Google Groups no longer supports new Usenet posts or subscriptions. Historical content remains viewable.
Dismiss
Sumvision SV 1000 recording DVD
6 views
Skip to first unread message
N_Cook
Jan 2, 2014, 5:04:17 AM1/2/14
to
Burnt and burst SMPS supervisor on this otherwise no-name and little
chance Chinese thing. As laser and motor/s in the DVD deck and heatsink
bonded to a video chip a reasonable power draw.
But the SMPS IC , in a conventional 8 pin DIP package also contains the
Tx driver transistor. So air gap under the IC and reverse side of pcb
enlarged pad of pcb-copper as some sort of vain attempt at heatsink.
Thermal connection to this is via just pins 4 and 5 combined in normal
soldering , connected to the Tx. There is a hole through the pcb as
though for some sort of clip to go perhaps top and bottom of the IC and
bolted through to this under pad but no sign of anything having been
fitted there, no deformation of the tinning over the pad around the
hole. Turning over the unit and shaking over paper meant the blasted
away top part , mainly, of the IC emerged but no clip at all.
Is it possible to have combined supervisor and driver transistor in an
8pin DIP package with no heatsink tab provision? or are there combined
SMPS TX with internal driver transistor buried in the base?
Also ps supply provision marked on pcb ac 85V - 250V
IC logi i in a reversed D
marked in 3 lines ICE 2?26 maybe more numbers, ? maybe a 4
logo then 0 and more
XK4.. probably more numbers
probable pinning
p1 0.1uF to 0V
p2 to optocoupler
p3 over current sense
p4-p5 to Tx low side
p6 n/c
p7 supply <25V
p8 0V
chance Chinese thing. As laser and motor/s in the DVD deck and heatsink
bonded to a video chip a reasonable power draw.
But the SMPS IC , in a conventional 8 pin DIP package also contains the
Tx driver transistor. So air gap under the IC and reverse side of pcb
enlarged pad of pcb-copper as some sort of vain attempt at heatsink.
Thermal connection to this is via just pins 4 and 5 combined in normal
soldering , connected to the Tx. There is a hole through the pcb as
though for some sort of clip to go perhaps top and bottom of the IC and
bolted through to this under pad but no sign of anything having been
fitted there, no deformation of the tinning over the pad around the
hole. Turning over the unit and shaking over paper meant the blasted
away top part , mainly, of the IC emerged but no clip at all.
Is it possible to have combined supervisor and driver transistor in an
8pin DIP package with no heatsink tab provision? or are there combined
SMPS TX with internal driver transistor buried in the base?
Also ps supply provision marked on pcb ac 85V - 250V
IC logi i in a reversed D
marked in 3 lines ICE 2?26 maybe more numbers, ? maybe a 4
logo then 0 and more
XK4.. probably more numbers
probable pinning
p1 0.1uF to 0V
p2 to optocoupler
p3 over current sense
p4-p5 to Tx low side
p6 n/c
p7 supply <25V
p8 0V
Arfa Daily
Jan 5, 2014, 5:24:09 PM1/5/14
to
"N_Cook" <div...@tcp.co.uk> wrote in message
news:la3dir$5hi$1...@dont-email.me...
number are quite common. Such ICs are often coupled directly to a power FET
switching element, but are just as commonly connected directly to a small
SMPS Tx, particularly when it is a standby supply. I have always been amazed
that these chips can stand the better part of 400 volts across their
internal FET, and that it can supply enough current to drive the Tx
directly. I guess the thermal issues are dictated by how good the RDSon of
the internal device is. The closer it is to zero ohms, the lower the
dissipation, and some these days are pretty damn close to zero for all
practical purposes.
Arfa
N_Cook
Jan 6, 2014, 3:32:16 AM1/6/14
to
look right. For something like a set-top box with no motors or laser and
a graphics processor that does not require a heatsink, I could see it
was possible
N_Cook
Jan 6, 2014, 3:49:16 AM1/6/14
to
On 05/01/2014 22:24, Arfa Daily wrote:
>
>
>
>
ICE2 starting it seems its like a
ICE2A265 with a different logo, same pinning on p4/5/6 at least
large datasheet , will have to read it when I get some time
N_Cook
Jan 6, 2014, 4:24:19 AM1/6/14
to
Perhaps another piece of hitech saved from the dumpster
i in reverse D ,logo on
http://www.aufzu.de/semi/siemens.html
as infineon, perhaps older or IC only logo (don't know German) and the
other pinnings agree with Infineon datasheet. Will get a few from RS ,
but will add an underpad-soldered copper 20mm pcb fuse clip and white
goo around the IC, assuming it will still oscillate etc
i in reverse D ,logo on
http://www.aufzu.de/semi/siemens.html
as infineon, perhaps older or IC only logo (don't know German) and the
other pinnings agree with Infineon datasheet. Will get a few from RS ,
but will add an underpad-soldered copper 20mm pcb fuse clip and white
goo around the IC, assuming it will still oscillate etc
0 new messages