Google Groups no longer supports new Usenet posts or subscriptions. Historical content remains viewable.
Dismiss

Removing drawers from Filing cabinet

562 views
Skip to first unread message

Donwill

unread,
Feb 1, 2010, 11:26:52 AM2/1/10
to
I have an Ostaline 2 drawer grey metal filing cabinet, I need to remove
the drawers to make some mods to the case. Does anyone know if there is
a little catch or toggle that releases the slide to remove drawers. I
don't want to damage the mechanism by being a bit rough with it.
Don
Message has been deleted

John

unread,
Feb 1, 2010, 11:35:31 AM2/1/10
to

"Tim Watts" <t...@dionic.net> wrote in message
news:hk6vii$1og$2...@news.eternal-september.org...
> Donwill <Donwill...@invalid.invalid>
> wibbled on Monday 01 February 2010 16:26
> Usually some little wibbly catch on the rails. Sometimes next to the
> drawer
> end, sometimes halfway down where the two halves of the rail join. One on
> each side.
>
> --
> Tim Watts
>
> Managers, politicians and environmentalists: Nature's carbon buffer.
>
Some drawers lift off the rail / runner.


Usenet Nutter

unread,
Feb 1, 2010, 12:20:48 PM2/1/10
to

Assuming filing cabinets are made the way theye were when I worked in
an office then pull the drawer right out ( but watch it doesn't tip
over if it is top heavy) then check if there is a catch on the runners
..one at each side and if there is then poperate the catch and the
drawer should pull out the runners ....or if not see if there is a gap
in the moving runner that coincides with a lip on the drawer runner
and tip the drawer up at that point and it should lift out .

John L

unread,
Feb 1, 2010, 12:33:30 PM2/1/10
to
Pull drawer out as far as it goes; pull front upwards (so the drawer is
angled upwards), and pull some more.

John

The Medway Handyman

unread,
Feb 1, 2010, 1:20:19 PM2/1/10
to

Angle grinder.


--
Dave - The Medway Handyman
www.medwayhandyman.co.uk


Donwill

unread,
Feb 1, 2010, 2:35:58 PM2/1/10
to
The Medway Handyman wrote:
> Donwill wrote:
>
>> I have an Ostaline 2 drawer grey metal filing cabinet, I need to
>> remove the drawers to make some mods to the case. Does anyone know if
>> there is a little catch or toggle that releases the slide to remove
>> drawers. I don't want to damage the mechanism by being a bit rough
>> with it.
>>
>
> Angle grinder.
>
>
>
It may come to that since I cannot find anything that remotely looks
like a toggle or a catch gismo.
Don

John L

unread,
Feb 1, 2010, 4:20:00 PM2/1/10
to
> > Angle grinder.
> >
> It may come to that since I cannot find anything that remotely looks
> like a toggle or a catch gismo.

In that case do what I suggested: pull up the front of the drawer when
it gets to its limit, then pull outwards again: there's probably two
sets of overlapping castors in rails, in there.

Cheers
John

Peter Twydell

unread,
Feb 1, 2010, 5:24:24 PM2/1/10
to
In message <7sodmb...@mid.individual.net>, Donwill
<Donwill...@invalid.invalid> writes

Just to be different, the drawers on one of mine are screwed to the
runners at the sides. Probably only applies to wooden cabinets though.

The metal cabinets have catches at the front of the runners.
--
Peter

Ying tong iddle-i po!

Chris J Dixon

unread,
Feb 2, 2010, 2:01:45 AM2/2/10
to
Donwill wrote:

>The Medway Handyman wrote:

>> Angle grinder.
>>
>It may come to that since I cannot find anything that remotely looks
>like a toggle or a catch gismo.

Perhaps if you were to put some detail photos on line somewhere
we might be able to make suggestions. Whilst not impossible, I
don't think the easiest construction methods would make the
drawers permanent.

One of mine has little plastic devices for release, but the
cheaper one simply has metal tabs on the slides locating in slots
in the drawer.

Chris
--
Chris J Dixon Nottingham UK
ch...@cdixon.me.uk

Have dancing shoes, will ceilidh.

Donwill

unread,
Feb 3, 2010, 5:31:54 AM2/3/10
to
Thanks for all the helpful suggestions , I got them out in the end.
For anyone wanting to do the same with a similar cabinet :-
For each drawer, there were two small push-fit black plastic covers that
hid metal tags protruding upwards from the front of the metal runners.
These tags were located into slots in the upside down U channels that
are positioned at the sides of the base of the drawer.
The tags were slightly twisted to hold the drawer on to the slides and
slight untwisting with a pliers and a gentle tap on the tags released
the drawers.

Many thanks
Don

John L

unread,
Feb 3, 2010, 8:04:21 AM2/3/10
to
In article <7st1ko...@mid.individual.net>,
Donwill <Donwill...@invalid.invalid> wrote:

> Thanks for all the helpful suggestions , I got them out in the end.
> For anyone wanting to do the same with a similar cabinet :-
> For each drawer, there were two small push-fit black plastic covers that
> hid metal tags protruding upwards from the front of the metal runners.
> These tags were located into slots in the upside down U channels that
> are positioned at the sides of the base of the drawer.
> The tags were slightly twisted to hold the drawer on to the slides and
> slight untwisting with a pliers and a gentle tap on the tags released
> the drawers.

Blimey. Looks like we were all wrong then, afaicr. The lengths people
will go to, to protect us from ourselves! :-)

J.

Chris J Dixon

unread,
Feb 3, 2010, 9:40:46 AM2/3/10
to
John L wrote:

I thought I was close with my second option:

>One of mine has little plastic devices for release, but the
>cheaper one simply has metal tabs on the slides locating in slots
>in the drawer.

Glad it got sorted without weapons of mass destruction.

0 new messages