Draytek 2762 Default Password
Kevin
To get access to your DrayTek Vigor2762, you need the IP of your device, the username and password. You'll find such information in the Manual of your DrayTek Vigor2762 router. But if you do not have the manual for your router or you do not want to read the whole manual to find the default login information then you can use the quick guide below. To get to the router login page it's necessary that you are connected to the router.
Try different ID/password combinations that are widely used by DrayTek that you'll find below. In this list are the most popular default username and password combinations used by DrayTek. Sometimes the username and password doesn't work that we mentioned in the top of this guide. Then you can try these username/password combinations below to get access to your DrayTek Vigor2762 wireless router.
Manual
Nothing of the methods worked for me and I still not get access to my DrayTek ! All you need to do is to reset your modem. This can be done easily by clicking on the reset button at the back or at the bottom of your router. If you hold down this small button for approximately 20 seconds, (you may have to use a toothpick), then your modem will get restored to the factory settings. What you need to keep in mind is that when you reset your modem, you will lose your connection online. It is therefore better to take an expert's assistance in this regard. Note: If you have not enough information, it is obviously recommended that you should get help from a person who has all the knowledge about this topic.
2. Make sure the network interface is using an IP in the 192.168.1.0/24 subnet, you can skip this if it is using DHCP, or "obtaining an IP address automatically," which is the default settings for most devices. (You can change the network configuration from Control Panel > Network and Internet > Network Connections, double-click on the connection to Vigor router, then go to TCP/IPv4 Properties. )
3. Open a browser on the computer. In the address bar, enter 192.168.1.1 (which is router's default LAN IP address). Hit Enter, and you will access the router's login page. The default login username and password are both admin. (If you can't open the login page, see Why can't I access my Vigor Router? to troubleshoot)
To get access to every router of DrayTek (e.g. Vigor 2800VG ,Vigor 2925ac or Vigor 120 ), you need the IP of your router, the username and router password. You can find these information in DrayTek router manuals. But if you do not have the manual for your router or you do not want to read the whole manual to find the default login information then you can use the quick guide below.
- Open your internet browser (e.g. Chrome, Firefox, Opera or Internet Explorer)
- Type 192.168.1.1 (the most common IP for DrayTek routers) in the address bar of your web browser to access the router's web-based user interface.
- You should see 2 text fields where you can enter a username and a password.
- The default username for your DrayTek router is admin.
The default password is admin. - Enter the username & password, hit "Enter" and now you should see the control panel of your router.
In the list below you will see the most popular default username and password combinations used by DrayTek. Sometimes the username and password doesn't work that we mentioned in the top of this guide. Then you can try these username/password combinations below to get access to your wireless router.
Sometimes you need your router web interface IP address to change security settings. Most people don't know their router IP address. Most times you'll find this IP on the bottom or back of your router device. But if you are not able to find this IP on your router or in the user manual then you can try some methods to get the router I.In the list below we listed all known router IPs for the manufacturer DrayTek.
We are being moved to digital voice soon. We dont' have/use bt smart hub 2 - instead a draytek vigor 2862 router. Can I connect my landline to draytek in the same way I would if we had hub2?? If not, how can we get round this?
As far as he Draytek router is concerned I have changed very few settings via the Web admin page for this router, apart from making some bespoke settings for BT IP settings when I first took delivery. It has worked faultlessly out of the box since 2014.
I have tried contacting Draytek support for some help but they speak in very convolute, obtuse and perplexing manner. I am not a complete dork and can manage most PC techie challenges but this one is unfamiliar territory for me having not ventured into the depths of Draytek Web Admin page historically.
This based on a 2762. The 2862 is the industrial version and a bit over the top for home use. Draytek do a simulation interface on their website, however, that suggests the user interface on the 2862 is practically identical, so:
(*In the original post I left out IPv6. If you want IPv6 the easiest way is, on the Draytek go to LAN > General setup > LAN1 IPv6 button. Tick the enable box and set it for WAN2. Disable the DNS and DHCP settings. On the Smart Hub you will need to go into Advanced > IPv6 > Configuration and set it to Stateless. ULA can be left off).
Thanks, you are very kind and considerate person to respond rapidly, efficiently and in manner that can be followed by a beginner like me. See my response to some of your questions in Italic text below along with a further question from me.
This based on a 2762. The 2862 is the industrial version and a bit over the top for home use. Draytek do a simulation interface on their website, however, that suggests the user interface on the 2862 is practically identical, so: Sorry for clarification I have a Draytek Vigor 2860Vn- Plus, I could not afford of justify the 2862
Just to clarify again,...I've reversed the use of 1 and 0 in the third postion here, relative to my original post. This should be less work in your case. Yep I can see & understand what you have done here to stop it clashing with the BT SH2.
Hi,
I'm on the Unlimited Fibre Extra and changed the supplied router for the Draytek 2860 as I wanted more granular control over QoS, which has been working fine for what we need.
Now when there are no issues, I can connect up the 2860 and the broadband all comes online in a couple of minutes, so I know Plusnet specific settings are correct, but we live in an area where I know the local exchange have some issues and every now and again, especially in wet weather, the line drops.
The issue I've been having is the 2860 doesn't bring the broadband up again after this happens. What I've had to resort to is plugging the supplied Plusnet router in, which bring the line back up in a couple of minutes, then I can unplug and connect the 2860 back, and it connects again.
What settings do I need to look at, change, etc on the 2860 to see why this is happening? What allows the Plusnet router to connect, but not the 2860?
Thank you for any help.
On my newer Draytek 2762 - I had issues after I did a factory reset to try resolve an issue and found the MTU setting defaults to 1500 but it ideally should be set to 1492. - I'm on fibre to the cabinet.
This caused my web browsing to be very tempermental and mostly unusable until I set the MTU to 1492 and all was good again, someone on here advised me of this Draytek quirk when doing resets and upgrading firmware and the MTU default is wrong for most users.
I'd also consider connecting direct to the test port behind the master socket to ellminate internal wiring causing issues if you don't have a 2 port master socket with phone and dedicated modem socket (which is worth having anyway)
Thanks for the reply. The line is only a year old. I had Openreach visit a year ago as I was having a lot of line drops. They replaced the line back to the pole and installed a new split socket. The MTU is set to 1492 and I installed the latest firmware a few months ago.
My protocol is set to PPPoA not PPPoE (the option under the VC MUX option) - I;m sure you're supposed to use PPPoA for fibre to the cabinet (FTTC) fibre, assuming you connect the VDSL socket directly to the Draytek and don't use a BT Openreach VDSL modem in between socket and Draytek.
Now attention turns to its predecessor, the Draytek 2762. For many the 2762 may still be in use as a dependable unit and offers more or less the same feature set of the newer units. But, does it have enough grunt to support the higher speed profiles that full fibre internet offers, and will its hardware acceleration help boost its potential?
Last of the hurdles was to get data from Asterisk in order to send to Zabbix, however the traditional way of loading the res_snmp.so module in Asterisk was not available, as while the PBX in question utilises Asterisk, its buried under proprietary licensing and a non-standard api, therefore being unable to either add the SNMP module or to query it.
In newer Draytek models the perceived performance of wireless as been lacking based on earlier models such as the rock solid 2860n/plus with reduced range and throughput speeds, in particular poor VoIP performance for my industry.
Previous dabbling with deployment of Unifi access points have yielded trouble fee results, so this would be a quick win. Trouble is, the default AC-Pro and AC-LR are in serious supply shortages at present. Wifi 6 variants have better stock availability but also have a higher purchase cost.
c80f0f1006