flashing tasmota on sonoff pow origin/elite (powr320D)

[Bryan Bradford]

I have (I thought) successfully flashed the device. Windows 10, Web flasher, Tasmota(english), ESP32. It connects and installs, finishes up, and says complete. When I apply mains, I get nothing. No LEDs or web interface. If I power it with just the usb serial, I can connect to the serial output and I can see that it is spontaneously rebooting. Here is the output: (repeating constantly).

rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:184
load:0x40078000,len:12732
ho 0 tail 12 room 4
load:0x40080400,len:2908
entry 0x400805c4

00:00:00.003-215/51 HDW: ESP32-D0WD-V3 v3.0
00:00:00.036-214/50 UFS: FlashFS mounted with 308 kB free
00:00:00.054 CFG: Loaded from File, Count 2
00:00:00.064 QPC: Count 1
00:00:00.486 BRY: Berry initialized, RAM used 5164 bytes
00:00:00.504 TFS: File '.drvset003' not found
00:00:00.512 Project tasmota - Tasmota Version 13.2.0.2(tasmota32)-2_0_14(2023-11-07T19:32:13)
00:00:00.818 WIF: WifiManager active for 3 minutes
ets Jul 29 2019 12:21:46

Does anyone have some suggestions on what I have done wrong?
Did I use the correct firmware (Tasmota english) for esp32?

Thanks!
Bryan

[Philip Knowles]

It's getting to the point where it's waiting for you to put in your WiFi credentials (192.168.4.1) it will wait for 3 minutes then reboot 

Sent from Outlook for Android

---

From: sonof...@googlegroups.com <sonof...@googlegroups.com> on behalf of Bryan Bradford <brya...@gmail.com>
Sent: Thursday, November 9, 2023 9:44:47 PM
To: TasmotaUsers <sonof...@googlegroups.com>
Subject: flashing tasmota on sonoff pow origin/elite (powr320D)

 

--
You received this message because you are subscribed to the Google Groups "TasmotaUsers" group.
To unsubscribe from this group and stop receiving emails from it, send an email to sonoffusers...@googlegroups.com.
To view this discussion on the web, visit https://groups.google.com/d/msgid/sonoffusers/e0407059-2004-4b4c-95cf-e6f74696f9adn%40googlegroups.com.

[ford.pre...@gmail.com]

...I had the same problem with a batch of POWR320D.

This was the first batch I  had to convert from stock firmware after  tasmota v13was published.
The flash process reports a successful flash, but the AP from wifi-manager never shows up.

On the serial it reports, that its waiting for 3 mins, but is rebooting instantly right after that, over and over again.

So I tried flashing v12.5.0 which still has the old dual partition layout, not safeboot like with v13.

That worked fine and I then used partition wizard to migrate to safeboot scheme and v13.

[Philip Knowles]

Please raise as an issue (if it's not already been raised). It won't get fixed unless people tell the developers.

Sent from Outlook for Android

---

From: sonof...@googlegroups.com <sonof...@googlegroups.com> on behalf of ford.pre...@gmail.com <ford.pre...@gmail.com>
Sent: Friday, November 10, 2023 6:37:05 AM
To: TasmotaUsers <sonof...@googlegroups.com>
Subject: Re: flashing tasmota on sonoff pow origin/elite (powr320D)

 

To view this discussion on the web, visit https://groups.google.com/d/msgid/sonoffusers/5f49257b-d53b-480b-9703-f3beb036ab94n%40googlegroups.com.