M.2 Pcie Specification

[Siri]

PCIExpress (Peripheral Component Interconnect Express), officially abbreviated as PCIe or PCI-e,[1] is a high-speed serial computer expansion bus standard, designed to replace the older PCI, PCI-X and AGP bus standards. It is the common motherboard interface for personal computers' graphics cards, capture cards, sound cards, hard disk drive host adapters, SSDs, Wi-Fi, and Ethernet hardware connections.[2] PCIe has numerous improvements over the older standards, including higher maximum system bus throughput, lower I/O pin count and smaller physical footprint, better performance scaling for bus devices, a more detailed error detection and reporting mechanism (Advanced Error Reporting, AER),[3] and native hot-swap functionality. More recent revisions of the PCIe standard provide hardware support for I/O virtualization.

Conceptually, the PCI Express bus is a high-speed serial replacement of the older PCI/PCI-X bus.[7] One of the key differences between the PCI Express bus and the older PCI is the bus topology; PCI uses a shared parallel bus architecture, in which the PCI host and all devices share a common set of address, data, and control lines. In contrast, PCI Express is based on point-to-point topology, with separate serial links connecting every device to the root complex (host). Because of its shared bus topology, access to the older PCI bus is arbitrated (in the case of multiple masters), and limited to one master at a time, in a single direction. Furthermore, the older PCI clocking scheme limits the bus clock to the slowest peripheral on the bus (regardless of the devices involved in the bus transaction). In contrast, a PCI Express bus link supports full-duplex communication between any two endpoints, with no inherent limitation on concurrent access across multiple endpoints.

In terms of bus protocol, PCI Express communication is encapsulated in packets. The work of packetizing and de-packetizing data and status-message traffic is handled by the transaction layer of the PCI Express port (described later). Radical differences in electrical signaling and bus protocol require the use of a different mechanical form factor and expansion connectors (and thus, new motherboards and new adapter boards); PCI slots and PCI Express slots are not interchangeable. At the software level, PCI Express preserves backward compatibility with PCI; legacy PCI system software can detect and configure newer PCI Express devices without explicit support for the PCI Express standard, though new PCI Express features are inaccessible.

The PCI Express link between two devices can vary in size from one to 16 lanes. In a multi-lane link, the packet data is striped across lanes, and peak data throughput scales with the overall link width. The lane count is automatically negotiated during device initialization and can be restricted by either endpoint. For example, a single-lane PCI Express (x1) card can be inserted into a multi-lane slot (x4, x8, etc.), and the initialization cycle auto-negotiates the highest mutually supported lane count. The link can dynamically down-configure itself to use fewer lanes, providing a failure tolerance in case bad or unreliable lanes are present. The PCI Express standard defines link widths of x1, x2, x4, x8, and x16. Up to and including PCIe 5.0, x12, and x32 links were defined as well but never used.[8] This allows the PCI Express bus to serve both cost-sensitive applications where high throughput is not needed, and performance-critical applications such as 3D graphics, networking (10 Gigabit Ethernet or multiport Gigabit Ethernet), and enterprise storage (SAS or Fibre Channel). Slots and connectors are only defined for a subset of these widths, with link widths in between using the next larger physical slot size.

As a point of reference, a PCI-X (133 MHz 64-bit) device and a PCI Express 1.0 device using four lanes (x4) have roughly the same peak single-direction transfer rate of 1064 MB/s. The PCI Express bus has the potential to perform better than the PCI-X bus in cases where multiple devices are transferring data simultaneously, or if communication with the PCI Express peripheral is bidirectional.

PCI Express devices communicate via a logical connection called an interconnect[9] or link. A link is a point-to-point communication channel between two PCI Express ports allowing both of them to send and receive ordinary PCI requests (configuration, I/O or memory read/write) and interrupts (INTx, MSI or MSI-X). At the physical level, a link is composed of one or more lanes.[9] Low-speed peripherals (such as an 802.11 Wi-Fi card) use a single-lane (x1) link, while a graphics adapter typically uses a much wider and therefore faster 16-lane (x16) link.

The bonded serial bus architecture was chosen over the traditional parallel bus because of the inherent limitations of the latter, including half-duplex operation, excess signal count, and inherently lower bandwidth due to timing skew. Timing skew results from separate electrical signals within a parallel interface traveling through conductors of different lengths, on potentially different printed circuit board (PCB) layers, and at possibly different signal velocities. Despite being transmitted simultaneously as a single word, signals on a parallel interface have different travel duration and arrive at their destinations at different times. When the interface clock period is shorter than the largest time difference between signal arrivals, recovery of the transmitted word is no longer possible. Since timing skew over a parallel bus can amount to a few nanoseconds, the resulting bandwidth limitation is in the range of hundreds of megahertz.

A serial interface does not exhibit timing skew because there is only one differential signal in each direction within each lane, and there is no external clock signal since clocking information is embedded within the serial signal itself. As such, typical bandwidth limitations on serial signals are in the multi-gigahertz range. PCI Express is one example of the general trend toward replacing parallel buses with serial interconnects; other examples include Serial ATA (SATA), USB, Serial Attached SCSI (SAS), FireWire (IEEE 1394), and RapidIO. In digital video, examples in common use are DVI, HDMI, and DisplayPort.

A PCI Express card fits into a slot of its physical size or larger (with x16 as the largest used), but may not fit into a smaller PCI Express slot; for example, a x16 card may not fit into a x4 or x8 slot. Some slots use open-ended sockets to permit physically longer cards and negotiate the best available electrical and logical connection.

The number of lanes actually connected to a slot may also be fewer than the number supported by the physical slot size. An example is a x16 slot that runs at x4, which accepts any x1, x2, x4, x8 or x16 card, but provides only four lanes. Its specification may read as "x16 (x4 mode)", while "mechanical @ electrical" notation (e.g. "x16 @ x4") is also common.[citation needed] The advantage is that such slots can accommodate a larger range of PCI Express cards without requiring motherboard hardware to support the full transfer rate. Standard mechanical sizes are x1, x4, x8, and x16. Cards using a number of lanes other than the standard mechanical sizes need to physically fit the next larger mechanical size (e.g. an x2 card uses the x4 size, or an x12 card uses the x16 size).

The cards themselves are designed and manufactured in various sizes. For example, solid-state drives (SSDs) that come in the form of PCI Express cards often use HHHL (half height, half length) and FHHL (full height, half length) to describe the physical dimensions of the card.[14][15]

For instance, comparing three high-end video cards released in 2020: a Sapphire Radeon RX 5700 XT card measures 135 mm in height (excluding the metal bracket), which exceeds the PCIe standard height by 28 mm,[18] another Radeon RX 5700 XT card by XFX measures 55 mm thick (i.e. 2.7 PCI slots at 20.32 mm), taking up 3 PCIe slots,[19] while an Asus GeForce RTX 3080 video card takes up two slots and measures 140.1 mm 318.5 mm 57.8 mm, exceeding PCI Express' maximum height, length, and thickness respectively.[20]

The following table identifies the conductors on each side of the edge connector on a PCI Express card. The solder side of the printed circuit board (PCB) is the A-side, and the component side is the B-side.[21] PRSNT1# and PRSNT2# pins must be slightly shorter than the rest, to ensure that a hot-plugged card is fully inserted. The WAKE# pin uses full voltage to wake the computer, but must be pulled high from the standby power to indicate that the card is wake capable.[22]

Some cards use two 8-pin connectors, but this has not been standardized yet as of 2018[update], therefore such cards must not carry the official PCI Express logo. This configuration allows 375 W total (1 75 W + 2 150 W) and will likely be standardized by PCI-SIG with the PCI Express 4.0 standard.[needs update] The 8-pin PCI Express connector could be confused with the EPS12V connector, which is mainly used for powering SMP and multi-core systems. The power connectors are variants of the Molex Mini-Fit Jr. series connectors.[30]

The 16-pin 12VHPWR connector is a standard for connecting graphics processing units (GPUs) to computer power supplies. It was introduced in 2022 to supersede the previous 6- and 8-pin power connectors for GPUs. The primary aim was to cater to the increasing power requirements of high-performance GPUs. It was replaced by a minor revision called 12V-2x6, which changed the connector to ensure that the sense pins only make contact if the power pins are seated properly.

Due to different dimensions, PCI Express Mini Cards are not physically compatible with standard full-size PCI Express slots; however, passive adapters exist that let them be used in full-size slots.[37]

Dimensions of PCI Express Mini Cards are 30 mm 50.95 mm (width length) for a Full Mini Card. There is a 52-pin edge connector, consisting of two staggered rows on a 0.8 mm pitch. Each row has eight contacts, a gap equivalent to four contacts, then a further 18 contacts. Boards have a thickness of 1.0 mm, excluding the components. A "Half Mini Card" (sometimes abbreviated as HMC) is also specified, having approximately half the physical length of 26.8 mm.

3a8082e126