Fx5-232adp Manual
Tamela
*2When the connected device communicates with multiple MELSOFT (Mitsubishi Electric's engineering software products such as GX Works3) by TCP, the same number of settings as the connected MELSOFT (MELSOFT connected device settings) need to be set in the parameter settings of the connected device. For details, refer to the manual of the connected Mitsubishi Electric product.
Hardware ManualManual NumberJY997D66701RevisionCDateApril 2021This manual describes the part names, dimensions, installation, and specifications of the product. Before use, read this manual and manuals of relevant products fully to acquire proficiency in handling and operating the product. Make sure to learn all the product information, safety information, and precautions. And, store this manual in a safe place so that you can take it out and read it whenever necessary. Always forward it to the end user. Registration:The company names, system names and product names mentioned in this manual are either registered trademarks or trademarks of their respective companies. In some cases, trademark symbols such as '' or '' are not specified in this manual.
- Installation in EnclosureProgrammable controllers are open-type devices that must be installed and used within conductive control cabinets. Please use the programmable controller while installed within a conductive shielded control cabinet. Installation within a control cabinet greatly affects the safety of the system and aids in shielding noise from the programmable controller.Control cabinet
- The control cabinet must be conductive.Ground the control cabinet with the thickest possible grounding cable.To ensure that there is electric contact between the control cabinet and its door, connect the cabinet and its doors with thick wires.In order to suppress the leakage of radio waves, the control cabinet structure must have minimal openings. Also, wrap the cable holes with a shielding cover or other shielding devices.The gap between the control cabinet and its door must be as small as possible by attaching EMI gaskets between them.
- Cables
- ake sure to use shielded cables as cables pulled out of the control cabinet.
- Connect the shield such as shielded cables and shielding covers to the grounded control cabinet.
- It is possible that the accuracy temporarily fluctuates within 10 %.
FX5-4AD-TC-ADP expansion adapter for thermocouple temperature sensor input (hereinafter called TC-ADP) is an expansion adapter for connecting a thermocouple (K, J, T, B, R, S) temperature sensor, and measuring 4 channels of temperature.
WIRING PRECAUTIONS
- Make sure to cut off all phases of the power supply externally before attempting installation or wiring work. Failure to do so may cause electric shock or damage to the product.
- Make sure to properly wire to the terminal block (European type) in accordance with the following precautions. Failure to do so may cause electric shock, equipment failures, a short-circuit, wire breakage, malfunctions, or damage to the product.
- The disposal size of the cable end should follow the dimensions described in the manual.
- Tightening torque should follow the specifications in the manual.
- Twist the ends of stranded wires and make sure that there are no loose wires.
- Do not solder-plate the electric wire ends.
- Do not connect more than the specified number of wires or electric wires of unspecified size.
- Affix the electric wires so that neither the terminal block nor the connected parts are directly stressed.
- When drilling screw holes or wiring, make sure cutting or wire debris does not enter the ventilation slits. Failure to do so may cause fire, equipment failures or malfunctions.Make sure to observe the following precautions in order to prevent any damage to the machinery or accidents due to malfunction of the PLC caused by abnormal data written to the PLC due to the effects of noise:1) Do not bundle the power line or analog input/output cable together with or lay them close to the main circuit, high-voltage line, load line or power line. As a guideline, lay the power line, control line and communication cables at least 100 mm away from the main circuit, high-voltage line, load line or power line.2) Ground the shield of the analog input/output cable at one point on the signal receiving side. However, do not use common grounding with heavy electrical systems.
- Cable End Treatment And Tightening Torque1.1 European type terminal block1) Wiring type Use shielded compensating lead wire that is suitable for the thermocouple type when wiring the thermocouple.2) Suitable wiringNo. of wire per terminal
STARTUP AND MAINTENANCE PRECAUTIONS
- Do not disassemble or modify the PLC.Doing so may cause fire, equipment failures, or malfunctions.For repair, contact your local Mitsubishi Electric representative.Do not drop the product or exert strong impact to it.Doing so may cause damage.
- Please contact a certified electronic waste disposal company for the environmentally safe recycling and disposal of your device.
- The product is a precision instrument. During transportation, avoid impacts larger than those specified in the general specifications by using dedicated packaging boxes and shock-absorbing palettes. Failure to do so may cause failures in the product. After transportation, verify operation of the product and check for damage of the mounting part, etc.
- Applicable CPU ModuleModel name