Problem seen in run Android (eclair) on an SMDK6410
david
on an SMDK6410:
=================================================================================
U-BOOT# nand read 50008000 600000 300000;nand read 50800000 900000
100000;bootm 50008000 50800000
NAND read: device 0 offset 0x6291456, size 0x3145728
3145728 bytes read: OK
NAND read: device 0 offset 0x9437184, size 0x1048576
1048576 bytes read: OK
Boot with zImage
do not support this address : 50008000
get_format
-------- 1 --------
## Loading init Ramdisk from Legacy Image at 50800000 ...
Image Name: ramdisk
Created: 2010-02-12 5:54:20 UTC
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 159996 Bytes = 156.2 kB
Load Address: 50800000
Entry Point: 50800000
Verifying Checksum ... OK
Starting kernel ...
Uncompressing
Linux..............................................................................................................................
done, booting the kernel.
[ 0.000000] Linux version 2.6.29 (hskang@hskang-desktop) (gcc
version 4.3.1 (for S3C64XX Samsung Electronics AP Development Team) )
#1 Fri Feb 12 14:20:27 KST 2010
[ 0.000000] CPU: ARMv6-compatible processor [410fb766] revision 6
(ARMv7), cr=00c5307f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing
instruction cache
[ 0.000000] Machine: SMDK6410
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] Ignoring unrecognised tag 0x41001099
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU S3C6410 (id 0x36410101)
[ 0.000000] S3C Clocks, (c) 2004 Simtec Electronics
[ 0.000000] S3C64XX: PLL settings, A=532000000, M=532000000,
E=24000000
[ 0.000000] S3C64XX: HCLKx2=266000000, HCLK=133000000,
PCLK=66500000
[ 0.000000] mout_apll: source is fout_apll (1), rate is 532000000
[ 0.000000] mout_epll: source is fout_epll (1), rate is 24000000
[ 0.000000] mout_mpll: source is mpll (1), rate is 532000000
[ 0.000000] mmc_bus: source is dout_mpll (1), rate is 266000000
[ 0.000000] mmc_bus: source is dout_mpll (1), rate is 266000000
[ 0.000000] mmc_bus: source is dout_mpll (1), rate is 266000000
[ 0.000000] usb-host-bus: source is mout_epll (0), rate is 24000000
[ 0.000000] lcd: source is dout_mpll (1), rate is 266000000
[ 0.000000] uclk1: source is dout_mpll (1), rate is 66500000
[ 0.000000] spi_epll: source is mout_epll (0), rate is 24000000
[ 0.000000] spi_epll: source is mout_epll (0), rate is 24000000
[ 0.000000] sclk_audio0: source is mout_epll (0), rate is 24000000
[ 0.000000] sclk_audio1: source is mout_epll (0), rate is 24000000
[ 0.000000] sclk_audio2: source is mout_epll (0), rate is 24000000
[ 0.000000] irda-bus: source is mout_epll (0), rate is 24000000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 21336
[ 0.000000] Kernel command line: console=ttySAC0,115200
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000446] Console: colour dummy device 80x30
[ 0.000614] console [ttySAC0] enabled
[ 0.180467] Dentry cache hash table entries: 16384 (order: 4, 65536
bytes)
[ 0.187935] Inode-cache hash table entries: 8192 (order: 3, 32768
bytes)
[ 0.202454] Memory: 84MB = 84MB total
[ 0.202516] Memory: 80276KB available (3588K code, 946K data, 152K
init)
[ 0.208181] Calibrating delay loop... 132.71 BogoMIPS (lpj=331776)
[ 0.320602] Mount-cache hash table entries: 512
[ 0.322427] CPU: Testing write buffer coherency: ok
[ 0.329687] net_namespace: 520 bytes
[ 0.332209] NET: Registered protocol family 16
[ 0.352160] S3C6410 Power Management, (c) 2008 Samsung Electronics
[ 0.352920] S3C6410: Initialising architecture
[ 0.357242] S3C DMA-pl080 Controller Driver, (c) 2006-2007 Samsung
Electronics
[ 0.364523] Total 32 DMA channels will be initialized.
[ 0.373121] GPIO-155 autorequested
[ 0.373166] GPIO-156 autorequested
[ 0.376394] GPIO-157 autorequested
[ 0.379593] GPIO-158 autorequested
[ 0.383012] GPIO-159 autorequested
[ 0.386380] GPIO-129 autorequested
[ 0.389734] GPIO-130 autorequested
[ 0.393139] GPIO-131 autorequested
[ 0.439668] bio: create slab <bio-0> at 0
[ 0.453902] NET: Registered protocol family 2
[ 0.454251] IP route cache hash table entries: 1024 (order: 0, 4096
bytes)
[ 0.460754] TCP established hash table entries: 4096 (order: 3,
32768 bytes)
[ 0.467000] TCP bind hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.473216] TCP: Hash tables configured (established 4096 bind
4096)
[ 0.479289] TCP reno registered
[ 0.482845] NET: Registered protocol family 1
[ 0.487722] checking if image is initramfs... it is
[ 0.593806] Freeing initrd memory: 156K
[ 0.594752] S3C PWM Driver, (c) 2006-2007 Samsung Electronics
[ 0.598249] NetWinder Floating Point Emulator V0.97 (double
precision)
[ 0.611245] ashmem: initialized
[ 0.613900] yaffs Feb 12 2010 14:19:57 Installing.
[ 0.614035] msgmni has been set to 157
[ 0.619048] alg: No test for stdrng (krng)
[ 0.621637] io scheduler noop registered
[ 0.625444] io scheduler anticipatory registered (default)
[ 0.630831] io scheduler deadline registered
[ 0.635277] io scheduler cfq registered
[ 0.639642] S3C_LCD clock got enabled :: 266.000 Mhz
[ 0.650071] LCD TYPE :: LTE480WV will be initialized
[ 0.777005] Window[0] - FB1: map_video_memory: clear
ff000000:00177000
[ 0.782868] FB1: map_video_memory: dma=54e00000
cpu=ff000000 size=00177000
[ 0.785842] Window[0] - FB2: map_video_memory: clear
ff0bb800:000bb800
[ 0.792339] FB2: map_video_memory: dma=54ebb800
cpu=ff0bb800 size=000bb800
[ 0.813949] Console: switching to colour frame buffer device 100x30
[ 0.826209] fb0: s3cfb frame buffer device
[ 0.838044] Window[1] - FB1: map_video_memory: clear
ff177000:00177000
[ 0.844575] FB1: map_video_memory: dma=55000000
cpu=ff177000 size=00177000
[ 0.846901] Window[1] - FB2: map_video_memory: clear
ff232800:000bb800
[ 0.853398] FB2: map_video_memory: dma=550bb800
cpu=ff232800 size=000bb800
[ 0.862111] fb1: s3cfb frame buffer device
[ 0.865960] SMDK board LCD Backlight Device Driver (c) 2008 Samsung
Electronics
[ 0.873533] Registered led device: lcd-backlight
[ 1.494304] lp: driver loaded but no devices found
[ 1.494364] S3C64XX ADC driver, (c) 2007 Samsung Electronics
[ 1.499432] ADC platform data read
[ 1.503606] S3C64XX ADC driver successfully probed !
[ 1.508967] ppdev: user-space parallel port driver
[ 1.512588] s3c64xx-uart.0: s3c_serial0 at MMIO 0x7f005000 (irq =
16) is a S3C64XX
[ 1.521544] s3c64xx-uart.1: s3c_serial1 at MMIO 0x7f005400 (irq =
20) is a S3C64XX
[ 1.529078] s3c64xx-uart.2: s3c_serial2 at MMIO 0x7f005800 (irq =
24) is a S3C64XX
[ 1.536741] s3c64xx-uart.3: s3c_serial3 at MMIO 0x7f005c00 (irq =
28) is a S3C64XX
[ 1.566775] brd: module loaded
[ 1.578258] loop: module loaded
[ 1.578434] pmem: 1 init
[ 1.580269] pmem_render: 0 init
[ 1.582690] pmem_stream: 0 init
[ 1.585924] pmem_stream2: 0 init
[ 1.588946] pmem_preview: 0 init
[ 1.592360] pmem_picture: 0 init
[ 1.595561] pmem_jpeg: 0 init
[ 1.598833] Linux video capture interface: v2.00
[ 1.610145] Request irq 35 for codec
[ 1.610214] Request irq 36 for preview
[ 1.614018] S3C FIMC v3.0
[ 1.616930] S3C G2D Init : Done
[ 1.617725] S3C G3D Driver, (c) 2007-2009 Samsung Electronics
[ 1.625220] s3c_g3d version : 0x1050000
[ 1.627273] G3D_RESERVED_MEM_SIZE : 24 MB
[ 1.631307] G3D_CHUNK_SIZE : 2 MB
[ 1.634540] G3D_CHUNK_NUM : 12 (UI_CHUNK:4)
[ 1.638813] 0 th virt_addr = 0xc6800000, phy_addr = 0x56800000
[ 1.644567] 1 th virt_addr = 0xc6a00000, phy_addr = 0x56a00000
[ 1.650366] 2 th virt_addr = 0xc6c00000, phy_addr = 0x56c00000
[ 1.656169] 3 th virt_addr = 0xc6e00000, phy_addr = 0x56e00000
[ 1.661971] 4 th virt_addr = 0xc7000000, phy_addr = 0x57000000
[ 1.667778] 5 th virt_addr = 0xc7200000, phy_addr = 0x57200000
[ 1.673589] 6 th virt_addr = 0xc7400000, phy_addr = 0x57400000
[ 1.679394] 7 th virt_addr = 0xc7600000, phy_addr = 0x57600000
[ 1.685211] 8 th virt_addr = 0xc7800000, phy_addr = 0x57800000
[ 1.691010] 9 th virt_addr = 0xc7a00000, phy_addr = 0x57a00000
[ 1.696837] 10 th virt_addr = 0xc7c00000, phy_addr = 0x57c00000
[ 1.702723] 11 th virt_addr = 0xc7e00000, phy_addr = 0x57e00000
[ 1.709261] S3C6400 MFC Driver, (c) 2007 Samsung Electronics
[ 1.719156] S3C6400 MFC driver module init OK.
[ 1.719215] S3C PostProcessor Driver v3.12, (c) 2009 Samsung
Electronics
[ 1.727251] S3C JPEG Driver, (c) 2007 Samsung Electronics
[ 1.733814] S3C CMM Driver, (c) 2008 Samsung Electronics
[ 1.738130] S3C NAND Driver, (c) 2008 Samsung Electronics
[ 1.742845] S3C NAND Driver is using hardware ECC.
[ 1.746223] NAND device: Manufacturer ID: 0xad, Chip ID: 0xda
(Hynix NAND 256MiB 3,3V 8-bit)
[ 1.754656] Creating 7 MTD partitions on "NAND 256MiB 3,3V 8-bit":
[ 1.760746] 0x0000000c0000-0x000000100000 : "misc"
[ 1.769443] 0x000000100000-0x000000600000 : "recovery"
[ 1.774750] 0x000000600000-0x000000900000 : "kernel"
[ 1.779433] 0x000000900000-0x000000a00000 : "ramdisk"
[ 1.784054] 0x000000a00000-0x000004d00000 : "system"
[ 1.801199] 0x000004d00000-0x000009000000 : "cache"
[ 1.817023] 0x000009000000-0x000010000000 : "userdata"
[ 1.841549] [S3C USB-OTG MODE] : DMA
[ 1.843850] [ADB_UMS] string_dev = S3C6410_Android
[ 1.844363] mass_storage_function_add
[ 1.850129] android_usb gadget: Number of LUNs=1
[ 1.852623] adb_function_add
[ 1.856759] android_usb gadget: Android Composite USB, version: Feb
12 2010
[ 1.862480] android_usb gadget: android_usb ready
[ 1.867212] Registered gadget driver 'android_usb'
[ 1.874098] mice: PS/2 mouse device common for all mice
[ 1.878646] input: s3c-keypad-rev0000 as /class/input/input0
[ 1.884404] s3c-keypad Initialized
[ 1.886645] S3C Keypad Driver
[ 1.889025] S3C Touchscreen driver, (c) 2009 Samsung Electronics
[ 1.895432] S3C TouchScreen got loaded successfully : 12 bits
[ 1.902697] input: S3C TouchScreen as /class/input/input1
[ 1.910725] S3C RTC, (c) 2004,2006 Simtec Electronics
[ 1.911681] i2c /dev entries driver
[ 1.916470] s3c-i2c s3c-i2c.0: slave address 0x10
[ 1.919283] s3c-i2c s3c-i2c.0: bus frequency set to 377 KHz
[ 1.927824] s3c-i2c s3c-i2c.0: i2c-0: S3C I2C adapter
[ 1.930005] s3c-i2c s3c-i2c.1: slave address 0x10
[ 1.934612] s3c-i2c s3c-i2c.1: bus frequency set to 377 KHz
[ 1.943276] s3c-i2c s3c-i2c.1: i2c-1: S3C I2C adapter
[ 1.946092] s3c_bat_init
[ 1.947793] smdk6410-battery smdk6410-battery: s3c_bat_probe
[ 1.957284] cpuidle: using governor ladder
[ 1.957344] cpuidle: using governor menu
[ 1.962366] sdhci: Samsung S3C6410 SD/MMC driver
[ 1.966506] s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133000000
Hz)
[ 1.972557] s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133000000
Hz)
[ 1.979064] s3c-sdhci s3c-sdhci.1: clock source 2: hsmmc (133000000
Hz)
[ 1.987016] Registered led device: mmc0
[ 1.990095] mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.1]
using DMA
[ 2.000727] logger: created 64K log 'log_main'
[ 2.001920] logger: created 256K log 'log_events'
[ 2.007056] logger: created 64K log 'log_radio'
[ 2.011798] Advanced Linux Sound Architecture Driver Version
1.0.18a.
[ 2.022461] No device for DAI WM8580 PAIFRX
[ 2.022520] No device for DAI WM8580 PAIFTX
[ 2.025754] No device for DAI s3c-i2s
[ 2.033010] WM8580 Audio Codec 0.1
[ 2.035551] asoc: WM8580 PAIFRX <-> s3c-i2s mapping ok
[ 2.046268] ALSA device list:
[ 2.046316] #0: smdk6410 (WM8580)
[ 2.047360] TCP cubic registered
[ 2.050371] NET: Registered protocol family 17
[ 2.054781] NET: Registered protocol family 15
[ 2.059948] RPC: Registered udp transport module.
[ 2.063890] RPC: Registered tcp transport module.
[ 2.069026] VFP support v0.3: implementor 41 architecture 1 part 20
variant b rev 5
[ 2.080683] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 2.082514] Freeing init memory: 152K
[ 2.494203] [s3c_udc_cable_connect]
[ 2.494287] android_usb gadget: high speed config #1: UMS Only (Not
debugging mode)
[ 3.250536] init: cannot open '/initlogo.rle'
[ 3.278941] yaffs: dev is 32505860 name is "mtdblock4"
[ 3.278994] yaffs: passed flags ""
[ 3.281923] yaffs: Attempting MTD mount on 31.4, "mtdblock4"
[ 3.344873] yaffs_read_super: isCheckpointed 0
[ 3.346780] yaffs: dev is 32505862 name is "mtdblock6"
[ 3.348807] yaffs: passed flags ""
[ 3.352348] yaffs: Attempting MTD mount on 31.6, "mtdblock6"
[ 3.453357] yaffs_read_super: isCheckpointed 0
[ 3.454232] **>> yaffs chunk 64 was not erased
[ 3.457818] **>> yaffs write required 2 attempts
[ 3.468103] yaffs: dev is 32505861 name is "mtdblock5"
[ 3.468154] yaffs: passed flags ""
[ 3.471100] yaffs: Attempting MTD mount on 31.5, "mtdblock5"
[ 3.533908] yaffs_read_super: isCheckpointed 0
[ 3.590445] init: cannot find '/system/bin/sh', disabling 'console'
[ 3.591147] init: cannot find '/system/bin/servicemanager',
disabling 'servicemanager'
[ 3.599118] init: cannot find '/system/bin/vold', disabling 'vold'
[ 3.605671] init: cannot find '/system/bin/debuggerd', disabling
'debuggerd'
[ 3.612281] init: cannot find '/system/bin/rild', disabling 'ril-
daemon'
[ 3.618941] init: cannot find '/system/bin/app_process', disabling
'zygote'
[ 3.626296] init: cannot find '/system/bin/mediaserver', disabling
'media'
[ 3.632731] init: cannot find '/system/bin/dbus-daemon', disabling
'dbus'
[ 3.639499] init: cannot find '/system/bin/installd', disabling
'installd'
[ 3.646749] init: cannot find '/system/bin/keystore', disabling
'keystore'
[ 3.658961] [adb_function_enable] adb_function => (enabled)
Deva R
root file system and especially '/system' is gone for toss, after
mounting yaffs file system to '/'
NAND yaffs file system is mounted in your init.rc, and it should be
like below sequence.. to set '/system' and '/data' properly..
mount yaffs2 mtd@system /system
mount yaffs2 mtd@system /system ro remount
mount yaffs2 mtd@userdata /data nosuid nodev
mount yaffs2 mtd@cache /cache nosuid nodev
if any issue there in mounting, services that are to be run after
parsing init.rc will fail, as you see in the log..
> --
> unsubscribe: android-porti...@googlegroups.com
> website: http://groups.google.com/group/android-porting
>
> To unsubscribe from this group, send email to android-porting+unsubscribegooglegroups.com or reply to this email with the words "REMOVE ME" as the subject.
>
david
Changes made and no differences seen from retest.
I am wondering whether I have to change access right (chmod) to the
root files (in the images) or not?
Regards
David
On 24 Mar, 17:58, Deva R <r.deva...@gmail.com> wrote:
> have you modified init.rc from the prebuilt package?
>
> root file system and especially '/system' is gone for toss, after
> mounting yaffs file system to '/'
>
> NAND yaffs file system is mounted in your init.rc, and it should be
> like below sequence.. to set '/system' and '/data' properly..
>
> mount yaffs2 mtd@system /system
> mount yaffs2 mtd@system /system ro remount
> mount yaffs2 mtd@userdata /data nosuid nodev
> mount yaffs2 mtd@cache /cache nosuid nodev
>
> if any issue there in mounting, services that are to be run after
> parsing init.rc will fail, as you see in the log..
>
>
>
> On Wed, Mar 24, 2010 at 3:18 PM, david <dajun.c...@gmail.com> wrote:
> > Problem seen in running Android Eclair (prebuild images from Samsung)
> > on an SMDK6410:
>
> > =================================================================================
>
> > U-BOOT# nand read 50008000 600000 300000;nand read 50800000 900000
> > 100000;bootm 50008000 50800000
>
> > NAND read: device 0 offset 0x6291456, size 0x3145728
>
> > 3145728 bytes read: OK
>
> > NAND read: device 0 offset 0x9437184, size 0x1048576
>
> > 1048576 bytes read: OK
>
> > Boot with zImage
>
> > do not support this address : 50008000
>
> > get_format
>
> > -------- 1 --------
>
> > ## Loading init Ramdisk from Legacy Image at 50800000 ...
>
> > Image Name: ramdisk
>
> > Created: 2010-02-12 5:54:20 UTC
>
> > Image Type: ARM Linux RAMDisk Image (uncompressed)
>
> > Data Size: 159996 Bytes = 156.2 kB
>
> > Load Address: 50800000
>
> > Entry Point: 50800000
>
> > Verifying Checksum ... OK
>
> > Starting kernel ...
>
> > Uncompressing
> > Linux..............................................................................................................................
> ...
>
> read more »- Hide quoted text -
>
> - Show quoted text -
supermaximus79
> ...
>
> read more »
david
David
supermaximus79
Could you tell me, where did you get 2.6.29 kernel for smdk6410?
Because official Samsung's 2.6.29 kernel doesn't support
smdk6410_defconfig.
Regards!
> ...
>
> read more »