Davis Vantage Pro 2 - ethernet blues....
331 views
Skip to first unread message
bus...@gmail.com
Jan 27, 2017, 2:35:46 PM1/27/17
to weewx-user
Hi,
I just found out that that the wview site hadn't been updated since 2014 so I tumbled upon weewx while looking around for alternatives that is actively maintained.
So I installed weewx in my debian box and copied the wview database over, got everything up and running in a short time. - A part from pulling data from the Davis box. I have the correct IP address and port number. The debian box can ping the Davis unit too. The wview daemon is stopped so it shouldn't interfere. But there seems to be no or at least broken communication. Under wview there was never any communication problems. Do I have to reset the Davis box in order to get it accept the weewx daemon? What can be the problem? Does it exist different drivers for Davis units? Thanks for comments!
Btw: Does it exist downloadable language packs somewhere, or does every user create their own?
regards Tor
Jan 27 20:27:04 intranet weewx[502]: engine: retrying...
Jan 27 20:27:04 intranet weewx[502]: engine: Using configuration file /etc/weewx/weewx.conf
Jan 27 20:27:04 intranet weewx[502]: engine: Initializing engine
Jan 27 20:27:04 intranet weewx[502]: engine: Loading station type Vantage (weewx.drivers.vantage)
Jan 27 20:27:04 intranet weewx[502]: vantage: driver version is 3.0.9
Jan 27 20:27:04 intranet weewx[502]: vantage: Opened up ethernet host 172.20.100.40 on port 22222. timeout=4.0, tcp_send_delay=0.5
Jan 27 20:27:05 intranet weewx[502]: vantage: gentle wake up of console successful
Jan 27 20:27:05 intranet weewx[502]: vantage: _setup; hardware type is 16
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.engine.StdTimeSynch
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.engine.StdTimeSynch
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.engine.StdConvert
Jan 27 20:27:09 intranet weewx[502]: engine: StdConvert target unit is 0x1
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.engine.StdConvert
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.engine.StdCalibrate
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.engine.StdCalibrate
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.engine.StdQC
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.engine.StdQC
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.wxservices.StdWXCalculate
Jan 27 20:27:09 intranet weewx[502]: wxcalculate: The following values will be calculated: barometer=prefer_hardware, windchill=prefer_hardware, dewpoint=prefer_hardware, appTemp=prefer_hardware, rainRate=prefer_hardware, windrun=prefer_hardware, heatindex=prefer_hardware, maxSolarRad=prefer_hardware, humidex=prefer_hardware, pressure=prefer_hardware, inDewpoint=prefer_hardware, ET=prefer_hardware, altimeter=prefer_hardware, cloudbase=prefer_hardware
Jan 27 20:27:09 intranet weewx[502]: wxcalculate: The following algorithms will be used for calculations: altimeter=aaNOAA, maxSolarRad=RS
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.wxservices.StdWXCalculate
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.engine.StdArchive
Jan 27 20:27:09 intranet weewx[502]: engine: Archive will use data binding wx_binding
Jan 27 20:27:09 intranet weewx[502]: engine: Record generation will be attempted in 'hardware'
Jan 27 20:27:09 intranet weewx[502]: engine: The archive interval in the configuration file (300) does not match the station hardware interval (1800).
Jan 27 20:27:09 intranet weewx[502]: engine: Using archive interval of 1800 seconds (specified by hardware)
Jan 27 20:27:09 intranet weewx[502]: engine: Use LOOP data in hi/low calculations: 1
Jan 27 20:27:09 intranet weewx[502]: engine: Using binding 'wx_binding' to database 'weewx.sdb'
Jan 27 20:27:09 intranet weewx[502]: manager: Starting backfill of daily summaries
Jan 27 20:27:09 intranet weewx[502]: manager: Daily summaries up to date
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.engine.StdArchive
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.restx.StdStationRegistry
Jan 27 20:27:09 intranet weewx[502]: restx: StationRegistry: Registration not requested.
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.restx.StdStationRegistry
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.restx.StdWunderground
Jan 27 20:27:09 intranet weewx[502]: restx: Wunderground: Posting not enabled.
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.restx.StdWunderground
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.restx.StdPWSweather
Jan 27 20:27:09 intranet weewx[502]: restx: PWSweather: Posting not enabled.
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.restx.StdPWSweather
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.restx.StdCWOP
Jan 27 20:27:09 intranet weewx[502]: restx: CWOP: Posting not enabled.
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.restx.StdCWOP
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.restx.StdWOW
Jan 27 20:27:09 intranet weewx[502]: restx: WOW: Posting not enabled.
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.restx.StdWOW
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.restx.StdAWEKAS
Jan 27 20:27:09 intranet weewx[502]: restx: AWEKAS: Posting not enabled.
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.restx.StdAWEKAS
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.engine.StdPrint
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.engine.StdPrint
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.engine.StdReport
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.engine.StdReport
Jan 27 20:27:09 intranet weewx[502]: engine: Starting up weewx version 3.6.2
Jan 27 20:27:09 intranet weewx[502]: vantage: gentle wake up of console successful
Jan 27 20:27:10 intranet weewx[502]: engine: Clock error is -1.64 seconds (positive is fast)
Jan 27 20:27:10 intranet weewx[502]: vantage: Getting archive packets since 2017-01-27 20:00:00 CET (1485543600)
Jan 27 20:27:11 intranet weewx[502]: vantage: gentle wake up of console successful
Jan 27 20:27:12 intranet weewx[502]: vantage: Retrieving 0 page(s); starting index= 0
Jan 27 20:27:12 intranet weewx[502]: engine: Starting main packet loop.
Jan 27 20:27:17 intranet weewx[502]: vantage: ip-read error: timed out
Jan 27 20:27:17 intranet weewx[502]: vantage: retry #0 failed
Jan 27 20:27:17 intranet weewx[502]: vantage: gentle wake up of console successful
Jan 27 20:27:18 intranet weewx[502]: vantage: Requesting 200 LOOP packets.
Jan 27 20:27:18 intranet weewx[502]: vantage: gentle wake up of console successful
Jan 27 20:28:01 intranet CRON[23933]: (root) CMD (/usr/local/sbin/weather-push-www)
Jan 27 20:28:01 intranet CRON[23934]: (root) CMD (/opt/dashboard_backend/backend.sh)
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-read error: timed out
Jan 27 20:28:04 intranet weewx[502]: vantage: LOOP try #1; error: timed out
Jan 27 20:28:04 intranet weewx[502]: vantage: Requesting 200 LOOP packets.
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-read error: [Errno 104] Connection reset by peer
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #0 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #1 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #2 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #3 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: Unable to wake up console
Jan 27 20:28:04 intranet weewx[502]: vantage: LOOP try #2; error: Unable to wake up Vantage console
Jan 27 20:28:04 intranet weewx[502]: vantage: Requesting 200 LOOP packets.
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #0 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #1 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #2 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #3 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: Unable to wake up console
Jan 27 20:28:04 intranet weewx[502]: vantage: LOOP try #3; error: Unable to wake up Vantage console
Jan 27 20:28:04 intranet weewx[502]: vantage: Requesting 200 LOOP packets.
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #0 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #1 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #2 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #3 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: Unable to wake up console
Jan 27 20:28:04 intranet weewx[502]: vantage: LOOP try #4; error: Unable to wake up Vantage console
Jan 27 20:28:04 intranet weewx[502]: vantage: LOOP max tries (4) exceeded.
Jan 27 20:28:04 intranet weewx[502]: engine: Main loop exiting. Shutting engine down.
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: engine: Caught WeeWxIOError: Max tries exceeded while getting LOOP data.
Jan 27 20:28:04 intranet weewx[502]: **** Waiting 60 seconds then retrying...
test@intranet:~#
I just found out that that the wview site hadn't been updated since 2014 so I tumbled upon weewx while looking around for alternatives that is actively maintained.
So I installed weewx in my debian box and copied the wview database over, got everything up and running in a short time. - A part from pulling data from the Davis box. I have the correct IP address and port number. The debian box can ping the Davis unit too. The wview daemon is stopped so it shouldn't interfere. But there seems to be no or at least broken communication. Under wview there was never any communication problems. Do I have to reset the Davis box in order to get it accept the weewx daemon? What can be the problem? Does it exist different drivers for Davis units? Thanks for comments!
Btw: Does it exist downloadable language packs somewhere, or does every user create their own?
regards Tor
Jan 27 20:27:04 intranet weewx[502]: engine: retrying...
Jan 27 20:27:04 intranet weewx[502]: engine: Using configuration file /etc/weewx/weewx.conf
Jan 27 20:27:04 intranet weewx[502]: engine: Initializing engine
Jan 27 20:27:04 intranet weewx[502]: engine: Loading station type Vantage (weewx.drivers.vantage)
Jan 27 20:27:04 intranet weewx[502]: vantage: driver version is 3.0.9
Jan 27 20:27:04 intranet weewx[502]: vantage: Opened up ethernet host 172.20.100.40 on port 22222. timeout=4.0, tcp_send_delay=0.5
Jan 27 20:27:05 intranet weewx[502]: vantage: gentle wake up of console successful
Jan 27 20:27:05 intranet weewx[502]: vantage: _setup; hardware type is 16
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.engine.StdTimeSynch
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.engine.StdTimeSynch
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.engine.StdConvert
Jan 27 20:27:09 intranet weewx[502]: engine: StdConvert target unit is 0x1
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.engine.StdConvert
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.engine.StdCalibrate
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.engine.StdCalibrate
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.engine.StdQC
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.engine.StdQC
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.wxservices.StdWXCalculate
Jan 27 20:27:09 intranet weewx[502]: wxcalculate: The following values will be calculated: barometer=prefer_hardware, windchill=prefer_hardware, dewpoint=prefer_hardware, appTemp=prefer_hardware, rainRate=prefer_hardware, windrun=prefer_hardware, heatindex=prefer_hardware, maxSolarRad=prefer_hardware, humidex=prefer_hardware, pressure=prefer_hardware, inDewpoint=prefer_hardware, ET=prefer_hardware, altimeter=prefer_hardware, cloudbase=prefer_hardware
Jan 27 20:27:09 intranet weewx[502]: wxcalculate: The following algorithms will be used for calculations: altimeter=aaNOAA, maxSolarRad=RS
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.wxservices.StdWXCalculate
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.engine.StdArchive
Jan 27 20:27:09 intranet weewx[502]: engine: Archive will use data binding wx_binding
Jan 27 20:27:09 intranet weewx[502]: engine: Record generation will be attempted in 'hardware'
Jan 27 20:27:09 intranet weewx[502]: engine: The archive interval in the configuration file (300) does not match the station hardware interval (1800).
Jan 27 20:27:09 intranet weewx[502]: engine: Using archive interval of 1800 seconds (specified by hardware)
Jan 27 20:27:09 intranet weewx[502]: engine: Use LOOP data in hi/low calculations: 1
Jan 27 20:27:09 intranet weewx[502]: engine: Using binding 'wx_binding' to database 'weewx.sdb'
Jan 27 20:27:09 intranet weewx[502]: manager: Starting backfill of daily summaries
Jan 27 20:27:09 intranet weewx[502]: manager: Daily summaries up to date
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.engine.StdArchive
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.restx.StdStationRegistry
Jan 27 20:27:09 intranet weewx[502]: restx: StationRegistry: Registration not requested.
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.restx.StdStationRegistry
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.restx.StdWunderground
Jan 27 20:27:09 intranet weewx[502]: restx: Wunderground: Posting not enabled.
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.restx.StdWunderground
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.restx.StdPWSweather
Jan 27 20:27:09 intranet weewx[502]: restx: PWSweather: Posting not enabled.
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.restx.StdPWSweather
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.restx.StdCWOP
Jan 27 20:27:09 intranet weewx[502]: restx: CWOP: Posting not enabled.
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.restx.StdCWOP
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.restx.StdWOW
Jan 27 20:27:09 intranet weewx[502]: restx: WOW: Posting not enabled.
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.restx.StdWOW
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.restx.StdAWEKAS
Jan 27 20:27:09 intranet weewx[502]: restx: AWEKAS: Posting not enabled.
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.restx.StdAWEKAS
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.engine.StdPrint
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.engine.StdPrint
Jan 27 20:27:09 intranet weewx[502]: engine: Loading service weewx.engine.StdReport
Jan 27 20:27:09 intranet weewx[502]: engine: Finished loading service weewx.engine.StdReport
Jan 27 20:27:09 intranet weewx[502]: engine: Starting up weewx version 3.6.2
Jan 27 20:27:09 intranet weewx[502]: vantage: gentle wake up of console successful
Jan 27 20:27:10 intranet weewx[502]: engine: Clock error is -1.64 seconds (positive is fast)
Jan 27 20:27:10 intranet weewx[502]: vantage: Getting archive packets since 2017-01-27 20:00:00 CET (1485543600)
Jan 27 20:27:11 intranet weewx[502]: vantage: gentle wake up of console successful
Jan 27 20:27:12 intranet weewx[502]: vantage: Retrieving 0 page(s); starting index= 0
Jan 27 20:27:12 intranet weewx[502]: engine: Starting main packet loop.
Jan 27 20:27:17 intranet weewx[502]: vantage: ip-read error: timed out
Jan 27 20:27:17 intranet weewx[502]: vantage: retry #0 failed
Jan 27 20:27:17 intranet weewx[502]: vantage: gentle wake up of console successful
Jan 27 20:27:18 intranet weewx[502]: vantage: Requesting 200 LOOP packets.
Jan 27 20:27:18 intranet weewx[502]: vantage: gentle wake up of console successful
Jan 27 20:28:01 intranet CRON[23933]: (root) CMD (/usr/local/sbin/weather-push-www)
Jan 27 20:28:01 intranet CRON[23934]: (root) CMD (/opt/dashboard_backend/backend.sh)
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-read error: timed out
Jan 27 20:28:04 intranet weewx[502]: vantage: LOOP try #1; error: timed out
Jan 27 20:28:04 intranet weewx[502]: vantage: Requesting 200 LOOP packets.
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-read error: [Errno 104] Connection reset by peer
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #0 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #1 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #2 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #3 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: Unable to wake up console
Jan 27 20:28:04 intranet weewx[502]: vantage: LOOP try #2; error: Unable to wake up Vantage console
Jan 27 20:28:04 intranet weewx[502]: vantage: Requesting 200 LOOP packets.
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #0 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #1 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #2 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #3 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: Unable to wake up console
Jan 27 20:28:04 intranet weewx[502]: vantage: LOOP try #3; error: Unable to wake up Vantage console
Jan 27 20:28:04 intranet weewx[502]: vantage: Requesting 200 LOOP packets.
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #0 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #1 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #2 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: vantage: retry #3 failed
Jan 27 20:28:04 intranet weewx[502]: vantage: Unable to wake up console
Jan 27 20:28:04 intranet weewx[502]: vantage: LOOP try #4; error: Unable to wake up Vantage console
Jan 27 20:28:04 intranet weewx[502]: vantage: LOOP max tries (4) exceeded.
Jan 27 20:28:04 intranet weewx[502]: engine: Main loop exiting. Shutting engine down.
Jan 27 20:28:04 intranet weewx[502]: vantage: ip-write error: [Errno 32] Broken pipe
Jan 27 20:28:04 intranet weewx[502]: engine: Caught WeeWxIOError: Max tries exceeded while getting LOOP data.
Jan 27 20:28:04 intranet weewx[502]: **** Waiting 60 seconds then retrying...
test@intranet:~#
vince
Jan 27, 2017, 2:56:01 PM1/27/17
to weewx-user
On Friday, January 27, 2017 at 11:35:46 AM UTC-8, bus...@gmail.com wrote:
So I installed weewx in my debian box and copied the wview database over, got everything up and running in a short time. - A part from pulling data from the Davis box. I have the correct IP address and port number. The debian box can ping the Davis unit too. The wview daemon is stopped so it shouldn't interfere. But there seems to be no or at least broken communication. Under wview there was never any communication problems. Do I have to reset the Davis box in order to get it accept the weewx daemon? What can be the problem? Does it exist different drivers for Davis units? Thanks for comments!
We'd have to see your config file - see http://www.weewx.com/docs/utilities.htm#wee_debug_utility and run the utility and post the (obfuscated) config file please.
[...matthew/tom/gary - do we have a 'how to report a problem' wiki page ? I couldn't find one in a quick scan of the online wiki/docs....]
bus...@gmail.com
Jan 27, 2017, 3:10:07 PM1/27/17
to weewx-user
Using configuration file /etc/weewx/weewx.conf
Using database binding 'wx_binding', which is bound to database 'archive_sqlite'
System info
cpu cores: 2
bogomips: 4799.99
core id: 1
apicid: 1
fpu_exception: yes
stepping: 6
cache_alignment: 64
clflush size: 64
microcode: 0x36
cache size: 15360 KB
cpuid level: 10
fpu: yes
model name: Intel(R) Xeon(R) CPU E5-2620 v3 @ 2.40GHz
siblings: 2
physical id: 0
address sizes: 43 bits physical, 48 bits virtual
cpu family: 6
vendor_id: GenuineIntel
wp: yes
power management:
flags: fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts mmx fxsr sse sse2 ss ht syscall nx lm constant_tsc arch_perfmon pebs bts nopl tsc_reliable nonstop_tsc aperfmperf pni ssse3 cx16 sse4_1 tsc_deadline_timer hypervisor lahf_lm ida arat epb pln pts dtherm tsc_adjust
cpu MHz: 2399.998
model: 23
processor: 1
initial apicid: 1
Operating system: debian 8.7
Linux intranet 3.16.0-4-amd64 #1 SMP Debian 3.16.39-1 (2016-12-30) x86_64
1 minute load average: 0.00
5 minute load average: 0.02
15 minute load average: 0.06
General weewx info
Weewx version 3.6.2 detected.
Station info
Station type: Vantage
Driver: weewx.drivers.vantage
Driver info
[Vantage]
# This section is for the Davis Vantage series of weather stations.
# Connection type: serial or ethernet
# serial (the classic VantagePro)
# ethernet (the WeatherLinkIP)
type = ethernet
# If the connection type is serial, a port must be specified:
# Debian, Ubuntu, Redhat, Fedora, and SuSE:
# /dev/ttyUSB0 is a common USB port name
# /dev/ttyS0 is a common serial port name
# BSD:
# /dev/cuaU0 is a common serial port name
port = /dev/ttyUSB0
# If the connection type is ethernet, an IP Address/hostname is required:
host = 172.20.100.40
######################################################
# The rest of this section rarely needs any attention.
# You can safely leave it "as is."
######################################################
# Serial baud rate (usually 19200)
baudrate = 19200
# TCP port (when using the WeatherLinkIP)
tcp_port = 22222
# TCP send delay (when using the WeatherLinkIP):
tcp_send_delay = 0.5
# The id of your ISS station (usually 1). If you use a wind meter connected
# to a anemometer transmitter kit, use its id
iss_id = 1
# How long to wait for a response from the station before giving up (in
# seconds; must be greater than 2)
timeout = 4
# How long to wait before trying again (in seconds)
wait_before_retry = 1.2
# How many times to try before giving up:
max_tries = 4
# The driver to use:
driver = weewx.drivers.vantage
Currently installed extensions
No extensions installed
Archive info
Database name: weewx.sdb
Table name: archive
Unit system: 1 (US)
First good timestamp: 2009-02-26 14:30:00 CET (1235655000)
Last good timestamp: 2017-01-27 21:00:00 CET (1485547200)
Number of records: 138272
weewx (weewx.conf) is set to use an archive interval of 300 seconds.
The station hardware was not interrogated in determining archive interval.
Databases configured in weewx.conf
Database name: weewx.sdb
Database driver: weedb.sqlite
Database name: weewx
Database driver: weedb.mysql
Database host: localhost
Parsed and obfuscated weewx.conf
# WEEWX CONFIGURATION FILE
#
# Copyright (c) 2009-2015 Tom Keffer <tke...@gmail.com>
# See the file LICENSE.txt for your rights.
##############################################################################
# This section is for general configuration information.
# Set to 1 for extra debug info, otherwise comment it out or set to zero
debug = 1
# Root directory of the weewx data file hierarchy for this station
WEEWX_ROOT = /
# How long to wait before timing out a socket (FTP, HTTP) connection
socket_timeout = 20
# Do not modify this. It is used when installing and updating weewx.
version = 3.6.2
##############################################################################
# This section is for information about the station.
[Station]
# Description of the station location
location = Framnes KVGS
# Latitude and longitude in decimal degrees
latitude = 60.351
longitude = 6.182354
# Altitude of the station, with unit it is in. This is downloaded from
# from the station if the hardware supports it.
altitude = 28, meter
# Set to type of station hardware. There must be a corresponding stanza
# in this file with a 'driver' parameter indicating the driver to be used.
station_type = Vantage
# If you have a website, you may specify an URL
#station_url = http://www.example.com
# The start of the rain year (1=January; 10=October, etc.). This is
# downloaded from the station if the hardware supports it.
rain_year_start = 10
# Start of week (0=Monday, 6=Sunday)
week_start = 0
##############################################################################
[Vantage]
# This section is for the Davis Vantage series of weather stations.
# Connection type: serial or ethernet
# serial (the classic VantagePro)
# ethernet (the WeatherLinkIP)
type = ethernet
# If the connection type is serial, a port must be specified:
# Debian, Ubuntu, Redhat, Fedora, and SuSE:
# /dev/ttyUSB0 is a common USB port name
# /dev/ttyS0 is a common serial port name
# BSD:
# /dev/cuaU0 is a common serial port name
port = /dev/ttyUSB0
# If the connection type is ethernet, an IP Address/hostname is required:
host = 172.20.100.40
######################################################
# The rest of this section rarely needs any attention.
# You can safely leave it "as is."
######################################################
# Serial baud rate (usually 19200)
baudrate = 19200
# TCP port (when using the WeatherLinkIP)
tcp_port = 22222
# TCP send delay (when using the WeatherLinkIP):
tcp_send_delay = 0.5
# The id of your ISS station (usually 1). If you use a wind meter connected
# to a anemometer transmitter kit, use its id
iss_id = 1
# How long to wait for a response from the station before giving up (in
# seconds; must be greater than 2)
timeout = 4
# How long to wait before trying again (in seconds)
wait_before_retry = 1.2
# How many times to try before giving up:
max_tries = 4
# The driver to use:
driver = weewx.drivers.vantage
##############################################################################
# This section is for uploading data to Internet sites
[StdRESTful]
[[StationRegistry]]
# To register this weather station with weewx, set this to true
register_this_station = false
[[AWEKAS]]
# This section is for configuring posts to AWEKAS.
# If you wish to do this, set the option 'enable' to true,
# and specify a username and password.
enable = false
username = XXX obfuscated by wee_debug XXX
password = XXX obfuscated by wee_debug XXX
[[CWOP]]
# This section is for configuring posts to CWOP.
# If you wish to do this, set the option 'enable' to true,
# and specify the station ID (e.g., CW1234).
enable = false
station = XXX obfuscated by wee_debug XXX
# If this is an APRS (radio amateur) station, uncomment
# the following and replace with a passcode (e.g., 12345).
#passcode = replace_me (APRS stations only)
[[PWSweather]]
# This section is for configuring posts to PWSweather.com.
# If you wish to do this, set the option 'enable' to true,
# and specify a station and password.
enable = false
station = XXX obfuscated by wee_debug XXX
password = XXX obfuscated by wee_debug XXX
[[WOW]]
# This section is for configuring posts to WOW.
# If you wish to do this, set the option 'enable' to true,
# and specify a station and password.
enable = false
station = XXX obfuscated by wee_debug XXX
password = XXX obfuscated by wee_debug XXX
[[Wunderground]]
# This section is for configuring posts to the Weather Underground.
# If you wish to do this, set the option 'enable' to true,
# and specify a station (e.g., 'KORHOODR3') and password.
enable = false
station = XXX obfuscated by wee_debug XXX
password = XXX obfuscated by wee_debug XXX
# Set the following to True to have weewx use the WU "Rapidfire"
# protocol. Not all hardware can support it. See the User's Guide.
rapidfire = False
##############################################################################
# This section specifies what reports, using which skins, to generate.
[StdReport]
# Where the skins reside, relative to WEEWX_ROOT
SKIN_ROOT = /etc/weewx/skins
# Where the generated reports should go, relative to WEEWX_ROOT
HTML_ROOT = /var/www/html/weewx
# The database binding indicates which data should be used in reports.
data_binding = wx_binding
# Each of the following subsections defines a report that will be run.
[[StandardReport]]
# See the customizing guide to change the units, plot types and line
# colors, modify the fonts, display additional sensor data, and other
# customizations. Many of those changes can be made here by overriding
# parameters, or by modifying templates within the skin itself.
# The StandardReport uses the 'Standard' skin, which contains the
# images, templates and plots for the report.
skin = Standard
[[[Units]]]
[[[[Groups]]]]
group_altitude = meter
group_speed2 = meter_per_second2
group_pressure = mbar
group_rain = mm
group_rainrate = mm_per_hour
group_temperature = degree_C
group_degree_day = degree_C_day
group_speed = meter_per_second
[[FTP]]
# FTP'ing the results to a webserver is treated as just another report,
# albeit one with an unusual report generator!
skin = Ftp
# If you wish to use FTP, uncomment and fill out the next four lines.
#user = replace with the ftp username
#password = replace with the ftp password
#server = replace with the ftp server name, e.g, www.threefools.org
#path = replace with the ftp destination directory (e.g., /weather)
# Set to True for an FTP over TLS (FTPS) connection. Not all servers
# support this.
secure_ftp = False
# To upload files from something other than what HTML_ROOT is set
# to above, specify a different HTML_ROOT here.
#HTML_ROOT = /var/www/html/weewx
# Most FTP servers use port 21
port = 21
# Set to 1 to use passive mode, zero for active mode
passive = 1
[[RSYNC]]
# rsync'ing to a webserver is treated as just another report
skin = Rsync
# If you wish to use rsync, you must configure passwordless ssh using
# public/private key authentication from the user account that weewx
# runs as to the user account on the remote machine where the files
# will be copied.
#
# The following three lines determine where files will be sent.
#server = replace with the rsync server name, e.g, www.threefools.org
#path = replace with the rsync destination directory (e.g., /weather)
#user = replace with the rsync username
# Rsync can be configured to remove files from the remote server if
# they don't exist under HTML_ROOT locally. USE WITH CAUTION: if you
# make a mistake in the remote path, you could could unintentionally
# cause unrelated files to be deleted. Set to 1 to enable remote file
# deletion, zero to allow files to accumulate remotely.
delete = 0
##############################################################################
# This service acts as a filter, converting the unit system coming from
# the hardware to a unit system in the database.
[StdConvert]
# The target_unit affects only the unit system in the database. Once
# chosen it cannot be changed without converting the entire database.
# Modification of target_unit after starting weewx will result in
# corrupt data - the database will contain a mix of US and METRIC data.
#
# The value of target_unit does not affect the unit system for
# reporting - reports can display US, Metric, or any combination of units.
#
# In most cases, target_unit should be left as the default: US
#
# In particular, those migrating from a standard wview installation
# should use US since that is what the wview database contains.
# DO NOT MODIFY THIS VALUE UNLESS YOU KNOW WHAT YOU ARE DOING!
target_unit = US # Options are 'US', 'METRICWX', or 'METRIC'
##############################################################################
# This section can adjust data using calibration expressions.
[StdCalibrate]
[[Corrections]]
# For each type, an arbitrary calibration expression can be given.
# It should be in the units defined in the StdConvert section.
# Example:
foo = foo + 0.2
##############################################################################
# This section is for quality control checks. If units are not specified,
# values must be in the units defined in the StdConvert section.
[StdQC]
[[MinMax]]
barometer = 26, 32.5, inHg
outTemp = -40, 120, degree_F
inTemp = 10, 120, degree_F
outHumidity = 0, 100
inHumidity = 0, 100
windSpeed = 0, 120, mile_per_hour
pressure = 24, 34.5, inHg
##############################################################################
# This section controls the origin of derived values.
[StdWXCalculate]
[[Calculations]]
# Derived quantities are calculated by this service. Possible values are:
# hardware - use the value provided by hardware
# software - use the value calculated by weewx
# prefer_hardware - use value provide by hardware if available,
# otherwise use value calculated by weewx
pressure = prefer_hardware
barometer = prefer_hardware
altimeter = prefer_hardware
windchill = prefer_hardware
heatindex = prefer_hardware
dewpoint = prefer_hardware
inDewpoint = prefer_hardware
rainRate = prefer_hardware
##############################################################################
# For hardware that supports it, this section controls how often the
# onboard clock gets updated.
[StdTimeSynch]
# How often to check the weather station clock for drift (in seconds)
clock_check = 14400
# How much it can drift before we will correct it (in seconds)
max_drift = 5
##############################################################################
# This section is for configuring the archive service.
[StdArchive]
# If the station hardware supports data logging then the archive interval
# will be downloaded from the station. Otherwise, specify it (in seconds).
archive_interval = 300
# If possible, new archive records are downloaded from the station
# hardware. If the hardware does not support this, then new archive
# records will be generated in software.
# Set the following to "software" to force software record generation.
record_generation = hardware
# Whether to include LOOP data in hi/low statistics
loop_hilo = True
# The data binding used to save archive records
data_binding = wx_binding
##############################################################################
# This section binds a data store to a database.
[DataBindings]
[[wx_binding]]
# The database must match one of the sections in [Databases].
# This is likely to be the only option you would want to change.
database = archive_sqlite
# The name of the table within the database
table_name = archive
# The manager handles aggregation of data for historical summaries
manager = weewx.wxmanager.WXDaySummaryManager
# The schema defines the structure of the database.
# It is *only* used when the database is created.
schema = schemas.wview.schema
##############################################################################
# This section defines various databases.
[Databases]
# A SQLite database is simply a single file
[[archive_sqlite]]
database_type = SQLite
database_name = weewx.sdb
# MySQL
[[archive_mysql]]
database_type = MySQL
database_name = weewx
##############################################################################
# This section defines defaults for the different types of databases.
[DatabaseTypes]
# Defaults for SQLite databases
[[SQLite]]
driver = weedb.sqlite
# Directory in which the database files are located
SQLITE_ROOT = /var/lib/weewx
# Defaults for MySQL databases
[[MySQL]]
driver = weedb.mysql
# The host where the database is located
host = localhost
# The user name for logging in to the host
user = XXX obfuscated by wee_debug XXX
# The password for the user name
password = XXX obfuscated by wee_debug XXX
##############################################################################
# This section configures the internal weewx engine.
[Engine]
[[Services]]
# This section specifies the services that should be run. They are
# grouped by type, and the order of services within each group
# determines the order in which the services will be run.
prep_services = weewx.engine.StdTimeSynch
data_services = ,
process_services = weewx.engine.StdConvert, weewx.engine.StdCalibrate, weewx.engine.StdQC, weewx.wxservices.StdWXCalculate
archive_services = weewx.engine.StdArchive
restful_services = weewx.restx.StdStationRegistry, weewx.restx.StdWunderground, weewx.restx.StdPWSweather, weewx.restx.StdCWOP, weewx.restx.StdWOW, weewx.restx.StdAWEKAS
report_services = weewx.engine.StdPrint, weewx.engine.StdReport
Using database binding 'wx_binding', which is bound to database 'archive_sqlite'
System info
cpu cores: 2
bogomips: 4799.99
core id: 1
apicid: 1
fpu_exception: yes
stepping: 6
cache_alignment: 64
clflush size: 64
microcode: 0x36
cache size: 15360 KB
cpuid level: 10
fpu: yes
model name: Intel(R) Xeon(R) CPU E5-2620 v3 @ 2.40GHz
siblings: 2
physical id: 0
address sizes: 43 bits physical, 48 bits virtual
cpu family: 6
vendor_id: GenuineIntel
wp: yes
power management:
flags: fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts mmx fxsr sse sse2 ss ht syscall nx lm constant_tsc arch_perfmon pebs bts nopl tsc_reliable nonstop_tsc aperfmperf pni ssse3 cx16 sse4_1 tsc_deadline_timer hypervisor lahf_lm ida arat epb pln pts dtherm tsc_adjust
cpu MHz: 2399.998
model: 23
processor: 1
initial apicid: 1
Operating system: debian 8.7
Linux intranet 3.16.0-4-amd64 #1 SMP Debian 3.16.39-1 (2016-12-30) x86_64
1 minute load average: 0.00
5 minute load average: 0.02
15 minute load average: 0.06
General weewx info
Weewx version 3.6.2 detected.
Station info
Station type: Vantage
Driver: weewx.drivers.vantage
Driver info
[Vantage]
# This section is for the Davis Vantage series of weather stations.
# Connection type: serial or ethernet
# serial (the classic VantagePro)
# ethernet (the WeatherLinkIP)
type = ethernet
# If the connection type is serial, a port must be specified:
# Debian, Ubuntu, Redhat, Fedora, and SuSE:
# /dev/ttyUSB0 is a common USB port name
# /dev/ttyS0 is a common serial port name
# BSD:
# /dev/cuaU0 is a common serial port name
port = /dev/ttyUSB0
# If the connection type is ethernet, an IP Address/hostname is required:
host = 172.20.100.40
######################################################
# The rest of this section rarely needs any attention.
# You can safely leave it "as is."
######################################################
# Serial baud rate (usually 19200)
baudrate = 19200
# TCP port (when using the WeatherLinkIP)
tcp_port = 22222
# TCP send delay (when using the WeatherLinkIP):
tcp_send_delay = 0.5
# The id of your ISS station (usually 1). If you use a wind meter connected
# to a anemometer transmitter kit, use its id
iss_id = 1
# How long to wait for a response from the station before giving up (in
# seconds; must be greater than 2)
timeout = 4
# How long to wait before trying again (in seconds)
wait_before_retry = 1.2
# How many times to try before giving up:
max_tries = 4
# The driver to use:
driver = weewx.drivers.vantage
Currently installed extensions
No extensions installed
Archive info
Database name: weewx.sdb
Table name: archive
Unit system: 1 (US)
First good timestamp: 2009-02-26 14:30:00 CET (1235655000)
Last good timestamp: 2017-01-27 21:00:00 CET (1485547200)
Number of records: 138272
weewx (weewx.conf) is set to use an archive interval of 300 seconds.
The station hardware was not interrogated in determining archive interval.
Databases configured in weewx.conf
Database name: weewx.sdb
Database driver: weedb.sqlite
Database name: weewx
Database driver: weedb.mysql
Database host: localhost
Parsed and obfuscated weewx.conf
# WEEWX CONFIGURATION FILE
#
# Copyright (c) 2009-2015 Tom Keffer <tke...@gmail.com>
# See the file LICENSE.txt for your rights.
##############################################################################
# This section is for general configuration information.
# Set to 1 for extra debug info, otherwise comment it out or set to zero
debug = 1
# Root directory of the weewx data file hierarchy for this station
WEEWX_ROOT = /
# How long to wait before timing out a socket (FTP, HTTP) connection
socket_timeout = 20
# Do not modify this. It is used when installing and updating weewx.
version = 3.6.2
##############################################################################
# This section is for information about the station.
[Station]
# Description of the station location
location = Framnes KVGS
# Latitude and longitude in decimal degrees
latitude = 60.351
longitude = 6.182354
# Altitude of the station, with unit it is in. This is downloaded from
# from the station if the hardware supports it.
altitude = 28, meter
# Set to type of station hardware. There must be a corresponding stanza
# in this file with a 'driver' parameter indicating the driver to be used.
station_type = Vantage
# If you have a website, you may specify an URL
#station_url = http://www.example.com
# The start of the rain year (1=January; 10=October, etc.). This is
# downloaded from the station if the hardware supports it.
rain_year_start = 10
# Start of week (0=Monday, 6=Sunday)
week_start = 0
##############################################################################
[Vantage]
# This section is for the Davis Vantage series of weather stations.
# Connection type: serial or ethernet
# serial (the classic VantagePro)
# ethernet (the WeatherLinkIP)
type = ethernet
# If the connection type is serial, a port must be specified:
# Debian, Ubuntu, Redhat, Fedora, and SuSE:
# /dev/ttyUSB0 is a common USB port name
# /dev/ttyS0 is a common serial port name
# BSD:
# /dev/cuaU0 is a common serial port name
port = /dev/ttyUSB0
# If the connection type is ethernet, an IP Address/hostname is required:
host = 172.20.100.40
######################################################
# The rest of this section rarely needs any attention.
# You can safely leave it "as is."
######################################################
# Serial baud rate (usually 19200)
baudrate = 19200
# TCP port (when using the WeatherLinkIP)
tcp_port = 22222
# TCP send delay (when using the WeatherLinkIP):
tcp_send_delay = 0.5
# The id of your ISS station (usually 1). If you use a wind meter connected
# to a anemometer transmitter kit, use its id
iss_id = 1
# How long to wait for a response from the station before giving up (in
# seconds; must be greater than 2)
timeout = 4
# How long to wait before trying again (in seconds)
wait_before_retry = 1.2
# How many times to try before giving up:
max_tries = 4
# The driver to use:
driver = weewx.drivers.vantage
##############################################################################
# This section is for uploading data to Internet sites
[StdRESTful]
[[StationRegistry]]
# To register this weather station with weewx, set this to true
register_this_station = false
[[AWEKAS]]
# This section is for configuring posts to AWEKAS.
# If you wish to do this, set the option 'enable' to true,
# and specify a username and password.
enable = false
username = XXX obfuscated by wee_debug XXX
password = XXX obfuscated by wee_debug XXX
[[CWOP]]
# This section is for configuring posts to CWOP.
# If you wish to do this, set the option 'enable' to true,
# and specify the station ID (e.g., CW1234).
enable = false
station = XXX obfuscated by wee_debug XXX
# If this is an APRS (radio amateur) station, uncomment
# the following and replace with a passcode (e.g., 12345).
#passcode = replace_me (APRS stations only)
[[PWSweather]]
# This section is for configuring posts to PWSweather.com.
# If you wish to do this, set the option 'enable' to true,
# and specify a station and password.
enable = false
station = XXX obfuscated by wee_debug XXX
password = XXX obfuscated by wee_debug XXX
[[WOW]]
# This section is for configuring posts to WOW.
# If you wish to do this, set the option 'enable' to true,
# and specify a station and password.
enable = false
station = XXX obfuscated by wee_debug XXX
password = XXX obfuscated by wee_debug XXX
[[Wunderground]]
# This section is for configuring posts to the Weather Underground.
# If you wish to do this, set the option 'enable' to true,
# and specify a station (e.g., 'KORHOODR3') and password.
enable = false
station = XXX obfuscated by wee_debug XXX
password = XXX obfuscated by wee_debug XXX
# Set the following to True to have weewx use the WU "Rapidfire"
# protocol. Not all hardware can support it. See the User's Guide.
rapidfire = False
##############################################################################
# This section specifies what reports, using which skins, to generate.
[StdReport]
# Where the skins reside, relative to WEEWX_ROOT
SKIN_ROOT = /etc/weewx/skins
# Where the generated reports should go, relative to WEEWX_ROOT
HTML_ROOT = /var/www/html/weewx
# The database binding indicates which data should be used in reports.
data_binding = wx_binding
# Each of the following subsections defines a report that will be run.
[[StandardReport]]
# See the customizing guide to change the units, plot types and line
# colors, modify the fonts, display additional sensor data, and other
# customizations. Many of those changes can be made here by overriding
# parameters, or by modifying templates within the skin itself.
# The StandardReport uses the 'Standard' skin, which contains the
# images, templates and plots for the report.
skin = Standard
[[[Units]]]
[[[[Groups]]]]
group_altitude = meter
group_speed2 = meter_per_second2
group_pressure = mbar
group_rain = mm
group_rainrate = mm_per_hour
group_temperature = degree_C
group_degree_day = degree_C_day
group_speed = meter_per_second
[[FTP]]
# FTP'ing the results to a webserver is treated as just another report,
# albeit one with an unusual report generator!
skin = Ftp
# If you wish to use FTP, uncomment and fill out the next four lines.
#user = replace with the ftp username
#password = replace with the ftp password
#server = replace with the ftp server name, e.g, www.threefools.org
#path = replace with the ftp destination directory (e.g., /weather)
# Set to True for an FTP over TLS (FTPS) connection. Not all servers
# support this.
secure_ftp = False
# To upload files from something other than what HTML_ROOT is set
# to above, specify a different HTML_ROOT here.
#HTML_ROOT = /var/www/html/weewx
# Most FTP servers use port 21
port = 21
# Set to 1 to use passive mode, zero for active mode
passive = 1
[[RSYNC]]
# rsync'ing to a webserver is treated as just another report
skin = Rsync
# If you wish to use rsync, you must configure passwordless ssh using
# public/private key authentication from the user account that weewx
# runs as to the user account on the remote machine where the files
# will be copied.
#
# The following three lines determine where files will be sent.
#server = replace with the rsync server name, e.g, www.threefools.org
#path = replace with the rsync destination directory (e.g., /weather)
#user = replace with the rsync username
# Rsync can be configured to remove files from the remote server if
# they don't exist under HTML_ROOT locally. USE WITH CAUTION: if you
# make a mistake in the remote path, you could could unintentionally
# cause unrelated files to be deleted. Set to 1 to enable remote file
# deletion, zero to allow files to accumulate remotely.
delete = 0
##############################################################################
# This service acts as a filter, converting the unit system coming from
# the hardware to a unit system in the database.
[StdConvert]
# The target_unit affects only the unit system in the database. Once
# chosen it cannot be changed without converting the entire database.
# Modification of target_unit after starting weewx will result in
# corrupt data - the database will contain a mix of US and METRIC data.
#
# The value of target_unit does not affect the unit system for
# reporting - reports can display US, Metric, or any combination of units.
#
# In most cases, target_unit should be left as the default: US
#
# In particular, those migrating from a standard wview installation
# should use US since that is what the wview database contains.
# DO NOT MODIFY THIS VALUE UNLESS YOU KNOW WHAT YOU ARE DOING!
target_unit = US # Options are 'US', 'METRICWX', or 'METRIC'
##############################################################################
# This section can adjust data using calibration expressions.
[StdCalibrate]
[[Corrections]]
# For each type, an arbitrary calibration expression can be given.
# It should be in the units defined in the StdConvert section.
# Example:
foo = foo + 0.2
##############################################################################
# This section is for quality control checks. If units are not specified,
# values must be in the units defined in the StdConvert section.
[StdQC]
[[MinMax]]
barometer = 26, 32.5, inHg
outTemp = -40, 120, degree_F
inTemp = 10, 120, degree_F
outHumidity = 0, 100
inHumidity = 0, 100
windSpeed = 0, 120, mile_per_hour
pressure = 24, 34.5, inHg
##############################################################################
# This section controls the origin of derived values.
[StdWXCalculate]
[[Calculations]]
# Derived quantities are calculated by this service. Possible values are:
# hardware - use the value provided by hardware
# software - use the value calculated by weewx
# prefer_hardware - use value provide by hardware if available,
# otherwise use value calculated by weewx
pressure = prefer_hardware
barometer = prefer_hardware
altimeter = prefer_hardware
windchill = prefer_hardware
heatindex = prefer_hardware
dewpoint = prefer_hardware
inDewpoint = prefer_hardware
rainRate = prefer_hardware
##############################################################################
# For hardware that supports it, this section controls how often the
# onboard clock gets updated.
[StdTimeSynch]
# How often to check the weather station clock for drift (in seconds)
clock_check = 14400
# How much it can drift before we will correct it (in seconds)
max_drift = 5
##############################################################################
# This section is for configuring the archive service.
[StdArchive]
# If the station hardware supports data logging then the archive interval
# will be downloaded from the station. Otherwise, specify it (in seconds).
archive_interval = 300
# If possible, new archive records are downloaded from the station
# hardware. If the hardware does not support this, then new archive
# records will be generated in software.
# Set the following to "software" to force software record generation.
record_generation = hardware
# Whether to include LOOP data in hi/low statistics
loop_hilo = True
# The data binding used to save archive records
data_binding = wx_binding
##############################################################################
# This section binds a data store to a database.
[DataBindings]
[[wx_binding]]
# The database must match one of the sections in [Databases].
# This is likely to be the only option you would want to change.
database = archive_sqlite
# The name of the table within the database
table_name = archive
# The manager handles aggregation of data for historical summaries
manager = weewx.wxmanager.WXDaySummaryManager
# The schema defines the structure of the database.
# It is *only* used when the database is created.
schema = schemas.wview.schema
##############################################################################
# This section defines various databases.
[Databases]
# A SQLite database is simply a single file
[[archive_sqlite]]
database_type = SQLite
database_name = weewx.sdb
# MySQL
[[archive_mysql]]
database_type = MySQL
database_name = weewx
##############################################################################
# This section defines defaults for the different types of databases.
[DatabaseTypes]
# Defaults for SQLite databases
[[SQLite]]
driver = weedb.sqlite
# Directory in which the database files are located
SQLITE_ROOT = /var/lib/weewx
# Defaults for MySQL databases
[[MySQL]]
driver = weedb.mysql
# The host where the database is located
host = localhost
# The user name for logging in to the host
user = XXX obfuscated by wee_debug XXX
# The password for the user name
password = XXX obfuscated by wee_debug XXX
##############################################################################
# This section configures the internal weewx engine.
[Engine]
[[Services]]
# This section specifies the services that should be run. They are
# grouped by type, and the order of services within each group
# determines the order in which the services will be run.
prep_services = weewx.engine.StdTimeSynch
data_services = ,
process_services = weewx.engine.StdConvert, weewx.engine.StdCalibrate, weewx.engine.StdQC, weewx.wxservices.StdWXCalculate
archive_services = weewx.engine.StdArchive
restful_services = weewx.restx.StdStationRegistry, weewx.restx.StdWunderground, weewx.restx.StdPWSweather, weewx.restx.StdCWOP, weewx.restx.StdWOW, weewx.restx.StdAWEKAS
report_services = weewx.engine.StdPrint, weewx.engine.StdReport
Thomas Keffer
Jan 27, 2017, 5:33:15 PM1/27/17
to weewx-user
I take it you have a Weatherlink IP logger?
Have you disabled it from talking to the Davis Weatherlink site? Unfortunately, the way weewx is written, it is not possible to use weewx AND send data to the WL website. You must choose one or the other. To disable it, open a web browser, using the IP address of your WLIP. You should see a checkbox to disable it from talking to the WL website.
Mind you, I do not own a WLIP, so this is all second-hand knowledge!
-tk
--
You received this message because you are subscribed to the Google Groups "weewx-user" group.
To unsubscribe from this group and stop receiving emails from it, send an email to weewx-user+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
bus...@gmail.com
Jan 27, 2017, 6:32:06 PM1/27/17
to weewx-user
Thanks for the tip. The only device I have in addition to the Vantage Pro 2 is the Davis Ethernet adapter which connects the Davis box via ethernet to my server running WeeWX.
As you see from my config, the Davis interface IP is 172.20.100.40. I tried to connect via port 80 but no answer, when I tried via port 22222 the connection was reset. Do you have any more info on this scenario..?
regards Tor
As you see from my config, the Davis interface IP is 172.20.100.40. I tried to connect via port 80 but no answer, when I tried via port 22222 the connection was reset. Do you have any more info on this scenario..?
regards Tor
To unsubscribe from this group and stop receiving emails from it, send an email to weewx-user+...@googlegroups.com.
Thomas Keffer
Jan 27, 2017, 6:59:14 PM1/27/17
to weewx-user
When you say "I tried to connect via port 80" did you mean that you used a browser to go to http://172.20.100.40:80? Or something else?
-tk
To unsubscribe from this group and stop receiving emails from it, send an email to weewx-user+unsubscribe@googlegroups.com.
bus...@gmail.com
Jan 28, 2017, 3:11:33 AM1/28/17
to weewx-user
Yeah, I meant http://172.20.100.40 in a browser...
bus...@gmail.com
Jan 28, 2017, 3:59:51 AM1/28/17
to weewx-user
Hi again,
I don't think that anyone has registered our device to the online weatherlink database. But I will drive to the site later to collect the serial and device ID and check if they indeed are registered at weatherlink.com so we know.
However will the Weatherlink IP adapter by default in any case try to contact weatherlink.com and by that deny communications with weewx?
Is there a setting in the Vantage Pro 2 console setup where I can switch off this weatherlink communication?
best regards
Tor
I don't think that anyone has registered our device to the online weatherlink database. But I will drive to the site later to collect the serial and device ID and check if they indeed are registered at weatherlink.com so we know.
However will the Weatherlink IP adapter by default in any case try to contact weatherlink.com and by that deny communications with weewx?
Is there a setting in the Vantage Pro 2 console setup where I can switch off this weatherlink communication?
best regards
Tor
Thomas Keffer
Jan 28, 2017, 8:23:46 AM1/28/17
to weewx-user
Again, I don't own one of these, so I don't know the details, but I believe that by default it always tries to contact weatherlink.
I don't think there is a setting on the console where you can switch off this communication. I think you have to do it through a browser.
Any WLIP owners out there who can answer Tor's question?
-tk
To unsubscribe from this group and stop receiving emails from it, send an email to weewx-user+unsubscribe@googlegroups.com.
Reply all
Reply to author
Forward
0 new messages