[Aix Eeh Temporary Error For Adapter
Boone Southern
Put the following lines in the file in order to ensure the your DNS changes do not get blown away.(This will replace everything that might exist in wsl.conf. You can also use editor here.)
I have the same problem. It also seems to be realted to VPN.I found out, that it only fails the DNS lookup when I first connect the VPN before starting WSL-Ubuntu after System-Reboot. First starting WSL-Ubuntu and afterwards connecting the VPN seems to work.
I had the same error. Pinging IP addresses worked, but no DNS resolution. Outside of WSL everything was fine. The problem was caused by OpenVPN for me, when I disconnected from my workplace's VPN, the error was gone.
I've had this issue random on multiple machines, old / new / W10 / W11. In my case if I turn off the Windows Defender Firewall -> DNS resolution works fine from WSL.Turning it back on and logging packet drops shows the issue at the public network profile:
I fixed it by setting an inbound firewall rule for the WSL network adapter - run this in Powershell:
New-NetFirewallRule -DisplayName "WSL allow in" -Direction Inbound -InterfaceAlias "vEthernet (WSL)" -Action Allow
I just ran into this issue as well, which is documented on this thread [ ]. One of the comments had the answer for me, which was to put generateResolvConf = true. Not sure why doing the opposite of the original suggestion is the one solution that finally worked, but there you go.
If you use VPN setup on windows, you may want to use dnsTunneling.For that you should use .wslconfig(according to [1]).The .wslconfig file can be edited from windows, open File explorer, enter in the search bar %USERPROFILE%. In the folder opened, create file .wslconfig .Open it with the editor of choice and add:
The Service Bus (SB-Messaging) adapter receive port might sometimes not recover from temporary receive failures that are caused by poor network conditions or a loss of connectivity with Azure Service Bus. In these situations, the host instance has to be restarted to start receiving messages again. Additionally, you receive the following error message:
Alvin Gerholdt, try this " The battery failing is the most likely culprit but you should check to see if there are any problems with either the notebook or Ac adapter before rushing out and replacing the battery.
I would start by checking the bios, start the system tapping F2 to enter the bios, you can also tap F12 and choose bios from the menu. Once in the bios look for the option for AC adapter warnings, if they are disabled enable them and save changes. If there is a problem with the adapter you should start getting errors about the adapter.
If the Adapter seems alright, disconnect the battery from the system and power down the notebook. Wait an hour or so and then replace the battery and restart the system and see if you continue to get the message. If you can run the notebook on battery only allow the battery to fully discharge and then charge it again and see if the problem returns." from here. First instinct is, bad battery. Hope this helps, good luck.
2020 note: As someone who is used to working on more Dell equipment then Lenovo because it's so common here it's easier to get parts for them/parts systems for major repairs like if I need a battery and cannot wait, temp failures are a early warning towards a permanent failure. I don't know how many times it needs to happen, but knowing how paranoid Dell is it's probably low before they throw the permanent failure flag. I've already tripped it once so far.
I wouldn't trust a pack that starts having this problem, or I'd keep a spare with that laptop. It usually begins to be an issue once the packs wain in capacity - my E6440's 29-32% health pack did it. Consider it an early warning it's almost at the end of it's life; not a potential connection fault. On others like some of the flat cell Dell batteries, it's a possible flag for future expansion problems where you need to buy a new battery.
This was happening on my Dell P57G laptop with 11.1v battery. I checked several things and saw that the power supply was producing voltage. The computer when powered on would show the battery disabled and the adapter message was showing a problem as well. Something like not recognized and adjusting for the power needed to run laptop. I then noticed the plug was not inserting properly. Upon closer inspection, the center pin was bent to the side. The laptop would run like this when plugged in, but would not charger the battery. I unplugged and let the power run out of the power supply completely and then used a tiny Philips head screwdriver to bend the center pin back into position. The Philips head allowed me to have a groove to sort of grab the pin and push it gently without slipping off. Sure enough, plugged the power cord back into laptop. It seated like new and the battery charging light came on. Booted up and no more messages about battery being temporarily disabled or the adapter not being recognized.
Dell 7548 bought a new battery and same thing worked fine for a while and then now Everytime it shows the disabled charging. Going to try unplugging and draining battery all the way otherwise will have to fork up for a new battery
When I'm working from home I switch on my PC which is already connected to an ethernet cable: GlobalProtect connects almost immediately (usually to Europe Primary) and I'm able to access my company network drives, folders and remote desktops. However every operation is very slow: network folders take a lot of time to open on explorer, when I launch a RDP connection it takes a lot of time to log onto the the virtual machine and, above all, when I need to connect to oracle databases through ODBC it takes a lot of time to resolve such connections.
If I disconnect the ethernet cable, activate the WiFi connection (from same Router and same ISP) and wait for GlobalProtect to reconnect then everything start to work as expected at a much faster speed: network drives open with a blink of an eye, ODBC Connections are resolved immediately and virtual machines are launched istantly.
Infat now the Ipconfig looks different with respect to the first cabled connection when I switched on the PC: the Ethernet 3 does not have the IPv6 and Temporary IPv6 Addresses and it mirrors the settings of the Wireless LAN Adapter seen just above.
I really need your help to sort this issue out because it is very frustrating: each morning I need to connect with Lan Cable, then disconnect it, switch on WiFi, wait for GlobalProtect to connect, then switch off WiFi and finally connect LAN Cable again.
1. Can you try to disable IPv6 binding on your OS? In windows run ncpa.cpl, right click & properties of 'PANGP virtual Ethernet adapter' (or Ethernet 3) and unselect IPv6 binding. This should completely remove IPv6. Reboot and test.
In your Globalprotect portal configuration, 'Resolve All FQDNs Using DNS Servers Assigned by the Tunnel (Windows Only)' option if set to 'Yes' - will enforce the client machine to resolve all the DNS queries through the tunnel.
If set to 'No'. This allows Windows endpoints to send DNS queries to the DNS server set on the physical adapter if the initial query to the DNS server configured on the gateway is not resolved. This option retains the native Windows behavior to query all DNS servers on all adapters recursively but can result in long wait times to resolve some DNS queries.
The first item is on your workstation and can be tested locally but the second item could potentially affect all users. I think your IT can see if this is the cause of your issues by nslookup commands on your workstation in ETH/WiFi mode. In addition - check the firewall logs to see if and where your IPv6 packets go
I've tried solution 1. and it worked! First I tried disabling the IPv6 Protocol on PANGP virtual Ethernet adapter (which is Ethernet 2 on my configuration) and issue was still present. Then I also disabled IPv6 Protocol on the 'real' connection, so Ethernet 3 and this time it worked!
Turning off IPv6 binding on one interface should not turn it off on another.
So, turning it off on the GP interface (Ethernet 2), that should not turn it off on the physical LAN Ethernet (Ethernet 3) yet comparing the last screenshot to the first few, IPv6 is completely disabled.
But one thing I notice from the first post is that the Ethernet 3 seems to be getting issued an IPv6 from the router from somewhere in addition to its link-local IPv6 address, first with what might be a DHCP suffix as the temporary IPv6, then switching to MAC based IP. Not sure if IPv6 prefix of FDD7 has any IP type significance like FE80 has.