Comtrend Firmware

[Barb Frison]

It's very uncommon to find custom firmware for ADSL routers. I suggest you look into your manual to see if you can set it in bridge mode, and you get yourself a router from this list _available_864 to flash with OpenWrt.

Devices with Broadcom WiFi chipsets have limited OpenWrt supportability (due to limited FLOSS driver availability for Broadcom chips). Consider this when choosing a device to buy, or when deciding to flash OpenWrt on your device because it is listed as supported.See Broadcom WiFi for details.

DSL will not work at all on devices with BCM63xx DSL chipset (due to unavailability of FLOSS driver for Broadcom chips). Consider this when choosing a device to buy, or when deciding to flash OpenWrt on your device because it is listed as supported.

See Broadcom DSL, Unsupported: DSL modem and Broadcom BCM63xx for details.

No physical EEPROM at the board, nor partition reserverd for this data at the flash chip. In theory, in the original firmware, the EEPROM is taken from the file /etc/wlan/bcm43225_map.bin, although some bytes differ when comparing with wlctl dumps.

[ 0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sun Sep 9 20:22:25 CEST 2012[ 0.000000] Detected Broadcom 0x6328 CPU revision 10b0[ 0.000000] CPU frequency is 320 MHz[ 0.000000] 64MB of RAM installed[ 0.000000] registering 32 GPIOs[ 0.000000] gpiochip_add: registered GPIOs 0 to 31 on device: bcm63xx-gpio[ 0.000000] board_bcm963xx: Boot address 0xb8000000[ 0.000000] board_bcm963xx: CFE version: 1.0.37-106.5[ 0.000000] bootconsole [early0] enabled[ 0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350)[ 0.000000] board_bcm963xx: board name: 96328A-1241N[ 0.000000] Determined physical RAM map:[ 0.000000] memory: 04000000 @ 00000000 (usable)[ 0.000000] Initrd not found or empty - disabling initrd[ 0.000000] Zone PFN ranges:[ 0.000000] Normal 0x00000000 -> 0x00004000[ 0.000000] Movable zone start PFN for each node[ 0.000000] Early memory PFN ranges[ 0.000000] 0: 0x00000000 -> 0x00004000[ 0.000000] On node 0 totalpages: 16384[ 0.000000] free_area_init_node: node 0, pgdat 802acea0, node_mem_map 81000000[ 0.000000] Normal zone: 128 pages used for memmap[ 0.000000] Normal zone: 0 pages reserved[ 0.000000] Normal zone: 16256 pages, LIFO batch:3[ 0.000000] Reserving 0MB of memory at 0MB for crashkernel[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768[ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.[ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes[ 0.000000] Memory: 61808k/65536k available (2262k kernel code, 3728k reserved, 415k data, 204k init, 0k highmem)[ 0.000000] NR_IRQS:128[ 0.000000] Calibrating delay loop... 318.46 BogoMIPS (lpj=636928)[ 0.036000] pid_max: default: 32768 minimum: 301[ 0.040000] Mount-cache hash table entries: 512[ 0.048000] NET: Registered protocol family 16[ 0.276000] registering PCI controller with io_map_base unset[ 0.288000] bio: create slab at 0[ 0.292000] PCI host bridge to bus 0000:00[ 0.296000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x11efffff][ 0.300000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0][ 0.304000] pci 0000:00:00.0: [14e4:6328] type 1 class 0x000604[ 0.304000] pci 0000:00:00.0: PME# supported from D0 D3hot[ 0.304000] pci 0000:01:00.0: [14e4:a8d8] type 0 class 0x000280[ 0.304000] pci 0000:01:00.0: reg 10: [mem 0x00000000-0x00003fff 64bit][ 0.304000] pci 0000:01:00.0: supports D1 D2[ 0.304000] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff][ 0.308000] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit][ 0.312000] pci 0000:00:00.0: PCI bridge to [bus 01-01][ 0.316000] pci 0000:00:00.0: bridge window [mem 0x10f00000-0x10ffffff][ 0.320000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)[ 0.324000] Switching to clocksource MIPS[ 0.332000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)[ 0.340000] bcma: bus0: Found chip with id 0xA8D9, rev 0x01 and package 0x08[ 0.344000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0)[ 0.356000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0)[ 0.364000] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0)[ 0.372000] bcma: bus0: Found rev 6 PMU (capabilities 0x108C2606)[ 0.372000] bcma: bus0: PMU resource config unknown or not needed for device 0xA8D9[ 0.372000] bcma: bus0: Workarounds unknown or not needed for device 0xA8D9[ 0.404000] bcma: bus0: SPROM offset 0x800[ 0.444000] bcma: Reading SPROM failed. Trying fallback SPROM...[ 0.444000] bcm63xx_sprom_bcma: filled BCMA SPROM for chip id 0xa8d9[ 0.448000] bcma: bus0: Using SPROM revision 8 provided by platform.[ 0.448000] bcma: bus0: Bus registered[ 0.452000] NET: Registered protocol family 2[ 0.460000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)[ 0.468000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)[ 0.472000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)[ 0.480000] TCP: Hash tables configured (established 2048 bind 2048)[ 0.488000] TCP reno registered[ 0.492000] UDP hash table entries: 256 (order: 0, 4096 bytes)[ 0.496000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)[ 0.504000] NET: Registered protocol family 1[ 0.508000] PCI: CLS 0 bytes, default 16[ 0.512000] audit: initializing netlink socket (disabled)[ 0.516000] type=2000 audit(0.516:1): initialized[ 0.524000] squashfs: version 4.0 (2009/01/31) Phillip Lougher[ 0.528000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.[ 0.540000] msgmni has been set to 120[ 0.544000] io scheduler noop registered[ 0.548000] io scheduler deadline registered (default)[ 0.556000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm63xx_uart[ 0.564000] console [ttyS0] enabled, bootconsole disabled[ 0.580000] m25p80 spi0.0: found mx25l12805d, expected m25p80[ 0.588000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)[ 0.592000] bcm63xxpart: CFE boot tag found with version 6 and board type 96328A-1241N[ 0.600000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000[ 0.608000] bcm63xxpart: Partition 1 is kernel offset 10100 and length eff00[ 0.612000] bcm63xxpart: Partition 2 is rootfs offset 100000 and length ef0000[ 0.620000] bcm63xxpart: Partition 3 is nvram offset ff0000 and length 10000[ 0.628000] bcm63xxpart: Partition 4 is linux offset 10000 and length fe0000[ 0.636000] bcm63xxpart: Spare partition is offset 340004 and length cafffc[ 0.644000] 5 bcm63xxpart partitions found on MTD device spi0.0[ 0.648000] Creating 5 MTD partitions on "spi0.0":[ 0.656000] 0x000000000000-0x000000010000 : "CFE"[ 0.660000] 0x000000010100-0x000000100000 : "kernel"[ 0.668000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only[ 0.684000] 0x000000100000-0x000000ff0000 : "rootfs"[ 0.692000] mtd: partition "rootfs" set to be root filesystem[ 0.696000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=CB0000 [ 0.704000] 0x000000340000-0x000000ff0000 : "rootfs_data"[ 0.712000] 0x000000ff0000-0x000001000000 : "nvram"[ 0.720000] 0x000000010000-0x000000ff0000 : "linux"[ 0.764000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec[ 0.772000] TCP cubic registered[ 0.776000] NET: Registered protocol family 17[ 0.780000] 8021q: 802.1Q VLAN Support v1.8[ 0.792000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.[ 0.804000] Freeing unused kernel memory: 204k freed[ 3.148000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 4, 100Mbps, full-duplex[ 3.384000] roboswitch: Probing device eth0: [ 3.388000] bcm63xx_enet: could not find a used port with phy_id 0, assuming phy is external[ 3.400000] No Robo switch in managed mode found, phy_id = 0xffffffff[ 3.404000] roboswitch: Probing device eth1: No such device[ 3.412000] roboswitch: Probing device eth2: No such device[ 3.416000] roboswitch: Probing device eth3: No such device[ 5.940000] Button Hotplug driver version 0.4.1[ 12.632000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993[ 12.640000] Backport based on wireless-testing.git master-2012-09-07[ 12.648000] compat.git: wireless-testing.git[ 12.708000] cfg80211: Calling CRDA to update world regulatory domain[ 12.712000] cfg80211: World regulatory domain updated:[ 12.720000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)[ 12.728000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)[ 12.736000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)[ 12.744000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)[ 12.752000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)[ 12.760000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)[ 13.152000] NET: Registered protocol family 10[ 13.596000] SCSI subsystem initialized[ 13.644000] There is already a switch registered on the device 'eth0'[ 13.652000] roboswitch: Probing device eth1: No such device[ 13.656000] roboswitch: Probing device eth2: No such device[ 13.664000] roboswitch: Probing device eth3: No such device[ 13.940000] usbcore: registered new interface driver usbfs[ 13.948000] usbcore: registered new interface driver hub[ 13.956000] usbcore: registered new device driver usb[ 15.188000] NTFS driver 2.1.30 [Flags: R/O MODULE].[ 15.836000] PPP generic driver version 2.4.2[ 16.268000] brcmsmac bcma0:0: mfg 4bf core 812 rev 23 class 0 irq 31[ 16.616000] bcma: bus0: Switched to core: 0x812[ 16.620000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'[ 16.776000] ip_tables: (C) 2000-2006 Netfilter Core Team[ 17.120000] NET: Registered protocol family 24[ 17.456000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver[ 17.568000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller[ 17.572000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1[ 17.604000] bcm63xx_ehci bcm63xx_ehci.0: irq 50, io mem 0xb0002500[ 17.620000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored[ 17.628000] hub 1-0:1.0: USB hub found[ 17.632000] hub 1-0:1.0: 1 port detected[ 17.796000] nf_conntrack version 0.5.0 (968 buckets, 3872 max)[ 18.592000] ip6_tables: (C) 2000-2006 Netfilter Core Team[ 18.904000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver[ 19.016000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller[ 19.020000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2[ 19.028000] bcm63xx_ohci bcm63xx_ohci.0: irq 49, io mem 0xb0002600[ 19.096000] hub 2-0:1.0: USB hub found[ 19.100000] hub 2-0:1.0: 1 port detected[ 19.288000] Initializing USB Mass Storage driver...[ 19.292000] usbcore: registered new interface driver usb-storage[ 19.300000] USB Mass Storage support registered.[ 19.464000] usbcore: registered new interface driver ums-alauda[ 19.492000] usbcore: registered new interface driver ums-cypress[ 19.524000] usbcore: registered new interface driver ums-datafab[ 19.552000] usbcore: registered new interface driver ums-freecom[ 19.584000] usbcore: registered new interface driver ums-isd200[ 19.612000] usbcore: registered new interface driver ums-jumpshot[ 19.640000] usbcore: registered new interface driver ums-karma[ 19.672000] usbcore: registered new interface driver ums-sddr09[ 19.700000] usbcore: registered new interface driver ums-sddr55[ 19.732000] usbcore: registered new interface driver ums-usbat[ 24.320000] device eth0 entered promiscuous mode[ 24.324000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 4, 100Mbps, full-duplex[ 24.336000] br-lan: port 1(eth0) entered forwarding state[ 24.340000] br-lan: port 1(eth0) entered forwarding state[ 26.344000] br-lan: port 1(eth0) entered forwarding state[ 42.920000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0[ 42.928000] jffs2_build_filesystem(): unlocking the mtd device... done.[ 42.932000] jffs2_build_filesystem(): erasing all blocks after the end marker...

3a8082e126