tool for stripping wires without cutting them?
zirc...@yahoo.com
to strip the wires, if its not too expensive. I have a set of plier-
like ones, where you insert the wire into the correct slot, squeeze
the handles, then pull the wire through, shedding the insulation.
But that is only for stripping the ends of wires. I'd like to be able
to strip wires 'inline', without cutting them. Is that what an
automatic stripper does? Like
http://www.radioshack.com/product/index.jsp?productId=2062786
or
http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=42101
Or is there another tool? Thanks.
zirc...@yahoo.com
> http://www.wrcase.com/knives/pocket_knives/
Thats what I used when I put in my last remote starter. It was a lot
of slow, careful work. I was hoping there was a tool that could do
this quickly and without risk of cutting the wire.
Homer J Simpson
<zirc...@yahoo.com> wrote in message
news:1175052958.8...@r56g2000hsd.googlegroups.com...
> I plan to install a remote starter in my car. I'd like to buy a tool
> to strip the wires, if its not too expensive. I have a set of plier-
> like ones, where you insert the wire into the correct slot, squeeze
> the handles, then pull the wire through, shedding the insulation.
>
> But that is only for stripping the ends of wires. I'd like to be able
> to strip wires 'inline', without cutting them. Is that what an
> automatic stripper does? Like
You can buy those in dollar stores.
> Or is there another tool? Thanks.
Most of us use a pocket knife - carefully, so as to not nick the wire.
mark krawczuk
?? buy a cigarette lighter, soften/melt the plastic and QUICKLY pul the
insulastion off with ya fingers.
mark k
<zirc...@yahoo.com> wrote in message
news:1175052958.8...@r56g2000hsd.googlegroups.com...
Anthony Fremont
Those strippers are for stripping the end only. Their specialty is that
they "adjust" to the size of the wire automatically. This means they only
remove 10% of the strands along with the insulation. ;-)
Seriously, you should use a better connector instead. You don't want to
strip an inch of insulation off, you just want to displace enough insulation
to make a connection. Something like these:
http://www3.3m.com/catalog/us/en001/utilities_telecom/electrical_contractors/node_GSPV65GVLXbe/root_GST1T4S9TCgv/vroot_GSBCDFDZ1Zge/gvel_RZZJLFZNT6gl/theme_us_electricalcontractors_3_0/command_AbcPageHandler/output_html
Try to find some that have a moisture resistant grease inside. This will
not only keep water out, but the air too.
Michael Kennedy
I use linemans plyers / dikes, but lots of people can't strip wire with
them.. They are my favorite tool for stripping wire.
Dave Plowman (News)
<zirc...@yahoo.com> wrote:
> I plan to install a remote starter in my car. I'd like to buy a tool
> to strip the wires, if its not too expensive. I have a set of plier-
> like ones, where you insert the wire into the correct slot, squeeze
> the handles, then pull the wire through, shedding the insulation.
> But that is only for stripping the ends of wires. I'd like to be able
> to strip wires 'inline', without cutting them. Is that what an
> automatic stripper does? Like
> http://www.radioshack.com/product/index.
> or
> http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=42101
> Or is there another tool? Thanks.
Of these two the RS one is ideal for this purpose - provided you use the
correct size for the cable, and the sizes provided by the jaws cover the
cables in use.
I've got just about every cable stripper known to man and although the
automatic types sound like a good idea they simply don't match up to this
type for stripping with no chance of conductor damage - provided as I say
you use the correct 'notch' out of the four provided and make sure it's
aligned on the cable. If you're sloppy about this it makes a good cable
cutter. ;-) The snag is it needs more space to work than some other types.
This type is also of use as again won't damage the conductor but has to be
manually adjusted. Couldn't find it on the RS site, but most electricians
use them.
http://www.tlc-direct.co.uk/Products/VA237.html
--
*Why is a boxing ring square?
Dave Plowman da...@davenoise.co.uk London SW
To e-mail, change noise into sound.
Arfa Daily
"Anthony Fremont" <spam...@nowhere.com> wrote in message
news:130k06i...@news.supernews.com...
That's exactly the item that I was going to suggest as well. They are made
for the job of in-line splicing, and do it very well.
Arfa
James Sweet
> In article <1175052958.8...@r56g2000hsd.googlegroups.com>,
> <zirc...@yahoo.com> wrote:
>
>>I plan to install a remote starter in my car. I'd like to buy a tool
>>to strip the wires, if its not too expensive. I have a set of plier-
>>like ones, where you insert the wire into the correct slot, squeeze
>>the handles, then pull the wire through, shedding the insulation.
>
>
>>But that is only for stripping the ends of wires. I'd like to be able
>>to strip wires 'inline', without cutting them. Is that what an
>>automatic stripper does? Like
>>http://www.radioshack.com/product/index.
>>or
>>http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=42101
>
>
>>Or is there another tool? Thanks.
>
>
>
I use a T-stripper, I love it.
http://www.twacomm.com/catalog/model_45-120CS.htm
Dave Plowman (News)
Arfa Daily <arfa....@ntlworld.com> wrote:
> That's exactly the item that I was going to suggest as well. They are
> made for the job of in-line splicing, and do it very well.
And look like the bodge they are. ;-) You'll not find them used on a
maker's harness.
--
*I don't have a solution, but I admire your problem. *
Anthony Fremont
> In article <dBpOh.8464$F82....@newsfe4-win.ntli.net>,
> Arfa Daily <arfa....@ntlworld.com> wrote:
>> That's exactly the item that I was going to suggest as well. They are
>> made for the job of in-line splicing, and do it very well.
>
> And look like the bodge they are. ;-) You'll not find them used on a
> maker's harness.
Do you think that stripping an inch of insulation in the middle of a run is
a better way to go? If so, you'll not be doing any wiring on my car. ;-)
Short of soldering, I can't think of anything more reliable than IDC type
crimp-ons. They're used all over the place in critcal applications. e.g.
computer data cables, network and telephone industry etc. Auto makers use
plenty of crimp-on pins too. :-)
ampdoc
"Arfa Daily" <arfa....@ntlworld.com> wrote in message
news:dBpOh.8464$F82....@newsfe4-win.ntli.net...
90% of professional alarm installers use the T-Tap 3M connectors. They have
a great track record and work well, and are used because of the speed in
which they can be put in, as well as the fact you don't want to drop a hot
soldering iron in a brand new corvette seat :-). If you use some 3M super 33
tape and wrap the harness for the alarm, and wrap your connections properly,
when you finish it looks enough like the car harness that a thief is hard
pressed to find the alarm wiring :-)
Jammy
(Got stuck doing installs as well as repairs when I started in electronics)
Dave Plowman (News)
But they're not a crimp. Proper crimped connections are fine.
--
*I'm out of my mind, but feel free to leave a message.
Dave Plowman (News)
ampdoc <amp...@hotmail.com> wrote:
> > That's exactly the item that I was going to suggest as well. They are
> > made for the job of in-line splicing, and do it very well.
> 90% of professional alarm installers use the T-Tap 3M connectors.
And 90% of aftermarket alarms are a problem within a few years. ;-)
--
*I'm not being rude. You're just insignificant
Jamie
There you go, cheapest cutters and the most handy..
I have auto strippers and never use them. I can strip must faster
with those simple ones.
--
"I'm never wrong, once i thought i was, but was mistaken"
Real Programmers Do things like this.
http://webpages.charter.net/jamie_5
Franc Zabkar
keyboard and composed:
I use several mentioned in this thread, including yours. I also use a
"T-Rex" for ribbon cable and such like:
http://www.sicom.co.nz//site/images/42904.jpg
- Franc Zabkar
--
Please remove one 'i' from my address when replying by email.
Franc Zabkar
<fza...@iinternode.on.net> put finger to keyboard and composed:
Sorry, I just realised that you wanted to strip *without* cutting.
David Brodbeck
> And 90% of aftermarket alarms are a problem within a few years. ;-)
90% of aftermarket alarms are apparently installed with the noise- and
vibration-detectors turned all the way up, presumably so the person
buying them will feel like they got something for their money. The
result is continual false alarms.
I don't know why anyone buys an alarm system anymore. After years of
getting a 3 am alarm serenade I have to say my first reaction upon
hearing a car alarm is *not* that someone must be stealing the car.
Someone needs to invent an EMP gun that can take these little
noisemakers out at fifty paces. ;)
Ross Herbert
There are a number of tools for stripping cable sheath longtitudinally
eg. Knipex
http://www.justoffbase.co.uk/Cable-Sheath-Stripper-51735-Draper-16-30-135-SB?sc=9&category=1051
but these are only for cables of around 6mm diam minimal. In order to
strip individual conductor sheathing (insulation) for smaller gauges
this is a rather specialised function for such purposes as stripping
thermocouple wires. This company sells this type of stripping tool but
they would be very expensive and probably only viable for mass
production. You also need a different stripper die for each wire
gauge.
http://www.ariindustries.com/accessories/sheath_stripping_tool.php3
zirc...@yahoo.com
http://rsk.imageg.net/graphics/product_images/pRS1C-2160702w345.jpg
For $12.99. It was a piece of junk, it felt like it was going to fall
apart. I didn't even test it out, I just took it back.
Then I bought a different brand from Menards (home improvement store),
where you don't have to choose what size wire you are stripping, for
$15
And one of these (the kind where you must select the right hole for
your size of wire) for $25:
http://www.homedepot.com/cmc_upload/HDUS/EN_US/asset/images/eplus/783250452620_4.jpg
I tried them both. The $25 set (the only one made in the USA) works
great. I'll be keeping that one.
It does strip wire in the middle, but not perfectly. But it will be
much easier than manually trying to cut without damaging any strands.
I'll still have to make a laterall cut manually.
Thanks for all the input.
Dave Plowman (News)
<zirc...@yahoo.com> wrote:
> I ended up getting this one from Radio Shack:
> http://rsk.imageg.net/graphics/product_images/pRS1C-2160702w345.jpg
> For $12.99. It was a piece of junk, it felt like it was going to fall
> apart. I didn't even test it out, I just took it back.
I have one of similar design - not of course from Radio Shack - and it
cost a deal more than the one they show. It's the best wire stripper I
have and I have many. It's also had a lot of use and still works properly
on the original jaws which are available as spares.
I can't of course comment on the RS one, but not even trying something
after buying seems strange.
--
*If they arrest the Energizer Bunny, would they charge it with battery? *
zirc...@yahoo.com
> I can't of course comment on the RS one, but not even trying something
> after buying seems strange.
I did try it, by working the tool in my hand many times, that was
enough. The operation of the left and right jaws weren't right,
sometimes when you let the tool close the blades wouldn't be open so
you couldn't put the wires in. The handles didn't move smoothly, they
wanted to wobble all over instead of moving in an arc. Sometimes it
would get stuck open.
As soon as I opened the package of the US made one, I could tell just
by the feel of it that it was a much much better tool.
David Brodbeck
> In article <1175221988....@p15g2000hsd.googlegroups.com>,
> <zirc...@yahoo.com> wrote:
>> I ended up getting this one from Radio Shack:
>> http://rsk.imageg.net/graphics/product_images/pRS1C-2160702w345.jpg
>> For $12.99. It was a piece of junk, it felt like it was going to fall
>> apart. I didn't even test it out, I just took it back.
>
> I have one of similar design - not of course from Radio Shack - and it
> cost a deal more than the one they show. It's the best wire stripper I
> have and I have many. It's also had a lot of use and still works properly
> on the original jaws which are available as spares.
When made correctly that type of tool can work very well. I have one
made specifically for RG-59U coax that I use when installing security
cameras. It's very quick and reliable. But it's a fairly heavy-duty,
well-made item, which means it probably didn't come from Radio Shack. ;)