bone_capemgr bone_capemgr: slot #4: override [ 41.849840] bone_capemgr bone_capemgr: Using override eeprom data at slot 4 [ 41.859965] bone_capemgr bone_capemgr: slot #4: 'Override Board Name,00A0,Override Manuf,DVK530-LCD4-01-0' [ 51.969219] random: nonblocking pool is initialized