SCALE Software Coordinator
This topic has been migrated from the SCALE 6 notebook.
Date: Wed Nov 30 13:16:01 2011
The text below is out of the dos window running TSUNAMI-3D. It went through the forward and adjoint calculations, built the sensitivity data files with SAMS, then crashed with K-mart. It looks like it found the file, but didn't like what it found. Input and output files are attached.
When run from the batch window in Gee-Whiz, the following was at the end of the output file.
Error in opnfil, old file -restart.keno_calculated- does not exist Execution will terminate
stop code 201
t3_pmf_010
generation average avg k-eff elapsed time
generation k-effective k-effective deviation minutes
646 1.28661E+00 9.88963E-01 2.13861E-02 2.13467E+00
647 5.77652E-01 9.88136E-01 2.13590E-02 2.13650E+00
648 1.05127E+00 9.88262E-01 2.13164E-02 2.13883E+00
649 8.09517E-01 9.87904E-01 2.12766E-02 2.14067E+00
650 7.18505E-01 9.87365E-01 2.12408E-02 2.14250E+00
t3_pmf_010
****** final results table ******
best estimate system k-eff 0.987 + or - 0.021
Energy of average lethargy of Fission (eV) 2.79173E-03 + or - 5.06238E-06
k-effective fails the chi**2 test for normality at the 95 % level, but satisfies it at the 99 % level
------------------------------
Starting SAMS Calculation
------------------------------
Now executing sams5
Reading Adjoint Data
Reading Forward Data
Computing Explicit Sensitivities for Nuclide 1031000 (1 of 6)
Computing Explicit Sensitivities for Nuclide 2092235 (2 of 6)
Computing Explicit Sensitivities for Nuclide 2092238 (3 of 6)
Computing Explicit Sensitivities for Nuclide 1094239 (4 of 6)
Computing Explicit Sensitivities for Nuclide 1094240 (5 of 6)
Computing Explicit Sensitivities for Nuclide 1094241 (6 of 6)
Computing Implicit Sensitivities from BONAMIST
Computing Uncertainty Data
-----------------------------------
SAMS execution complete
Elapsed time: 0.02167 minutes
-----------------------------------
Now executing kmart5
forrtl: severe (24): end-of-file during read, unit 35, file C:\scale6
\tmpdir\res
tart.keno_calculated
Image PC Routine Line Source
kmart5.exe 0051572A Unknown Unknown Unknown
kmart5.exe 00512FE5 Unknown Unknown Unknown
kmart5.exe 004C2718 Unknown Unknown Unknown
kmart5.exe 004C2251 Unknown Unknown Unknown
kmart5.exe 0049607C Unknown Unknown Unknown
kmart5.exe 00419E72 _CALCULATED_DATA_ 138 calculated_data_M.f90
kmart5.exe 00409C47 _GET_FLUXES._READ 197 get_fluxes.f90
kmart5.exe 00408889 _GET_FLUXES 128 get_fluxes.f90
kmart5.exe 0040102A _MAIN__ 10 kmart5.f90
kmart5.exe 0051BC5D Unknown Unknown Unknown
kmart5.exe 004FE612 Unknown Unknown Unknown
kernel32.dll 7C817077 Unknown Unknown Unknown
forrtl: severe (157): Program Exception - access violation
Image PC Routine Line Source
ntdll.dll 7C911689 Unknown Unknown Unknown
ntdll.dll 7C91084C Unknown Unknown Unknown
kmart5.exe 004FF222 Unknown Unknown Unknown
kmart5.exe 00491D9B Unknown Unknown Unknown
kmart5.exe 004C2708 Unknown Unknown Unknown
kmart5.exe 004C2251 Unknown Unknown Unknown
kmart5.exe 0049607C Unknown Unknown Unknown
kmart5.exe 00419E72 _CALCULATED_DATA_ 138 calculated_data_M.f90
kmart5.exe 00409C47 _GET_FLUXES._READ 197 get_fluxes.f90
kmart5.exe 00408889 _GET_FLUXES 128 get_fluxes.f90
kmart5.exe 0040102A _MAIN__ 10 kmart5.f90
kmart5.exe 0051BC5D Unknown Unknown Unknown
kmart5.exe 004FE612 Unknown Unknown Unknown
kernel32.dll 7C817077 Unknown Unknown Unknown
forrtl: severe (157): Program Exception - access violation
Scale6 job "t3_pmf_010" is finished.
Output is stored in "t3_pmf_010.out."
C:\11calcs>
C:\11calcs>
Jerry Hicks
SCALE Software Coordinator
Hi Jerry,
Unfortunately, you’re run into a limitation in SCALE 6.0. The flux data file written by TSUNAMI-3D has a different name than KMART expects. We have corrected this issue for SCALE 6.1.
For SCALE 6.0, there are two solutions. The first is to repeat your KENO calculation using CSAS instead of TSUNAMI-3D. CSAS will allow KENO to generate the properly named KMART file. In this case, you can accelerate the KENO calculation by removing TSUNAMI parameters such as msh, pnm, and nqd.
The second is to edit the input file outside of GeeWiz to add the
following shell command between the end of the TSUNAMI-3D input and the beginning of the KMART input and run outside of GeeWiz (e.g. with the Run SCALE 6 drag-and-drop icon).
=shell
move restart.forward.keno_calculated restart.keno_calculated
end
On Linux/Mac, the command is
=shell
mv restart.forward.keno_calculated restart.keno_calculated
end
Please see input file below for an example and let me know if you have any problems.
--------input file: tsunami-3d_k5-1-kmart.inp--------
'Input generated by GeeWiz SCALE 6.0.10.30 Compiled on October 30, 2009
=tsunami-3d-k5
tsunami-3d sample 1
v6-238
read composition
u-235 1 0 0.00013303 300 end
u-238 1 0 0.006437 300 end
h 1 0 0.039097 300 end
c 1 0 0.018797 300 end
f 1 0 0.02628 300 end
end composition
read parameter
gen=200
npg=3000
htm=yes
sig=0.001
cfx=yes
ask=150
asg=0.005
end parameter
read geometry
global unit 1
com='global unit 1'
sphere 1 1 5
sphere 1 1 10
sphere 1 1 15
sphere 1 1 20
sphere 1 1 25
sphere 1 1 30
sphere 1 1 35
sphere 1 1 37
sphere 1 1 38.5
end geometry
end data
read sams
prtgeom
prtimp
end sams
end
=shell
move restart.forward.keno_calculated restart.keno_calculated
end
=kmart
read initial
kunit=35
xunit=4
keno3d 40 tsunami-3d_k5-1-kmart.kmt
end initial
read activity
92235 1
end activity
end
-----------end of input file------------------------
Best Regards,
Brad Rearden
SCALE Software Coordinator
Dennis Mennerdahl