MP118 FXO Config

[North Blue]

Good Morning.

Where can I find resource config guide for AudioCodes MP118 FXO Version 6.60?

Would very much appreciate some guidance on this, thanks.

Best regards...

[Gerald Drouillard]

This is about 10 yrs old...

;**************

;** Ini File **

;**************

;Board: MP-118 FXO

;Serial Number: 1431829

;Slot Number: 1

;Software Version: 5.40A.013.004

;DSP Software Version: 204IM => 540.14

;Board IP Address: 192.168.10.7

;Board Subnet Mask: 255.255.255.0

;Board Default Gateway: 192.168.10.1

;Ram size: 32M   Flash size: 8M

;Num DSPs: 2  Num DSP channels: 8

;Profile: NONE

;-----------------------------------------

[SYSTEM Params]

DNSPriServerIP = 192.168.10.6

SyslogServerIP = 10.1.1.89

VXMLFIleName = ''

NTPServerIP = 192.168.10.6

NTPUpdateInterval = 3600

VoiceMenuPassword = 'disable'

[BSP Params]

PCMLawSelect = 3

LocalMediaDefaultGW = 192.168.1.1

LocalMediaIPAddress = 192.168.1.7

LocalMediaSubnetMask = 255.255.255.0

LocalControlIPAddress = 192.168.1.7

LocalControlSubnetMask = 255.255.255.0

StorageServerNetworkAddress = 255.255.255.255

[ATM Params]

[Analog Params]

MinFlashHookTime = 100

FXSLoopCharacteristicsFilename = 'MP11x-02-1-FXS_16KHZ.dat'

[ControlProtocols Params]

AdminStateLockControl = 0

[MGCP Params]

[MEGACO Params]

EP_Num_0 = 0

EP_Num_1 = 1

EP_Num_2 = 0

EP_Num_3 = 0

EP_Num_4 = 0

[PSTN Params]

[SS7 Params]

[Voice Engine Params]

VoicePromptsFileName = ''

InputGain = 15

BrokenConnectionEventTimeout = 100

RFC2833PayloadType = 101

FarEndDisconnectSilenceMethod = 0

FarEndDisconnectSilencePeriod = 120

CallProgressTonesFilename = 'usa_tones_12.dat'

[WEB Params]

[SIP Params]

ENABLECALLERID = 1

MAXDIGITS = 3

ISPROXYUSED = 1

ISWAITFORDIALTONE = 1

ISTWOSTAGEDIAL = 0

ENABLECURRENTDISCONNECT = 1

ENABLEREVERSALPOLARITY = 1

CHANNELSELECTMODE = 1

GWDEBUGLEVEL = 5

ENABLEEARLYMEDIA = 1

ISUSERPHONE = 0

PROXYNAME = '192.168.10.6'

PASSWORD = ''

ENABLESILENCEDISCONNECT = 1

PROGRESSINDICATOR2IP = -1

ALWAYSSENDTOPROXY = 1

CDRSYSLOGSERVERIP = 0.0.0.0

PSTNALERTTIMEOUT = 180

PREFERROUTETABLE = 1

ISFAXUSED = 1

DISCONNECTONDIALTONE = 1

ENABLETCPCONNECTIONREUSE = 0

ENABLESEMIATTENDEDTRANSFER = 1

REDUNDANTROUTINGMODE = 2

[SCTP Params]

[VXML Params]

[IPsec Params]

[Audio Staging Params]

;

;  *** TABLE DspTemplates ***

; This table contains hidden elements and will not be exposed.

; This table exists on board and will be saved during restarts

;

;

;  *** TABLE PREFIX ***

; 

;

[ PREFIX ]

FORMAT PREFIX_Index = PREFIX_DestinationPrefix, PREFIX_DestAddress, PREFIX_SourcePrefix, PREFIX_ProfileId, PREFIX_MeteringCode, PREFIX_SrcIPGroupID, PREFIX_DestHostPrefix, PREFIX_DestIPGroupID, PREFIX_SrcHostPrefix, PREFIX_TransportType, PREFIX_SrcTrunkGroupID;

PREFIX 0 = *, 192.168.10.6, *, 1, 255, -1, , -1, , -1, -1;

[ \PREFIX ]

;

;  *** TABLE CoderName ***

; 

;

[ CoderName ]

FORMAT CoderName_Index = CoderName_Type, CoderName_PacketInterval, CoderName_rate, CoderName_PayloadType, CoderName_Sce;

CoderName 0 = g711Ulaw64k, 20, 0, 255, 0;

CoderName 1 = g711Alaw64k, 20, 0, 255, 0;

CoderName 2 = g729, 20, 0, 255, 0;

CoderName 5 = g711Ulaw64k, 20, 0, 255, 0;

CoderName 6 = g711Alaw64k, 20, 0, 255, 0;

CoderName 7 = g729, 20, 0, 255, 0;

[ \CoderName ]

;

;  *** TABLE TrunkGroup ***

; 

;

[ TrunkGroup ]

FORMAT TrunkGroup_Index = TrunkGroup_TrunkGroupNum, TrunkGroup_FirstTrunkId, TrunkGroup_FirstBChannel, TrunkGroup_LastBChannel, TrunkGroup_FirstPhoneNumber, TrunkGroup_ProfileId, TrunkGroup_LastTrunkId, TrunkGroup_Module;

TrunkGroup 0 = 1, 255, 1, 8, 100, 1, 255, 255;

[ \TrunkGroup ]

;

;  *** TABLE PstnPrefix ***

; 

;

[ PstnPrefix ]

FORMAT PstnPrefix_Index = PstnPrefix_DestPrefix, PstnPrefix_TrunkGroupId, PstnPrefix_SourcePrefix, PstnPrefix_SourceAddress, PstnPrefix_ProfileId, PstnPrefix_SrcIPGroupID, PstnPrefix_DestHostPrefix, PstnPrefix_SrcHostPrefix;

PstnPrefix 0 = *, 1, *, *, 1, -1, , ;

[ \PstnPrefix ]

;

;  *** TABLE ProxyIp ***

; 

;

[ ProxyIp ]

FORMAT ProxyIp_Index = ProxyIp_IpAddress, ProxyIp_TransportType, ProxyIp_ProxySetId;

ProxyIp 0 = 192.168.10.6, 0, 0;

[ \ProxyIp ]

;

;  *** TABLE TxDtmfOption ***

; 

;

[ TxDtmfOption ]

FORMAT TxDtmfOption_Index = TxDtmfOption_Type;

TxDtmfOption 0 = 4;

[ \TxDtmfOption ]

;

;  *** TABLE TrunkGroupSettings ***

; 

;

[ TrunkGroupSettings ]

FORMAT TrunkGroupSettings_Index = TrunkGroupSettings_TrunkGroupId, TrunkGroupSettings_ChannelSelectMode, TrunkGroupSettings_RegistrationMode, TrunkGroupSettings_GatewayName, TrunkGroupSettings_ContactUser, TrunkGroupSettings_ServingIPGroup;

TrunkGroupSettings 0 = 1, 1, 0, , , -1;

[ \TrunkGroupSettings ]

;

;  *** TABLE TargetOfChannel ***

; 

;

[ TargetOfChannel ]

FORMAT TargetOfChannel_Index = TargetOfChannel_Destination, TargetOfChannel_Type;

TargetOfChannel 0 = 100, 1;

TargetOfChannel 1 = 100, 1;

TargetOfChannel 2 = 100, 1;

TargetOfChannel 3 = 100, 1;

TargetOfChannel 4 = 100, 1;

TargetOfChannel 5 = 100, 1;

TargetOfChannel 6 = 100, 1;

TargetOfChannel 7 = 100, 1;

[ \TargetOfChannel ]

;

;  *** TABLE ProxySet ***

; 

;

[ ProxySet ]

FORMAT ProxySet_Index = ProxySet_EnableProxyKeepAlive, ProxySet_ProxyKeepAliveTime, ProxySet_ProxyLoadBalancingMethod, ProxySet_IsProxyHotSwap;

ProxySet 0 = 0, 60, 0, 0;

[ \ProxySet ]

Debugging AudioCodes MP-118 FXO

4/3/14: With sipx4.6 using the audiocodes 5.8 firmware worked fine after loading the .ini file from sipx manually.  The 6.x versions of firmware did not work.

---

Enable Hold=>True

The main line is the only phone that can call out.  No matter what we do we get the dial tone but are unable to process an outgoing call.

Hold Format=>SendOnly

same problem

Enable Hold =>False , burn.

burn and reset.

uploaded usa_tones_12.ini

added the ntp server back.

dial mode=>one stage

reset ini file as the usa_tones_12.ini seemed to have wiped out everything.

dtmfvolume -15 =>0

other dtmf volume -11=>0

Enable Continuity Tones =>enable

Silence Detection Method none=>all

deleted usa_tones.dat

Enable Polarity Reversal=>true

On Sun, 2010-04-11 at 03:04 -0500, Josh Patten wrote:> OK I've found what I think is the fix, but let me run it by everyone > here to make sure it won't break anything. >  > In the Audiocodes I disabled PRACK: Protocol Configuration >> Protocol > Definition >> SIP General Parameters >> PRACK Mode = Disable (was: > Supported) >  > Anyone know why PRACK causes issues with forking in 4.0.4 and not > 4.1.7? Will not having PRACK enabled cause issues?Using PRACK may significantly increase the amount of state that the gateway thinks it needs to keep for early dialogs, which would be consistent with the resource errors that were in your logs. To be sure, you'd have to ask Audiocodes. In any event, for what you're doing PRACK offers no added value, so leaving it off is just fine.

--
You received this message because you are subscribed to the Google Groups "sipxcom-users" group.
To unsubscribe from this group and stop receiving emails from it, send an email to sipxcom-user...@googlegroups.com.
To view this discussion visit https://groups.google.com/d/msgid/sipxcom-users/14248540-79ee-445b-8dcb-6aecc4314658n%40googlegroups.com.

[Todd Hodgen]

Personally, I have always downgraded the firmware to older versions supported by sipxcom.  I think 5.8 was what I primarily used.

Sent with my two left twiddling thumbs

---

From: 'North Blue' via sipxcom-users <sipxco...@googlegroups.com>
Sent: Wednesday, June 11, 2025 8:09:51 AM
To: sipxcom-users <sipxco...@googlegroups.com>
Subject: [sipxcom-users] MP118 FXO Config

 

--

[North Blue]

Thank you Gerald, 

Thank you Todd. 

Very much appreciated. I'll downgrade to 5.8 now. 

[Todd Hodgen]

If you do that, then you can add it as a device in sipXcom, configure it, send profile, then go back and download the sipXcom created ini file and upload it to the device.  It will reboot and you will be done.

Sent with my two left twiddling thumbs

---

From: 'North Blue' via sipxcom-users <sipxco...@googlegroups.com>

Sent: Wednesday, June 11, 2025 5:20:18 PM
To: sipxcom-users <sipxco...@googlegroups.com>
Subject: Re: [sipxcom-users] MP118 FXO Config

 

To view this discussion visit https://groups.google.com/d/msgid/sipxcom-users/6b900bb0-646a-4456-a204-8fd6cf8b36f6n%40googlegroups.com.