Roofing felt v temperature

[ss]

It looks like I may have a weather window to allow me to refelt the shed
roof, next 3 days forecast as dry. My intention is get the old stuff off
over 2 days and then replace.
One issue maybe the temperature as the max is about 6C and I have bought
the better quality stuff. Laying it flat should not be a problem but
would it be adviseable to use a `paint stripper` heat gun to heat the
edges before bending the felt to fit over the edges or should this not
be necessary.

[Bill Wright]

Put the felt in the shed and wait until May.

Bill

[Bob Minchin]

+1

[Dennis@home]

You need a 30kw propane gun to do felt properly in this weather. In fact
you need it in summer if you use decent hot lay felt.

If its leaking tie a tarp over it until June.

[Tim Watts]

Yes.

My roofers did a flat bit of dormer in December. It was cold.

They used a flame gun (mega blowtorch) to soften the felt, then pre
formed it (edging strips) over a wooden former on the ground.

More heat was used when the installed it and the rest of the felt.

But yes, everything was warmed up before forming.

[ss]

OK consencus is leave until May/June I have ordered a cheap tarp of ebay
to keep dry intil then.

[Dave Liquorice]

On Thu, 05 Feb 2015 12:58:48 +0000, ss wrote:

> One issue maybe the temperature as the max is about 6C and I have bought

> the better quality stuff. Laying it flat should not be a problem ...

Is this torch on felt or just ordianry shed roofing felt? I wouldn't
like to bet on getting ordinary stuff to lay flat without a fight at
current temperatures. if you can bring it indoors let it warm up for
24 hours and cut to length plus abit inside you might be able to get
it in place before it cools...

> ... would it be adviseable to use a `paint stripper` heat gun to heat
> the edges before bending the felt to fit over the edges ...

Yes. But I wouldn't attempt it until it's a lot warmer. If it's
leaking temporary bits of "up and under" cut up feed bag and few
clouts might be enough.

--
Cheers
Dave.

[Nightjar .me.uk>]

Make sure it is well tied down. The wind has been doing its best to
loosen the ropes on the one over my shed. As I will be replacing the
felt that the wind tore off with steel profile roofing, I don't need to
wait until May, just until I get the tuit.

https://www.cabp.co.uk/Roofing-Sheets/Corrugated-Sheets/Steel-CA32-1000-Profile.htm

--
Colin Bignell

[Bill Wright]

Dave Liquorice wrote:

> Is this torch on felt or just ordianry shed roofing felt? I wouldn't
> like to bet on getting ordinary stuff to lay flat without a fight at
> current temperatures. if you can bring it indoors let it warm up for
> 24 hours and cut to length plus abit inside you might be able to get
> it in place before it cools...

He could always build a bonfire inside the shed.

Bill

[ss]

Ordinary roof felt.

>
I have ordered a cheap tarp to cover the complete roof, its big enough
so I can fix on to the sides of the shed to prevent the wind getting
underneath it. Also got plenty of broken slab to weigh it all down at
the edges. Its a mono pitched roof approx 9` x 6`.

[fred]

In article <3wQAw.500849$re.3...@fx40.am4>, ss <wee...@hotmail.com>
writes

>>
>I have ordered a cheap tarp to cover the complete roof, its big enough
>so I can fix on to the sides of the shed to prevent the wind getting
>underneath it. Also got plenty of broken slab to weigh it all down at
>the edges. Its a mono pitched roof approx 9` x 6`.
>

Toolstation and all the usual suspects have plastic tarps the size of a
football pitch for buttons. You can fix them down with battens screwed
down the slope and as you are re-felting, the screw holes make no odds.
Add some silicone under the batten at the screw points if you want it
properly waterproof. I've staved off a re-felt on a huge shed for 6 mths
by doing this in the past.

--
fred
it's a ba-na-na . . . .

[ss]

Thanks Fred