Tp Link Modem Driver For Windows 7

0 views

Skip to first unread message

Denisha Cerniglia

unread,

Aug 3, 2024, 10:32:58 AM8/3/24

to todilama

Please I would like to know how I can make my EM7565 module card to work on my dell Latitude 7280 windows 11 64bit.It was working when I had windows 10 64bit installed. I had to upgrade to windows 11.

Also on windows 11 the modem is working fine and perfect. After RESTART, I do not have to ON airplane mode and OFF again before the modem starts working. Its start working right after RESTART when Wifi is OFF.

Cheap and seems adequate but not rated for win 10. Are there drivers built in to Windows that would allow this to function? Would I need to hunt for software as one reviewer did? Windows Fax and Scan should be good enough for my occasional use.

Thanks Paul
I see I may have another obstacle , VOIP can scramble the Fax signal. I have Fios which seems to be Voip. At worst if windows 10 did not work I could have tried a W7 VM but the scrambling would be a deal breaker. I will investigate and return.
David

During small investigation i find that if i change setting (for example Energy Efficient Ethernet) in Advanced tab of adapter (in Device Manager) - i have exactly the same message in Event Viewer right after change apply. For me it look's like right after system boot something (maybe specific setting) apply on adapter, it do it thing (turn off\turn on - i don't know) and warning appear in Event Viewer.

For this matter, as you stated that you have installed the driver from a bigger pack which means you may install it from the generic Intel drivers. Please kindly refer below for the steps that you can take to mitigate the issue:

Also. does the card connects to a switch? If yes, if the Energy Efficient Ethernet is set to OFF with the switch port enabled, it may caused the connection to be dropped for a while and prompting the event 27 to occurred

Lastly I would recommend a clean driver installation however since you are using an ASUS card which is an OEM from Intel, it's best to check with the manufacturer as the software drivers linked from Intel page are generic versions, and can be used for general purposes. The cards are also configured and tailored to run with the OEM's requirement of the card. To avoid any potential installation incompatibilities on the OEM system, Intel recommends checking with the OEM and use the software provided via the system manufacturer.

Understood that you are having an issue with the i211 NIC getting disconnected. For this matter, can you help to elaborate by the meaning It happening right after each boot, does it meant that the NIC will disconnect every time you boot the PC and continues to disconnects? Or was it an intermittent issue where the NIC will sometimes disconnects and reconnect on its own?

Let's be crystally clear about this: I have got "Warning message with number 27 in Even Viewer right after each boot of OS". But as soon as i run Google Chrome - connection to internet is working. I am 100% sure it is (connection) exist after warning message, but i not sure it exist before warning message since time window is too small to react or check (few seconds, meybe less). So, connection after warning message exist all the time - i may view YouTube videos\long Twitch streams - no problems detected and no new warnings.

Message in Event Viewer will be exactly the same. Like it's disconnected, but it working fine after. Apply of setting require disconnect (reconnect) of adaper. But for some reason it's happening after each boot and i don't know how (or where) to look what's going on with adaper from press of "Start" button on motherboard till getting warning message.

I may try to install Windows 10 Pro (clean install) on another disk and check if there will be error. That way it will be possible to exclude adapter from equation (if there will no error on boot - problem in Windows 11 Pro or it's services configuration).

2. Another way to confirm (or prooth as you wish) is to take a look in Release Notes (PDF file) on page. If we open page #10 of PDF "Table 4. Supported Operating Systems: Windows Client pcontinued]" it's have got driver name "e1r" and in collumn "Microsoft Windows 11" we can see version of driver - 13.0.14.x;

I think it's more productive to try find solution for a problem then waste time on false discussion that product don't supported (because if it's not supported - cut if from driver). I belive that in Intel work great engineers, they make all this things after all, and if right people take a look on a problem they find solutiuon even faster then 3 days.

From my side, i am ready to find solution, offer my time on research and test options. Why i need that? Because i know that many other people with such motherboars or such cards on diffirent boards have same problem too and need solution for it.

Intel does not verify all solutions, including but not limited to any file transfers that may appear in this community. Accordingly, Intel disclaims all express and implied warranties, including without limitation, the implied warranties of merchantability, fitness for a particular purpose, and non-infringement, as well as any warranty arising from course of performance, course of dealing, or usage in trade.

I have the exact same issue. It won't show up on the list of available networks of my laptop. It has windows 10 too. It shows and works fine in other devices (laptops, cellphones, tablets). I don't know what to do about it

The Nokia Tower offers a wide selection of Wifi Channels which is fantastic. These channels are used world wide meaning not all channels are used in all countries. Its a global device. The Channels offered to us in the USA includes some channels with restrictions and not commonly used in typical routers. In this respect the Nokia router is superior, as you can truly set a channel in a crowded wifi area that no one else uses.

More or less, it is something with your computer and not the Nokia Tower. Try refreshing your network on the computer because no matter what, its should be seeing the 2.5 network at the least, no matter what settings on the router.

How do I change set it to "auto"? I have the nokia gray tower. I changed the name it with and it works on all other devices but on my laptop's list of network does not show. I don't know what you mean by select your own channel.

PROBLEM SOLVED. I was having the same issue with an older Asus laptop. When I had the 4G LTE router/modem from T-Mobile the network would show up on my laptop but once I got the 5G one the network wouldn't show up on my laptop but it would show up on all other devices. The work around I found was purchasing the TP-Link RE300 range extender. You connect the range extender to the 5G router/modem then connect the problem device to the range extender. In my case it was my laptop which is now connected to the range extender and working fine. This range extender is 2.4ghz and 5g compatible. Not sure if other range extenders would work as this is the only one I own and have tried. Also, I just ran a speed test and there's no noticeable difference in speed due to being connected to the range extender instead of the T-Mobile router/modem directly.

After installing the T-Mobile Gateway Gray Kit I was unable to see the SSID name in the list of available networks on my 2017 HP Laptop running Windows 10, but everything else in the house connected, since I renamed Gateway to the previous router SSID name. I searched the type of wireless adapter I have in laptop, Intel Dual Band Wireless-AC 7265, and visited Intel site to update Wireless adapter Driver to the latest for my device, 19.51.33.1. After the update I am able to see the Gateway SSID and laptop connects.

Hello all. I am new to the TMobile Gateway. I just got the grey Gateway tower and I am having the same issues with my older laptop not connecting or even seeing my SSID. Everyone else in my house can connect and be on it just fine but when I got to connect my laptop it won't come up. It's a Toshiba Satellite Pro L850 series running Windows 8. I have done everything I can think of to find my connection. I went in and made sure my Wifi adapter was up to date, rolled back the drivers and even went in to command prompt and did the config. Still nothing. What am I doing wrong or what do I need to do to get it to connect??