mv_xor f1060900.xor: Marvell shared XOR driver
mv_xor f1060900.xor: Marvell XOR: ( xor cpy )
mv_xor f1060900.xor: Marvell XOR: ( xor fill cpy )
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
brd: module loaded
loop: module loaded
sata_mv f1080000.sata: version 1.28
sata_mv f1080000.sata: slots 32 ports 2
scsi0 : sata_mv
scsi1 : sata_mv
ata1: SATA max UDMA/133 irq 21
ata2: SATA max UDMA/133 irq 21
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
Scanning device for bad blocks
Bad eraseblock 101 at 0x000000ca0000
Bad eraseblock 932 at 0x000007480000
6 ofpart partitions found on MTD device orion_nand
Creating 6 MTD partitions on "orion_nand":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000600000 : "uImage"
0x000000600000-0x000000b00000 : "ramdisk"
0x000000b00000-0x000007100000 : "image"
0x000007100000-0x000007b00000 : "mini firmware"
0x000007b00000-0x000008000000 : "config"
libphy: orion_mdio_bus: probed
mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:50:43:00:2e:02
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-orion: EHCI orion driver
orion-ehci f1050000.ehci: EHCI Host Controller
orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
orion-ehci f1050000.ehci: irq 19, io mem 0xf1050000
orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usbcore: registered new interface driver usb-storage
rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0
i2c /dev entries driver
gpio-fan gpio_fan.2: GPIO fan initialized
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
cpuidle: using governor ladder
cpuidle: using governor menu
leds-gpio gpio-leds.5: pins are not configured from the driver
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP: cubic registered
NET: Registered protocol family 17
SATA0 Power: 5000 mV 
SATA1 Power: 5000 mV 
input: gpio_keys.1 as /devices/gpio_keys.1/input/input0
rtc-mv f1010300.rtc: setting system clock to 2016-04-02 06:01:05 UTC (1459576865)
usb 1-1: new high-speed USB device number 2 using orion-ehci
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
ata1.00: ATA-9: WDC WD30EZRX-19D8PB0, 81.00A81, max UDMA/133
ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      WDC WD30EZRX-19D 81.0 PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
sd 0:0:0:0: [sda] 4096-byte physical blocks
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
usb-storage 1-1:1.0: USB Mass Storage device detected
scsi2 : usb-storage 1-1:1.0
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
ata2.00: ATA-9: WDC WD30EZRX-19D8PB0, 81.00A81, max UDMA/133
ata2.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access     ATA      WDC WD30EZRX-19D 81.0 PQ: 0 ANSI: 5
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
sd 1:0:0:0: [sdb] 4096-byte physical blocks
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 2:0:0:0: Direct-Access     WD       My Passport 082A 1012 PQ: 0 ANSI: 6
sd 2:0:0:0: Attached scsi generic sg2 type 0
scsi 2:0:0:1: Enclosure         WD       SES Device       1012 PQ: 0 ANSI: 6
scsi 2:0:0:1: Attached scsi generic sg3 type 13
sd 2:0:0:0: [sdc] Very big device. Trying to use READ CAPACITY(16).
sd 2:0:0:0: [sdc] 5860466688 512-byte logical blocks: (3.00 TB/2.72 TiB)
sd 2:0:0:0: [sdc] 4096-byte physical blocks
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 47 00 10 08
sd 2:0:0:0: [sdc] No Caching mode page found
sd 2:0:0:0: [sdc] Assuming drive cache: write through
sd 2:0:0:0: [sdc] Very big device. Trying to use READ CAPACITY(16).
sd 2:0:0:0: [sdc] No Caching mode page found
sd 2:0:0:0: [sdc] Assuming drive cache: write through
 sdb: sdb1 sdb2
sd 1:0:0:0: [sdb] Attached SCSI disk
 sdc: sdc1 sdc2
sd 2:0:0:0: [sdc] Very big device. Trying to use READ CAPACITY(16).
sd 2:0:0:0: [sdc] No Caching mode page found
sd 2:0:0:0: [sdc] Assuming drive cache: write through
sd 2:0:0:0: [sdc] Attached SCSI disk
md: Skipping autodetection of RAID arrays. (raid=autodetect will force)
RAMDISK: squashfs filesystem found at block 0
RAMDISK: Loading 2982KiB [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-done.
VFS: Mounted root (squashfs filesystem) readonly on device 1:0.
Freeing unused kernel memory: 172K (c0468000 - c0493000)
Adding 292964k swap on /dev/sda1.  Priority:1 extents:1 across:292964k 
md: bind<sda2>
Adding 292964k swap on /dev/sdb1.  Priority:1 extents:1 across:292964k 
md: bind<sdb2>
md: bind<sdc2>
md/raid:md0: device sdc2 operational as raid disk 2
md/raid:md0: device sdb2 operational as raid disk 1
md/raid:md0: device sda2 operational as raid disk 0
md/raid:md0: allocated 3198kB
md/raid:md0: raid level 5 active with 3 out of 3 devices, algorithm 2
RAID conf printout:
 --- level:5 rd:3 wd:3
 disk 0, o:1, dev:sda2
 disk 1, o:1, dev:sdb2
 disk 2, o:1, dev:sdc2
created bitmap (22 pages) for device md0
EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
md0: bitmap initialized from disk: read 2 pages, set 0 of 44708 bits
md0: detected capacity change from 0 to 6000585211904
 md0: unknown partition table
mv643xx_eth_port mv643xx_eth_port.0 eth0: link down
usbcore: registered new interface driver usblp
mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled
EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null)
usb 1-1: reset high-speed USB device number 2 using orion-ehci
usb 1-1: reset high-speed USB device number 2 using orion-ehci
usb 1-1: reset high-speed USB device number 2 using orion-ehci
usb 1-1: reset high-speed USB device number 2 using orion-ehci
usb 1-1: reset high-speed USB device number 2 using orion-ehci
usb 1-1: reset high-speed USB device number 2 using orion-ehci
usb 1-1: reset high-speed USB device number 2 using orion-ehci
usb 1-1: reset high-speed USB device number 2 using orion-ehci
usb 1-1: device descriptor read/64, error -110
usb 1-1: device descriptor read/64, error -110
usb 1-1: reset high-speed USB device number 2 using orion-ehci
usb 1-1: device descriptor read/64, error -110
usb 1-1: device descriptor read/64, error -110
usb 1-1: reset high-speed USB device number 2 using orion-ehci
usb 1-1: device not accepting address 2, error -110
usb 1-1: reset high-speed USB device number 2 using orion-ehci
usb 1-1: device not accepting address 2, error -110
usb 1-1: USB disconnect, device number 2
sd 2:0:0:0: Device offlined - not ready after error recovery
sd 2:0:0:0: [sdc] Unhandled error code
sd 2:0:0:0: [sdc]  
Result: hostbyte=0x01 driverbyte=0x00
sd 2:0:0:0: [sdc] CDB: 
cdb[0]=0x8a: 8a 00 00 00 00 00 ef ab 62 70 00 00 00 f0 00 00
end_request: I/O error, dev sdc, sector 4020986480
md/raid:md0: Disk failure on sdc2, disabling device.
md/raid:md0: Operation continuing on 2 devices.
md: super_written gets error=-5, uptodate=0
sd 2:0:0:0: [sdc] Unhandled error code
sd 2:0:0:0: [sdc]  
Result: hostbyte=0x01 driverbyte=0x00
sd 2:0:0:0: [sdc] CDB: 
cdb[0]=0x8a: 8a 00 00 00 00 00 ef ab 63 60 00 00 00 f0 00 00
end_request: I/O error, dev sdc, sector 4020986720
usb 1-1: new high-speed USB device number 3 using orion-ehci
RAID conf printout:
 --- level:5 rd:3 wd:2
 disk 0, o:1, dev:sda2
 disk 1, o:1, dev:sdb2
 disk 2, o:0, dev:sdc2
RAID conf printout:
 --- level:5 rd:3 wd:2
 disk 0, o:1, dev:sda2
 disk 1, o:1, dev:sdb2
Buffer I/O error on device sdc1, logical block 114689
lost page write due to I/O error on sdc1
JBD2: Error -5 detected when updating journal superblock for sdc1-8.
usb 1-1: device descriptor read/64, error -110
usb 1-1: device descriptor read/64, error -110
usb 1-1: new high-speed USB device number 4 using orion-ehci
usb 1-1: device descriptor read/64, error -110
usb 1-1: device descriptor read/64, error -110
usb 1-1: new high-speed USB device number 5 using orion-ehci
usb 1-1: device not accepting address 5, error -110
usb 1-1: new high-speed USB device number 6 using orion-ehci
usb 1-1: device not accepting address 6, error -110
hub 1-0:1.0: unable to enumerate USB device on port 1