Help - trouble breaking in Speedplay Zero pedals
Emily
Speedplay Zeros (ti), because I didn't need so much float and found that
my heels were hitting the crankarms from time to time. I am having a
terrible time clipping into the Zeros, especially with my first foot. I
can't clip in at all from a dead stop as I normally do, despite putting
all my weight into it. Instead, I have to start pedaling without
clipping in, then I am able to clip in after several attempts. I've
been riding clipless for several years so am not a newbie at this; are
these pedals just exceptionally hard to break in?
They are also harder to clip out of than my X-2s (or the Eggbeater
Candies I have on my mtb), but I can manage that.
I am a petite female (5'2", 105 lbs) and just can't seem to get enough
force to clip in. I love the pedals once I am clipped in, so I do want
to make this work; I am just not sure how. Are they easier to clip in
if I set them for more float? Right now I have them set for zero float
inwards (don't need it since I toe out a bit) and about 3 degrees
outwards, which seems fine for my knees - I just can't clip in!
Thanks much,
Emily
Bestest Handsander
news:d3hs7...@enews1.newsguy.com...
As I understand it, the float and clip in are two separate functions
unrelated to each other (at least that's what Speedplay's literature says.
I've ridden Zeros for the past two years. I've found that when I have
trouble clicking in, it's usually been a placement problem. If it doesn't
go in on the first push, I lift up my foot off of the pedal and then push
again. Seems to work. Also, make sure you didn't over-torque the cleat
when installing it on your shoe. If the cleat doesn't have a flat platform,
and you crank down on the screws, the metal ring can bend slightly like a
Pringles chip. That also prevents easy engagement. Another thing to check
would be to make sure you didn't get the Track version of the cleats. They
are much tighter.
HTH, but as always, YMMV
Bob Wheeler
The adjustment of Speedplay's is difficult. I had zero's on my bikes for
about a year, and finally replaced them with SPD's. It is of course
possible that I never got things right, but I did go through several
cleats and several adjustments in the attempt. The design requires a
nice adjustment of the screws which are held in place by Loctite, rather
than screw pressure. I was never able to clip in from a dead stop, and
had a lot of trouble otherwise. It was essential to lubricate the cleats
for each ride with White Lightning, and even then it was sometimes hard
to clip in. I finally decided that they were more fuss than they were
worth. (Anyone want to buy some cheap? I have three pairs.)
--
Bob Wheeler --- http://www.bobwheeler.com/
ECHIP, Inc. ---
Randomness comes in bunches.
Qui si parla Campagnolo
First enssure you have the correct shim in and the cleat is very flat on
the bottom of the shoe. If it is bent at all, use the other shim to
attempt to get the cleat flat. using extra shims may help as well. A
flat cleat is essential to proper use of Zeros.
Pat
: Speedplay Zeros (ti), because I didn't need so much float and found that
: my heels were hitting the crankarms from time to time. I am having a
: terrible time clipping into the Zeros, especially with my first foot. I
: can't clip in at all from a dead stop as I normally do, despite putting
: all my weight into it. Instead, I have to start pedaling without
: clipping in, then I am able to clip in after several attempts. I've
: been riding clipless for several years so am not a newbie at this; are
: these pedals just exceptionally hard to break in?
I am having the same problem with my new Speedplay Zeros. I complained about
it at the LBS yesterday evening and was told to "back off" the tightness of
the 4 screws that hold the cleat to the bottom of the shoe. Supposedly, this
allows the springs to have more looseness. I haven't tried it yet, but I
plan to do it this evening. For me, the SPD pedals are a non-started because
of immediate "hot foot" problems. I changed from Looks to Speedplay
primarily for the float.
Pat in TX
Mike Jacoubowsky
> the bottom of the shoe. If it is bent at all, use the other shim to
> attempt to get the cleat flat. using extra shims may help as well. A flat
> cleat is essential to proper use of Zeros.
Agreed. But in general, don't you see more issues with cleats, and the ease
of getting into them, with zeros than with X2s? We certainly see a lot more
broken cleat springs with zeros, and in general, I don't recommend them for
lighter-weight riders.
--Mike-- Chain Reaction Bicycles
www.ChainReactionBicycles.com
"Qui si parla Campagnolo" <pe...@vecchios.com> wrote in message
news:1113396579.5d7f8ee3a0c7599d97d6a84595a93b61@teranews...
Emily
messed with my cleats today. He first moved the position of them on my
shoes to make sure that they were directly on the ball of my foot (they
were slightly to the outside so not as well aligned as they should have
been). He discovered that the screws that attach them to my shoes were
a little loose and tightened them up. He then clipped each one in and
out of the pedal about 100 times (the things we do for love!) It's too
cold and wet to ride tonight, but I did try clipping in several times in
the garage and was able to do it (even from a dead stop) at last. The
second foot went in even easier. The first foot (left) definitely
required some force, but was not impossible like it was when I rode this
weekend. So maybe things will be better from here on out. :-)
I do wish I'd known beforehand that these pedals weren't recommended for
lighter riders, but now that I've spent the cash, I am determined to
make them work!
Thanks again - what a helpful group this is!
Emily
Qui si parla Campagnolo
>>First enssure you have the correct shim in and the cleat is very flat on
>>the bottom of the shoe. If it is bent at all, use the other shim to
>>attempt to get the cleat flat. using extra shims may help as well. A flat
>>cleat is essential to proper use of Zeros.
>
>
> Agreed. But in general, don't you see more issues with cleats, and the ease
> of getting into them, with zeros than with X2s? We certainly see a lot more
> broken cleat springs with zeros, and in general, I don't recommend them for
> lighter-weight riders.
yes and I think because the pedal is 'locked' into the spring of the
Zero cleat where it just engages the spring of the X-2.
Qui si parla Campagnolo
Whoever told you this fairy tale? Because of the diffuculty to get into
them? I think the issue is smaller shoes and the resulting roundness of
the shoe rather than weight. Even a small person, weighing in the buck
.05 range can exert enough force to get into pedals.