Board reset before I login
112 views
Skip to first unread message
Errol Blanco Valverde
Jan 26, 2011, 3:08:55 PM1/26/11
to Technexion Thunderpack
Hi, I was working with my board and I was use fine the LCD (with
touchscreen); the usb has some issues, and sometimes it didn't
recognize my keyboard, but I notice that it happens only when I
connect the board to a LAN wired network. Until here, I powered the
board by USB. After a small search, I figured out that was a power
problem, so I bought a AC-DC adaptor, but I has to mount a 5V
regulator because the adaptor is 4.5V or 6V.
It works for 2 weeks but after that my board suddenly turning off, so
I restore my board; but after i copy the root file system and reset it
to boot from nand, give some usb errors, and I can't login because it
reset again. Here is what my board shows in console (through serial
port).
I need that someone advice me, because i don't know which is the
problem. Is this a hardware or a software issue? What should I do?
------------------------------------------------------------------------------------------------------------------------------------------------------------------
Texas Instruments X-Loader 1.4.2 (Feb 19 2009 - 12:01:24)
Loading u-boot.bin from nand
U-Boot 2009.11 (Nov 01 2010 - 15:22:45)
OMAP3430/3530-GP ES3.1, CPU-OPP2 L3-165MHz
OMAP3 TAO-3530 board + LPDDR/NAND
I2C: ready
DRAM: 128 MB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Die ID #1a4e000400000000040365fa0800a00a
Net: No ethernet found.
Hit any key to stop autoboot: 2 1 0
No MMC card found
Booting from nand ...
NAND read: device 0 offset 0x280000, size 0x400000
Skipping bad block 0x004c0000
4194304 bytes read: OK
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-2.6.32
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2439396 Bytes = 2.3 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing
Linux............................................................
Linux version 2.6.32 (root@AIR) (gcc version 4.4.1 (Sourcery G++ Lite
2010q1-201
CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: OMAP3 TAO-3530 Series
Memory policy: ECC disabled, Data cache writeback
OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
Reserving 4194304 bytes SDRAM for VRAM
Built 1 zonelists in Zone order, mobility grouping on. Total pages:
32512
Kernel command line: console=ttyS2,115200n8 root=/dev/mtdblock4 rw
rootfstype=j2
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 120760KB available (4260K code, 352K data, 172K init, 0K
highmem)
Hierarchical RCU implementation.
NR_IRQS:402
Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
Reprogramming SDRC clock to 332000000 Hz
GPMC revision 5.0
IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
OMAP GPIO hardware version 2.5
OMAP clockevent source: GPTIMER1 at 32768 Hz
Console: colour dummy device 80x30
Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
Found NAND on CS0
Registering NAND on CS0
OMAP DMA hardware revision 4.0
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
twl4030: PIH (irq 7) chaining IRQs 368..375
twl4030: power (irq 373) chaining IRQs 376..383
twl4030: gpio (irq 368) chaining IRQs 384..401
regulator: VUSB1V5: 1500 mV normal standby
regulator: VUSB1V8: 1800 mV normal standby
regulator: VUSB3V1: 3100 mV normal standby
twl4030_usb twl4030_usb: Initialized TWL4030 USB module
regulator: VMMC1: 1850 <--> 3150 mV normal standby
regulator: VDAC: 1800 mV normal standby
regulator: VPLL2: 1800 mV normal standby
regulator: VMMC2: 1850 <--> 3150 mV normal standby
regulator: VSIM: 1800 <--> 3000 mV normal standby
i2c_omap i2c_omap.2: bus 2 rev3.12 at 100 kHz
i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource 32k_counter
musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NetWinder Floating Point Emulator V0.97 (double precision)
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 236
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Generic Backlight Driver Initialized.
OMAP DSS rev 2.0
OMAP DISPC rev 3.0
OMAP VENC rev 2
OMAP DSI rev 1.0
LG LB043WQ2 Probe
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
console [ttyS2] enabled
brd: module loaded
loop: module loaded
omap2-nand driver initializing
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB
1,8V 16-b)
cmdlinepart partition parsing not available
Creating 5 MTD partitions on "omap2-nand":
0x000000000000-0x000000080000 : "X-Loader"
0x000000080000-0x000000260000 : "U-Boot"
0x000000260000-0x000000280000 : "U-Boot Env"
0x000000280000-0x000000680000 : "Kernel"
0x000000680000-0x000010000000 : "File System"
usbcore: registered new interface driver smsc95xx
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OMAP-EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.32 ehci_hcd
usb usb1: SerialNumber: ehci-omap.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbtest
g_ether gadget: using random self ethernet address
g_ether gadget: using random host ethernet address
usb0: MAC 0a:9c:82:28:f3:66
usb0: HOST MAC de:89:b1:f4:72:5e
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 2
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: MUSB HDRC host driver
usb usb2: Manufacturer: Linux 2.6.32 musb-hcd
usb usb2: SerialNumber: musb_hdrc
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ads7846 spi1.0: touchscreen, irq 296
input: ADS7846 Touchscreen as /devices/platform/omap2_mcspi.1/spi1.0/
input/inpu0
twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
twl_rtc twl_rtc: Power up reset detected.
twl_rtc twl_rtc: Enabling TWL-RTC.
i2c /dev entries driver
OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
Register omap_hsmmc_device 0
Register omap_hsmmc_device 1
regulator_check_voltage: operation not allowed for VMMC2
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.21.
usbcore: registered new interface driver snd-usb-audio
usb 1-2: new high speed USB device using ehci-omap and address 2
No device for DAI omap-mcbsp-dai-0
No device for DAI omap-mcbsp-dai-1
No device for DAI omap-mcbsp-dai-2
No device for DAI omap-mcbsp-dai-3
No device for DAI omap-mcbsp-dai-4
OMAP3 TAO-3530 SoC init
asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
ALSA device list:
#0: omap3tao3530 (twl4030)
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
lib80211: common routines for IEEE802.11 drivers
Power Management for TI OMAP3.
SmartReflex driver initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev
1
Console: switching to colour frame buffer device 60x34
usb 1-2: New USB device found, idVendor=05e3, idProduct=0608
usb 1-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-2: Product: USB2.0 Hub
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 4 ports detected
regulator_init_complete: incomplete constraints, leaving VDAC on
twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC
(946684800)
usb 1-2.1: new high speed USB device using ehci-omap and address 3
usb 1-2.1: New USB device found, idVendor=0424, idProduct=9500
usb 1-2.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
smsc95xx v1.0.4
eth0: register 'smsc95xx' at usb-ehci-omap.0-2.1, smsc95xx USB 2.0
Ethernet, 00b
JFFS2 notice: (1) jffs2_build_xattr_subsystem: complete building xattr
subsyste.
VFS: Mounted root (jffs2 filesystem) on device 31:4.
Freeing init memory: 172K
INIT: version 2.86 booting
Please wait: booting...
Starting udev
udev: starting version 141
Remounting root file system...
Unknown HZ value! (94) Assume 100.
root: mount: mount point /proc/bus/usb does not exist
ALSA: Restoring mixer settings...
Configuring network interfaces... done.
Starting portmap daemon: portmap.
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
Wed Nov 11 14:12:00 GMT 2009
INIT: Entering runlevel: 5
Starting system message bus: Unknown username "system" in message bus
configurae dbus.
Starting Hardware abstraction layer hald
Starting Connection Manager
Starting Dropbear SSH server: dropbear.
Starting advanced power management daemon: No APM support in kernel
(failed.)
Starting syslogd/klogd: done
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
[ ok ]
libertas_sdio: Libertas SDIO driver
libertas_sdio: Copyright Pierre Ossman
regulator_check_voltage: operation not allowed for VMMC2
Starting GPE display manager: gpe-dm
Ondemand
mmc1: new SDIO card at address 0001
usb 1-2: USB disconnect, address 2
usb 1-2.1: USB disconnect, address 3
eth0: unregister 'smsc95xx' usb-ehci-omap.0-2.1, smsc95xx USB 2.0
Ethernet
usb 1-2: new high speed USB device using ehci-omap and address 4
.-------.
| | .-.
| | |-----.-----.-----.| | .----..-----.-----.
| | | __ | ---'| '--.| .-'| | |
| | | | | |--- || --'| | | ' | | | |
'---'---'--'--'--. |-----''----''--' '-----'-'-'-'
-' |
'---'
The Angstrom Distribution taodemo ttyS2
Angstrom 2009.X-test-20091029 taodemo ttyS2
taodemo login: usb 1-2: New USB device found, idVendor=05e3,
idProduct=0608
usb 1-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-2: Product: USB2.0 Hub
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 4 ports detected
usb 1-2.1: new high speed USB device using ehci-omap and address 5
usb 1-2.1: New USB device found, idVendor=0424, idProduct=9500
usb 1-2.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
smsc95xx v1.0.4
usb%d: usbnet_get_endpoints failed: -71
smsc95xx: probe of 1-2.1:1.0 failed with error -71
usb 1-2: USB disconnect, address 4
usb 1-2.1: USB disconnect, address 5
usb 1-2: new high speed USB device using ehci-omap and address 6
libertas: 00:1f:7b:35:00:58, fw 9.70.4p0, cap 0x00000303
libertas: wlan0: Marvell WLAN 802.11 adapter
usb 1-2: device not accepting address 6, error -71
usb 1-2: new high speed USB device using ehci-omap and address 7
hub 1-0:1.0: unable to enumerate USB device on port 2
Texas Instruments X-Loader 1.4.2 (Feb 19 2009 - 12:01:24)
Loading u-boot.bin from nand
U-Boot 2009.11 (Nov 01 2010 - 15:22:45)
OMAP3430/3530-GP ES3.1, CPU-OPP2 L3-165MHz
OMAP3 TAO-3530 board + LPDDR/NAND
I2C: ready
DRAM: 128 MB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Die ID #1a4e000400000000040365fa0800a00a
Net: No ethernet found.
Hit any key to stop autoboot: 2
------------------------------------------------------------------------------------------------------------------------------------------------------
touchscreen); the usb has some issues, and sometimes it didn't
recognize my keyboard, but I notice that it happens only when I
connect the board to a LAN wired network. Until here, I powered the
board by USB. After a small search, I figured out that was a power
problem, so I bought a AC-DC adaptor, but I has to mount a 5V
regulator because the adaptor is 4.5V or 6V.
It works for 2 weeks but after that my board suddenly turning off, so
I restore my board; but after i copy the root file system and reset it
to boot from nand, give some usb errors, and I can't login because it
reset again. Here is what my board shows in console (through serial
port).
I need that someone advice me, because i don't know which is the
problem. Is this a hardware or a software issue? What should I do?
------------------------------------------------------------------------------------------------------------------------------------------------------------------
Texas Instruments X-Loader 1.4.2 (Feb 19 2009 - 12:01:24)
Loading u-boot.bin from nand
U-Boot 2009.11 (Nov 01 2010 - 15:22:45)
OMAP3430/3530-GP ES3.1, CPU-OPP2 L3-165MHz
OMAP3 TAO-3530 board + LPDDR/NAND
I2C: ready
DRAM: 128 MB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Die ID #1a4e000400000000040365fa0800a00a
Net: No ethernet found.
Hit any key to stop autoboot: 2 1 0
No MMC card found
Booting from nand ...
NAND read: device 0 offset 0x280000, size 0x400000
Skipping bad block 0x004c0000
4194304 bytes read: OK
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-2.6.32
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2439396 Bytes = 2.3 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing
Linux............................................................
Linux version 2.6.32 (root@AIR) (gcc version 4.4.1 (Sourcery G++ Lite
2010q1-201
CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: OMAP3 TAO-3530 Series
Memory policy: ECC disabled, Data cache writeback
OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
Reserving 4194304 bytes SDRAM for VRAM
Built 1 zonelists in Zone order, mobility grouping on. Total pages:
32512
Kernel command line: console=ttyS2,115200n8 root=/dev/mtdblock4 rw
rootfstype=j2
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 120760KB available (4260K code, 352K data, 172K init, 0K
highmem)
Hierarchical RCU implementation.
NR_IRQS:402
Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
Reprogramming SDRC clock to 332000000 Hz
GPMC revision 5.0
IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
OMAP GPIO hardware version 2.5
OMAP clockevent source: GPTIMER1 at 32768 Hz
Console: colour dummy device 80x30
Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
Found NAND on CS0
Registering NAND on CS0
OMAP DMA hardware revision 4.0
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
twl4030: PIH (irq 7) chaining IRQs 368..375
twl4030: power (irq 373) chaining IRQs 376..383
twl4030: gpio (irq 368) chaining IRQs 384..401
regulator: VUSB1V5: 1500 mV normal standby
regulator: VUSB1V8: 1800 mV normal standby
regulator: VUSB3V1: 3100 mV normal standby
twl4030_usb twl4030_usb: Initialized TWL4030 USB module
regulator: VMMC1: 1850 <--> 3150 mV normal standby
regulator: VDAC: 1800 mV normal standby
regulator: VPLL2: 1800 mV normal standby
regulator: VMMC2: 1850 <--> 3150 mV normal standby
regulator: VSIM: 1800 <--> 3000 mV normal standby
i2c_omap i2c_omap.2: bus 2 rev3.12 at 100 kHz
i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource 32k_counter
musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NetWinder Floating Point Emulator V0.97 (double precision)
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 236
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Generic Backlight Driver Initialized.
OMAP DSS rev 2.0
OMAP DISPC rev 3.0
OMAP VENC rev 2
OMAP DSI rev 1.0
LG LB043WQ2 Probe
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
console [ttyS2] enabled
brd: module loaded
loop: module loaded
omap2-nand driver initializing
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB
1,8V 16-b)
cmdlinepart partition parsing not available
Creating 5 MTD partitions on "omap2-nand":
0x000000000000-0x000000080000 : "X-Loader"
0x000000080000-0x000000260000 : "U-Boot"
0x000000260000-0x000000280000 : "U-Boot Env"
0x000000280000-0x000000680000 : "Kernel"
0x000000680000-0x000010000000 : "File System"
usbcore: registered new interface driver smsc95xx
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OMAP-EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.32 ehci_hcd
usb usb1: SerialNumber: ehci-omap.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbtest
g_ether gadget: using random self ethernet address
g_ether gadget: using random host ethernet address
usb0: MAC 0a:9c:82:28:f3:66
usb0: HOST MAC de:89:b1:f4:72:5e
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 2
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: MUSB HDRC host driver
usb usb2: Manufacturer: Linux 2.6.32 musb-hcd
usb usb2: SerialNumber: musb_hdrc
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ads7846 spi1.0: touchscreen, irq 296
input: ADS7846 Touchscreen as /devices/platform/omap2_mcspi.1/spi1.0/
input/inpu0
twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
twl_rtc twl_rtc: Power up reset detected.
twl_rtc twl_rtc: Enabling TWL-RTC.
i2c /dev entries driver
OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
Register omap_hsmmc_device 0
Register omap_hsmmc_device 1
regulator_check_voltage: operation not allowed for VMMC2
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.21.
usbcore: registered new interface driver snd-usb-audio
usb 1-2: new high speed USB device using ehci-omap and address 2
No device for DAI omap-mcbsp-dai-0
No device for DAI omap-mcbsp-dai-1
No device for DAI omap-mcbsp-dai-2
No device for DAI omap-mcbsp-dai-3
No device for DAI omap-mcbsp-dai-4
OMAP3 TAO-3530 SoC init
asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
ALSA device list:
#0: omap3tao3530 (twl4030)
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
lib80211: common routines for IEEE802.11 drivers
Power Management for TI OMAP3.
SmartReflex driver initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev
1
Console: switching to colour frame buffer device 60x34
usb 1-2: New USB device found, idVendor=05e3, idProduct=0608
usb 1-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-2: Product: USB2.0 Hub
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 4 ports detected
regulator_init_complete: incomplete constraints, leaving VDAC on
twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC
(946684800)
usb 1-2.1: new high speed USB device using ehci-omap and address 3
usb 1-2.1: New USB device found, idVendor=0424, idProduct=9500
usb 1-2.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
smsc95xx v1.0.4
eth0: register 'smsc95xx' at usb-ehci-omap.0-2.1, smsc95xx USB 2.0
Ethernet, 00b
JFFS2 notice: (1) jffs2_build_xattr_subsystem: complete building xattr
subsyste.
VFS: Mounted root (jffs2 filesystem) on device 31:4.
Freeing init memory: 172K
INIT: version 2.86 booting
Please wait: booting...
Starting udev
udev: starting version 141
Remounting root file system...
Unknown HZ value! (94) Assume 100.
root: mount: mount point /proc/bus/usb does not exist
ALSA: Restoring mixer settings...
Configuring network interfaces... done.
Starting portmap daemon: portmap.
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
Wed Nov 11 14:12:00 GMT 2009
INIT: Entering runlevel: 5
Starting system message bus: Unknown username "system" in message bus
configurae dbus.
Starting Hardware abstraction layer hald
Starting Connection Manager
Starting Dropbear SSH server: dropbear.
Starting advanced power management daemon: No APM support in kernel
(failed.)
Starting syslogd/klogd: done
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
[ ok ]
libertas_sdio: Libertas SDIO driver
libertas_sdio: Copyright Pierre Ossman
regulator_check_voltage: operation not allowed for VMMC2
Starting GPE display manager: gpe-dm
Ondemand
mmc1: new SDIO card at address 0001
usb 1-2: USB disconnect, address 2
usb 1-2.1: USB disconnect, address 3
eth0: unregister 'smsc95xx' usb-ehci-omap.0-2.1, smsc95xx USB 2.0
Ethernet
usb 1-2: new high speed USB device using ehci-omap and address 4
.-------.
| | .-.
| | |-----.-----.-----.| | .----..-----.-----.
| | | __ | ---'| '--.| .-'| | |
| | | | | |--- || --'| | | ' | | | |
'---'---'--'--'--. |-----''----''--' '-----'-'-'-'
-' |
'---'
The Angstrom Distribution taodemo ttyS2
Angstrom 2009.X-test-20091029 taodemo ttyS2
taodemo login: usb 1-2: New USB device found, idVendor=05e3,
idProduct=0608
usb 1-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-2: Product: USB2.0 Hub
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 4 ports detected
usb 1-2.1: new high speed USB device using ehci-omap and address 5
usb 1-2.1: New USB device found, idVendor=0424, idProduct=9500
usb 1-2.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
smsc95xx v1.0.4
usb%d: usbnet_get_endpoints failed: -71
smsc95xx: probe of 1-2.1:1.0 failed with error -71
usb 1-2: USB disconnect, address 4
usb 1-2.1: USB disconnect, address 5
usb 1-2: new high speed USB device using ehci-omap and address 6
libertas: 00:1f:7b:35:00:58, fw 9.70.4p0, cap 0x00000303
libertas: wlan0: Marvell WLAN 802.11 adapter
usb 1-2: device not accepting address 6, error -71
usb 1-2: new high speed USB device using ehci-omap and address 7
hub 1-0:1.0: unable to enumerate USB device on port 2
Texas Instruments X-Loader 1.4.2 (Feb 19 2009 - 12:01:24)
Loading u-boot.bin from nand
U-Boot 2009.11 (Nov 01 2010 - 15:22:45)
OMAP3430/3530-GP ES3.1, CPU-OPP2 L3-165MHz
OMAP3 TAO-3530 board + LPDDR/NAND
I2C: ready
DRAM: 128 MB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Die ID #1a4e000400000000040365fa0800a00a
Net: No ethernet found.
Hit any key to stop autoboot: 2
------------------------------------------------------------------------------------------------------------------------------------------------------
Reply all
Reply to author
Forward
0 new messages