the Wandboard Quad

182 views
Skip to first unread message

Junhwa Rhee

unread,
Jan 12, 2015, 10:36:17 PM1/12/15
to wand...@googlegroups.com
hello?

last year I received the Wandboard Quad I ordered from the future
electronics. (so far I have not ever used the board Unfortunately).

but even with the lot of Bootable Sdcard Images from the wandboard wiki
I cannot bring the board up and running with a suitable OS.

If the board is powered I see the two green "power" leds of the carrier
and cpu card And the red led inside the spdif.

the wandboard USB OTG show the following on the host system:

u-boot$ lsusb | grep Freescale
Bus 001 Device 059: ID 15a2:0054 Freescale Semiconductor, Inc. i.MX6Q
SystemOnChip in RecoveryMode

according to i.MX6DQ RM, "The boot code performs hardware
initialization, loads the Program Image from the chosen boot device,
performs image validation using the HAB library, and then jumps to an
address derived from the Program Image. If any error occurs during
internal boot, the boot code jumps to the Serial Downloader."

anyway, in my wandboard quad the boot code can NOT load u-boot image
from SD card(0x400) and No serial console output seen so far. so just
the boot code jumps to the Serial Downloader.

Whatever I try, changing SD card, power supply, serial cables, etc.

I do not see any response on the serial console using the stock images
from the wandboard download page.

now what should I do?

Regard,
JR

Junhwa Rhee

unread,
Jan 13, 2015, 1:55:37 AM1/13/15
to wand...@googlegroups.com
I am using Wandboard Quad C1.

Sander Idelson

unread,
Jan 13, 2015, 2:23:35 AM1/13/15
to wand...@googlegroups.com
It looks like you have bricked your wandboard. Try following these instructions to reflash the serial EEPROM:
http://boundarydevices.com/unbricking-nitrogen6x-sabre-lite-i-mx6-board/

Hope that helps,

Sander
Message has been deleted

Junhwa Rhee

unread,
Jan 13, 2015, 4:10:22 AM1/13/15
to wand...@googlegroups.com
Hi Sander, Thank you for your quick reply.

I tried to check it but not a good result.

imx_usb_loader$ sudo ./imx_usb u-boot.imx
config file <./imx_usb.conf>
vid=0x066f pid=0x3780 file_name=mx23_usb_work.conf
vid=0x15a2 pid=0x004f file_name=mx28_usb_work.conf
vid=0x15a2 pid=0x0052 file_name=mx50_usb_work.conf
vid=0x15a2 pid=0x0054 file_name=mx6_usb_work.conf
vid=0x15a2 pid=0x0061 file_name=mx6_usb_work.conf
vid=0x15a2 pid=0x0063 file_name=mx6_usb_work.conf
vid=0x15a2 pid=0x0041 file_name=mx51_usb_work.conf
vid=0x15a2 pid=0x004e file_name=mx53_usb_work.conf
vid=0x15a2 pid=0x006a file_name=vybrid_usb_work.conf
vid=0x066f pid=0x37ff file_name=linux_gadget.conf
config file <./mx6_usb_work.conf>
parse ./mx6_usb_work.conf
15a2:0054(mx6_qsb) bConfigurationValue =1
Interface 0 claimed
HAB security state: development mode (0x56787856)
== work item
filename u-boot.imx
load_size 0 bytes
load_addr 0x00000000
dcd 1
clear_dcd 0
plug 1
jump_mode 2
jump_addr 0x00000000
== end work item
main dcd length 310
sub dcd length 30c
w3 in err=-1, last_trans=0 00 00 00 00
addr=0x021b0404, val=0x00011006
w4 in err=-1, last_trans=0 00 00 00 00
!!perform_dcd returned -1
HAB security state: development mode (0x00000000)

Sander Idelson

unread,
Jan 13, 2015, 9:29:07 AM1/13/15
to wand...@googlegroups.com
Junhwa,

Please read the comments on the page I sent you. There are newer branches of u-boot that you should try, specifically for wandboard quad. Make sure that you load the correct u-boot and pull out the SD card while uploading the new boot loader.

Reply all
Reply to author
Forward
0 new messages