Gcc Sable 60 Driver Windows 7 Download
Magali Swinderman
At first I suspected a switch, but then after wiggling the "Flasher" relay of all things it would work. Decided to remove the GEM module which is attached to the under dash fuse panel to investigate for a poor solder joint. Once I got the GEM module removed and taken apart its clear to see the design does not allow for repair. There is two circuit boards that are held together by almost 50 soldered pins making it totally a waste of time to even try.
Apparently this problem with the GEM module is well known, as occurs as a result of the "auto" down feature running thru the GEM module. I decided to bypass this feature and all seems to be working well now.
To bypass the "Auto" down feature that runs thru the GEM module you remove the door panel and cut the orange and white wire to the window motor. Then cut the light blue and tan wire from the blue plug that connects to the window switch. Using a splice wire connect the light blue and tan wire (from the plug) to the orange and white wire (to the window motor plug). Now tape off the disconnected wires to ensure they do not short and all should be well and the GEM module removed from the operation on the drivers side front. The job is made easier by removing the speaker to gain access to the window motor plug (this way you do not have to remove the windowmotor).
I should also mention I have seen switches themselves go bad in the past, however in the case the window goes down but not up its probably a problem with the GEM Module if the problem is limited to the front drivers side. If you do need a switch the aftermarket now sells them for $35 manufactured by Dorman.
Thank you very much for your informative post. I have a 2001 Sable (dohc) and my drivers door window has not worked since I purchased the car (1 yr) but all other windows worked great. I finally decided to repair the window. I bought a new motor/regulator (did not fix the prob), so I bought a new master window switch (again did not fix problem, took car to ford dealer they said GEM Module ... Obsolete but they found one only$1,300.00 ....I found a used one for $35 but dealer claimed they could not program it for some unknown reason. Then I just spotted your post and couldn't be happier. My drivers window doesn't go up or down so I was hoping you inform me of how to bypass up and down functions ? I thank you very much for your time and hope for your reply
The instructions of how I bypassed the "auto" feature of the GEM module for the driver window are listed in this post. I don't know what else I can offer you as I did not take photos of this repair. Doing a search on google for this repair may help you, as I'm sure someone out there has taken photos of this repair.
Unfortunately you will not be able to get running on USB to USB cables. The USB port on your cutter is not for job information. If you only have USB available on your computer you can purchase a Keyspan High-speed USB Serial Adapter. (
generelly drivers are packaged as dll's, inf files, this is a pre packaged exe that does not unpack, it requires you do do this button pressing garbage on the cutter to get it into this USB common mode "whatever that is"
I understand its a strech sometime to get old hardware working in windows7 let alone x64.. but the company has drivers for them... I have recommended my buddy to call GCC and get some tech support assistance with it... I know horrible, but thats what has to happen sometime
There are some great deals on EBAY for XP computers. , I never upgrade, I have an XP computer and I keep an XP backup..And I run a business. My computer is dedicated just for my cutter. . more reliable and stable. As yours should be, dedicated just for your vinyl cutter only. You can pick up xps for $50.00... LOOK... alot with serial cables.Why does it have to be windows 7? You don't need a new powerful computer to run a vinyl cutter..
I have spent a bit of money filling my PC out with corsair fans and AIO so I am a little bit upset to find that my system performance issues are directly related with icue being installed. I dont know why this is happening but having icue installed results in stuttering and frame drops that are really notable in VR. It is harder to notice in flatscreen games but in VR it is devastating.
Uninstalling icue immediately resolves the issues. I want my fan curves and the ability to turn off all my RGB or set it to just white light. Not running icue defaults in red lights that I dont want running. I have installed and uninstalled and noted the performance issues multiple times so I know it is a direct correlation with the icue software being installed.
I tried setting it so the icue software does not run when windows starts and the performance issues persist. The software must be COMPLETELY uninstalled. There must still be some system process that runs even though it is set not to run when windows starts that is causing the performance issue. I have ALSO tried just closing out of the icue app after it runs and the performance issues will persist. The only way to stop the issue is to uninstall the software. No additional registry cleaning or closing of any other app is required.
I have also tried reinstalling windows and all my apps and icue does this even when it is basically the only piece of software running on my PC besides built in windows defender and nvidia drivers. I do not use geforce experience or anything else that I can think of that might interact with icue.
The Corsair.Service 32 bit and CPUID service still start with Windows, although they shouldn't be doing much with no app to hand over data. However, it does suggest the Corsair.Service is becoming entangled with something else. Common conflicts are with other full spectrum monitoring programs like AIDA or HWinfo, but now that all the MB and other RGB control software do the full system monitoring and not just RGB control, it is possible for those to become problems as well.
We did not solve Nobleflame's issue either. Between the 3 of us, we have pretty similar hardware with mine being Asus Z790 Hero, 13900K, and Gigabyte 4090 OC GPU. I am not seeing any kind of performance drop and I monitor this stuff methodically. This makes me think we are looking for another program or program type you both might be using that is getting twister around CUE's services. Look in your task manager for CPU% and see if System Interrupts is near the top of the list. It should not be and that usually suggests USB traffic problems. The other thing you both might do is look in your Event Viewer (right click on Windows button) -> Windows Logs -> System and look for red/yellow errors. There will be a bunch of garbage stuff like DCOM errors that don't matter, but any red flag likely does or more likely you're looking for long streams of repeated WHEA or other errors in there.
ICue is really using more CPU than it should in my AM5 setup.
It is a fact that recent versions of ICue are causing a big mess on many systems.
The sooner Corsair admits and fixes its software, the better for everyone.
What is odd is it seems like the system tries to limit itself.... my average minimum refresh rate on my index headset drops to 139 and I have 3-4% reprojection. When I move around in a game that is normally butter smooth, things feel a bit disjointed and stuttery. It is playable, but you can feel the reprojection. Without icue installed there is .2% reprojection and it sits at 143/144hz and is super smooth with no stuttering, even in very intense action. The GPU seems to scale well with increased load without icue installed.
When icue IS installed, if I drop my VR headset from 144hz to 90hz, the frame drop/reprojection will scale and maintain the same %. Dropping to 90hz with 3-4 reprojection would normally eliminate the reprojection if all other values remain the same so this is odd behavior for it to maintain the poor performance. System interrupts seem to bounce up and down from the top 8 items. I have a dcom error but no "WHEA" or anything like that. This is so frustrating. I hope I can find a solution or I will be ripping out these fans for ewaste and going with some cheap fans off amazon and a non corsair AIO.
b37509886e