Fw: AW: AW: Two question in retrieve RM data by TCL script

[wangke81168720]

关于之前我按照TCL文档中的全例句提取影响线竖标值不成功的问题，经确认是他们的 TCL 帮助文档编写的失误，

即先 MAXMz 应改为 Mz，  and so on.

 

附件中也给出了正确的做法。

 

---

wangke81168720

2009-03-04

---

发件人： Joerg...@bentley.com

发送时间： 2009-03-04 01:54:30

收件人： wa...@nbsunsoft.com

抄送： sup...@tdv.at

主题： AW: AW: Two question in retrieve RM data by TCL script

 

Dear Wangke,

 

in addition to the mail from Johann, find enclosed an example how to use the needed command.

 

Best Regards,

Joerg Sello

Graz, Bentley Systems Austria

 

 

 

 

Von: Johann Stampler
Gesendet: Dienstag, 03. M?rz 2009 18:09
An: wangk
Cc: Joerg Sello; sup...@tdv.at
Betreff: AW: AW: Two question in retrieve RM data by TCL script
Wichtigkeit: Niedrig

 

Dear Wangke,

This is a bug in the description. Influence lines have only one value for each point, i.e. you must enter Mz instead of MaxMz. I will change the documentation accordingly.

As a result you will get an array containing alternatively the position along the lane and the corresponding influence value which can be positive or negative.

Regards,

Johann Stampler

 

Von: wangk [mailto:wa...@nbsunsoft.com]
Gesendet: Montag, 02. M?rz 2009 17:06
An: Johann Stampler
Betreff: Re: AW: Two question in retrieve RM data by TCL script

 

Dear Johann Stampler

 

     In the attachment ,it is the  project tcl ,  and  the testing  tcl for retrieve influence line result.

When I finish  the project calculation,   I  run the "temp.tcl"   in  "File" menu,   some  error messages shows as I described before,    can  you  help to find  what is  the right  script  for this project tcl file, thanks .

 

　　

 

======== 2009-03-02 23:40:51 您在来信中写道： ========

 

Dear Wangke, I could not reproduce your problem. Specified elements exist? Influence lines have been created? Please send the project tcl and the tcl’s you created for getting influence line information and reinforcement information. Regards, Johann Stampler _____________________________________________ Von: Evelyn Sprajc Gesendet: Montag, 02. M?rz 2009 11:28 An: Johann Stampler Betreff: Two question in retrieve RM data by TCL script ? < Datei: figure1.GIF >>  < Datei: figure.GIF >>  < Datei: figure2.GIF >> ----- Original Message ----- From: wangk To: Support Cc: Jackie Sent: Monday, March 02, 2009 9:56 AM Subject: Two question in retrieve RM data by TCL script Dear Sir ? 　　1. To retrieve results from influence line? from? lane or *.inf file,? I? used wrrote the TCL as below: ? BEAM 104 GETINFLINE 1 AT END MAXMz but? I? get? error message as shown in? figure.gif ,?? the script above is wrote like in? TCL Guide, as shown in? figure1.gif,? can you? check? if? the guide have some? error? or? I have made some mistake ? ? ????? 2.? A colleague? is trying to? retrieve the? area of? a? bending reinforcement , he? followed? the TCL? Guide as shown in figure2.gif ,? and? she? always get? "0"?? not matter?? she? input A1? or? calculated A2 . the script she wrotes is as below: set area?? [BEAM 105 REINF_BENDING? "AttSet1"? GETAREA??? ] ? ? BTW,? retrieve influence result by TCL? is? needed tomorrow,? It's? helpful? you? reply about it? later in today. ? ? 　　　　　　　　 Sincerely ?　　　　　　??????????WangKe ???????????????????????wa...@nbsunsoft.com   　　　　　　　　　　? 　? ?2009-03-02 ? --------------------------------------------------------- ? Sunshine software development centre,Jiangdong,Ningbo Tel：0574 87771215 Mobile：13780014258 sup...@nbsunsoft.com http://www.nbsunsoft.com

= = = = = = = = = = = = = = = = = = = = = =

　　　　　　　　致
礼！

 

　　　　　　　　　　　　　　wangk

　　　　　　　　　　　　　　wa...@nbsunsoft.com

　　　　　　　　　　　　　　　2009-03-03