How To Reset Epson L565 Printer To Factory Settings
Gaetan Boren
Making Changes to Copy SettingsChanging the number of copies
Selecting the paper
Adjusting the density
Adjusting the contrast
Adjusting the RGB color
Specifying the zoom ratio
Making 2 pages per sheet copies
Reset the copy settings
When you plan to copy your document using other than the default settings, you can make changes to the appropriate copy settings as follows. Use the Up or Down button to move between menu items.
Make sure that the product is in Copy mode. If not, press the Copy button to enter the Copy mode. Make sure the value next to Copies is highlighted in the LCD panel, and then enter the number of copies to be made using the numeric keypad. Note:You can also use the Right or Left button to increase or decrease the number, one digit at a time.
[Top]
Note:When you place multiple documents in the Auto Document Feeder and make a continuous high quality (600 dpi) color copy with the default memory (128 MB), the product may not work properly because of insufficient memory. We recommend adding an memory module so that the total memory size is 256 MB or higher. Make sure that the product is in Copy mode. If not, press the Copy button to enter the Copy mode. Press the Up or Down button several times until Color DocType or B&W DocType appears. Press the Left or Right button several times until your desired document type appears.
[Top]
Adjusting the densityYou can adjust the image quality in density by selecting from 7 levels (-3 to 3). The higher the level, the darker the image. The default level is 0. For adjusting the image quality, see also Adjusting the contrast and Adjusting the RGB color.
Make sure that the product is in Copy mode. If not, press the Copy button to enter the Copy mode. Press the Up or Down button several times until Density appears.The current value next to Density is highlighted. Specify the density.Note:To increase or decrease the density, press the Right or Left button, respectively. The density increases or decreases one level at a time.
[Top]
Adjusting the contrastYou can adjust the image quality in contrast by selecting from 7 levels (-3 to 3). The higher the level, the greater the contrast becomes. When you adjust the contrast to a lower level, the difference in brightness decreases. The default level is 0. For adjusting the image quality, see also Adjusting the density and Adjusting the RGB color.
Make sure that the product is in Copy mode. If not, press the Copy button to enter the Copy mode. Press the Up or Down button several times until Contrast is selected.The current value next to Contrast is highlighted. Specify the contrast level.Note:To increase or decrease the contrast, press the Right or Left button, respectively. The contrast increases or decreases one level at a time.
[Top]
Make sure that the product is in Copy mode. If not, press the Copy button to enter the Copy mode. Place your original either on the document table or in the Auto Document Feeder (fax model only). For details, see Setting Your Originals. Press the Down button to select Zoom. Specify your desired zoom ratio with either of the following methods.Selecting a zoom ratio:
Press the Left or Right button several times until the desired fixed zoom ratio is displayed.
The following document fixed zoom ratios are available:Zoom Ratio Settings
Setting a zoom ratio:
You can also specify a magnification rate between 25% and 400% using the numeric keypad.Note:If the Left or Right button is pressed after entering a magnification rate using the numeric keypad, the closest fixed value to the entered rate is displayed.Full-page copyThe full-page copy function is used to slightly reduce the output in order to fit the document into the guaranteed print area of the product. Normally, the guaranteed printable area of a photocopier is limited. Therefore, when a photocopier copies a document with text or image printed on the whole sheet of paper, part of the text or image on the edges of paper will not be copied. This function is enabled when On is selected.
Make sure that the product is in Copy mode. If not, press the Copy button to enter the Copy mode. Place your original either on the document table or in the Auto Document Feeder (fax model only). For details, see Setting Your Originals. Press the Down button twice to select Full Copy. Press the Left or Right button to select between On and Off.
[Top]
Using the Auto Document FeederWhen you set all documents in the Auto Document Feeder and press the B&W Start or Color Start button, the documents are fed automatically, and then scanning starts. If you set an odd number of sheets in the Auto Document Feeder, a half of the last page is output blank.
Reset the copy settingsThe currently selected setting can be reset to the default value by pressing the Reset button. Pressing the Reset button for a while resets all setting values to the default and the LCD panel returns to the initial display.
Press the Setup button on the control panel.
The Setup light is on and the Setup menu appears in the LCD panel. Press the Down button until Copy Settings appears, and then press the Right button. Press the Down button to select Factory Settings, and then press the Right button. Make sure that Factory Settings is selected, and then press the Right button. When all settings are changed to the factory settings, the product returns to the Print mode.
[Top]
While troubleshooting your Epson printer, you may need to completely reset the device. A factory reset will return your printer to its out of the box settings. This guide will help you factory reset your printer.
4a15465005