Network And Data Communication
Ilona Brownson
Data communications refers to the transmission of this digital data between two or more computers and a computer network or data network is a telecommunications network that allows computers to exchange data. The physical connection between networked computing devices is established using either cable media or wireless media. The best-known computer network is the Internet.
A system of interconnected computers and computerized peripherals such as printers is called computer network. This interconnection among computers facilitates information sharing among them. Computers may connect to each other by either wired or wireless media.
Networking engineering is a complicated task, which involves software, firmware, chip level engineering, hardware, and electric pulses. To ease network engineering, the whole networking concept is divided into multiple layers. Each layer is involved in some particular task and is independent of all other layers. But as a whole, almost all networking tasks depend on all of these layers. Layers share data between them and they depend on each other only to take input and send output.
A network of networks is called an internetwork, or simply the internet. It is the largest network in existence on this planet.The internet hugely connects all WANs and it can have connection to LANs and Home networks. Internet uses TCP/IP protocol suite and uses IP as its addressing protocol. Present day, Internet is widely implemented using IPv4. Because of shortage of address spaces, it is gradually migrating from IPv4 to IPv6.
Internet enables its users to share and access enormous amount of information worldwide. It uses WWW, FTP, email services, audio and video streaming etc. At huge level, internet works on Client-Server model.
This tutorial has been prepared for the computer science graduates to help them understand the basic to advanced concepts related to Data Communication and Computer Networking. After completing this tutorial you will find yourself at a moderate level of expertise in Data Communication and Computer Networking from where you can take yourself to next levels.
Before you start proceeding with this tutorial, I'm making an assumption that you are already aware about basic computer concepts like what is keyboard, mouse, monitor, input, output, primary memory and secondary memory etc. If you are not well aware of these concepts then I will suggest to go through our short tutorial on Computer Fundamentals.
Data communication, including data transmission and data reception, is the transfer of data, transmitted and received over a point-to-point or point-to-multipoint communication channel. Examples of such channels are copper wires, optical fibers, wireless communication using radio spectrum, storage media and computer buses. The data are represented as an electromagnetic signal, such as an electrical voltage, radiowave, microwave, or infrared signal.
Analog transmission is a method of conveying voice, data, image, signal or video information using a continuous signal which varies in amplitude, phase, or some other property in proportion to that of a variable. The messages are either represented by a sequence of pulses by means of a line code (baseband transmission), or by a limited set of continuously varying waveforms (passband transmission), using a digital modulation method. The passband modulation and corresponding demodulation is carried out by modem equipment.
Digital communications, including digital transmission and digital reception, is the transfer of either a digitized analog signal or a born-digital bitstream.[1] According to the most common definition, both baseband and passband bit-stream components are considered part of a digital signal; an alternative definition considers only the baseband signal as digital, and passband transmission of digital data as a form of digital-to-analog conversion.
Digital transmission or data transmission traditionally belongs to telecommunications and electrical engineering. Basic principles of data transmission may also be covered within the computer science or computer engineering topic of data communications, which also includes computer networking applications and communication protocols, for example routing, switching and inter-process communication. Although the Transmission Control Protocol (TCP) involves transmission, TCP and other transport layer protocols are covered in computer networking but not discussed in a textbook or course about data transmission.
In most textbooks, the term analog transmission only refers to the transmission of an analog message signal (without digitization) by means of an analog signal, either as a non-modulated baseband signal or as a passband signal using an analog modulation method such as AM or FM. It may also include analog-over-analog pulse modulated baseband signals such as pulse-width modulation. In a few books within the computer networking tradition, analog transmission also refers to passband transmission of bit-streams using digital modulation methods such as FSK, PSK and ASK. Note that these methods are covered in textbooks named digital transmission or data transmission, for example.[1]
Data (mainly but not exclusively informational) has been sent via non-electronic (e.g. optical, acoustic, mechanical) means since the advent of communication. Analog signal data has been sent electronically since the advent of the telephone. However, the first data electromagnetic transmission applications in modern time were electrical telegraphy (1809) and teletypewriters (1906), which are both digital signals. The fundamental theoretical work in data transmission and information theory by Harry Nyquist, Ralph Hartley, Claude Shannon and others during the early 20th century, was done with these applications in mind.
In the early 1960s, Paul Baran invented distributed adaptive message block switching for digital communication of voice messages using switches that were low-cost electronics.[8][9] Donald Davies invented and implemented modern data communication during 1965-7, including packet switching, high-speed routers, communication protocols, hierarchical computer networks and the essence of the end-to-end principle.[10][11][12][13] Baran's work did not include routers with software switches and communication protocols, nor the idea that users, rather than the network itself, would provide the reliability.[14][15][16] Both were seminal contributions that influenced the development of computer networks.[17][18]
Data transmission is utilized in computers in computer buses and for communication with peripheral equipment via parallel ports and serial ports such as RS-232 (1969), FireWire (1995) and USB (1996). The principles of data transmission are also utilized in storage media for error detection and correction since 1951. The first practical method to overcome the problem of receiving data accurately by the receiver using digital code was the Barker code invented by Ronald Hugh Barker in 1952 and published in 1953.[19] Data transmission is utilized in computer networking equipment such as modems (1940), local area network (LAN) adapters (1964), repeaters, repeater hubs, microwave links, wireless network access points (1997), etc.
In telephone networks, digital communication is utilized for transferring many phone calls over the same copper cable or fiber cable by means of pulse-code modulation (PCM) in combination with time-division multiplexing (TDM) (1962). Telephone exchanges have become digital and software controlled, facilitating many value-added services. For example, the first AXE telephone exchange was presented in 1976. Digital communication to the end user using Integrated Services Digital Network (ISDN) services became available in the late 1980s. Since the end of the 1990s, broadband access techniques such as ADSL, Cable modems, fiber-to-the-building (FTTB) and fiber-to-the-home (FTTH) have become widespread to small offices and homes. The current tendency is to replace traditional telecommunication services with packet mode communication such as IP telephony and IPTV.
Transmitting analog signals digitally allows for greater signal processing capability. The ability to process a communications signal means that errors caused by random processes can be detected and corrected. Digital signals can also be sampled instead of continuously monitored. The multiplexing of multiple digital signals is much simpler compared to the multiplexing of analog signals. Because of all these advantages, because of the vast demand to transmit computer data and the ability of digital communications to do so and because recent advances in wideband communication channels and solid-state electronics have allowed engineers to realize these advantages fully, digital communications have grown quickly.
The digital revolution has also resulted in many digital telecommunication applications where the principles of data transmission are applied. Examples include second-generation (1991) and later cellular telephony, video conferencing, digital TV (1998), digital radio (1999), and telemetry.
Data transmission, digital transmission or digital communications is the transfer of data over a point-to-point or point-to-multipoint communication channel. Examples of such channels include copper wires, optical fibers, wireless communication channels, storage media and computer buses. The data are represented as an electromagnetic signal, such as an electrical voltage, radiowave, microwave, or infrared light.
While analog transmission is the transfer of a continuously varying analog signal over an analog channel, digital communication is the transfer of discrete messages over a digital or an analog channel. The messages are either represented by a sequence of pulses by means of a line code (baseband transmission), or by a limited set of continuously varying wave forms (passband transmission), using a digital modulation method. The passband modulation and corresponding demodulation (also known as detection) is carried out by modem equipment. According to the most common definition of a digital signal, both baseband and passband signals representing bit-streams are considered as digital transmission, while an alternative definition only considers the baseband signal as digital, and passband transmission of digital data as a form of digital-to-analog conversion.[citation needed]