Google Groups no longer supports new Usenet posts or subscriptions. Historical content remains viewable.
Dismiss
repair microwave ovan
75 views
Skip to first unread message
sen...@hotmail.com
Feb 7, 2015, 7:32:59 PM2/7/15
to
I have a Panasonic NN-GS597M microwave. When using its microwave heating function, it stops after 4 seconds regardless of the setting is H/M/L. In this 4 seconds, there is a slight "tic tic" sound near the a/c rectifier and the large transformer of the inverter (they seat close to each other). I managed to find an inverter board and replaced it, but didn't solve the problem. So it must be something else that cause the problem.
The rectifier board is just simple R, C, varistor and self recovering fuse, which are unlikely to have any problem. For magnetron, I've measured the resistance of the 2 leads. With my DMM at 200ohm it reads 0.3. Each lead is open to the case of the ovan. So I think the magnetron is ok. So what else can I check to resolve the problem. Please help.
NB. http://www.repairfaq.org/sam/micfaq.htm is where I learn the above, in case it can help others.
The rectifier board is just simple R, C, varistor and self recovering fuse, which are unlikely to have any problem. For magnetron, I've measured the resistance of the 2 leads. With my DMM at 200ohm it reads 0.3. Each lead is open to the case of the ovan. So I think the magnetron is ok. So what else can I check to resolve the problem. Please help.
NB. http://www.repairfaq.org/sam/micfaq.htm is where I learn the above, in case it can help others.
sender jones
Feb 7, 2015, 7:48:28 PM2/7/15
to
One more point, during this 4 seconds, the ovan is noisy as usual. But after it failed, it is quiet but the cooling fan is still turning.
c4urs11
Feb 8, 2015, 4:33:47 AM2/8/15
to
On Sat, 07 Feb 2015 16:48:25 -0800, sender jones wrote:
> One more point, during this 4 seconds, the ovan is noisy as usual.
> But after it failed, it is quiet but the cooling fan is still turning.
Can this help, disregarding its fun typos?
> One more point, during this 4 seconds, the ovan is noisy as usual.
> But after it failed, it is quiet but the cooling fan is still turning.
http://ask.metafilter.com/259488/Possessed-mircowave
Cheers!
Samuel M. Goldwasser
Feb 8, 2015, 4:17:07 PM2/8/15
to
sender jones <sen...@hotmail.com> writes:
> One more point, during this 4 seconds, the ovan is noisy as usual. But
> after it failed, it is quiet but the cooling fan is still turning.
There isn't much besides the rectifier, inverter, and magnetron.
> One more point, during this 4 seconds, the ovan is noisy as usual. But
> after it failed, it is quiet but the cooling fan is still turning.
That tick tick might be the inverter trying to power an excessive load -
just a guess.
Magnetrons can fail with voltage applied and test good on a meter.
You can probably find a new/NOS replacement for less than $20 on eBay.
It's worth the risk. :)
--
sam | Sci.Electronics.Repair FAQ: http://www.repairfaq.org/
Repair | Main Table of Contents: http://www.repairfaq.org/REPAIR/
+Lasers | Sam's Laser FAQ: http://www.repairfaq.org/sam/lasersam.htm
| Mirror Sites: http://www.repairfaq.org/REPAIR/F_mirror.html
Important: Anything sent to the email address in the message header above is
ignored unless my full name AND either lasers or electronics is included in the
subject line. Or, you can contact me via the Feedback Form in the FAQs.
sender jones
Mar 23, 2015, 9:31:59 PM3/23/15
to
https://kanbox.com/a/zE7nqe
Are modern domestic microwave ovens still use beryllium oxide in their magnetron insulator. I know beryllium is highly toxic. But will such scratch mark dangerous?
0 new messages