Proofread, please.

[Jonathan Baldwin]

b3-Mouse2 (NO Flash - USB A) - Google Sheets

For the life of me, I don't know why this spreadsheet is not working. Plus, the quad stick takes forever to switch over to it, so something must be wrong. I have only one other profile loaded to the quad stick, and it works fine.

[Fred Davison]

Enable USB-A Host mode must off in the QMP settings, saved, wait a few seconds for it to be read, and then quadstick restarted, for enable_usb_a_device to work.

If you are still having trouble, swap the order of these two sheets

On Thu, Feb 26, 2026 at 6:21 PM Jonathan Baldwin <bonele...@gmail.com> wrote:

b3-Mouse2 (NO Flash - USB A) - Google Sheets

For the life of me, I don't know why this spreadsheet is not working. Plus, the quad stick takes forever to switch over to it, so something must be wrong. I have only one other profile loaded to the quad stick, and it works fine.

--
You received this message because you are subscribed to the Google Groups "QuadStick" group.
To unsubscribe from this group and stop receiving emails from it, send an email to quadstick+...@googlegroups.com.
To view this discussion visit https://groups.google.com/d/msgid/quadstick/096be898-937c-446e-bf36-486456e6f32an%40googlegroups.com.

[Jonathan Baldwin]

Thank you. Just one more profile to proofread, this following sheet works, but only the first sheet, not any of the others. It's as if I only have one sheet in the profile.  

[Jonathan Baldwin]

b3-World of Warcraft - Google Sheets

[Fred Davison]

In the preferences sheet:

sip_puff_delay_soft

125

ms

The first sheet has:

increment_mode

normal

mp_center_sip

kb_right_shift	normal	mp_center_sip_soft
kb_2	normal	mp_center_sip_soft

If the soft sip delay is only 1/8-th of a second, it might be difficult to get past the soft pressure before it times out and you hear the beep and get a shift-2 instead of a click and an increment_mode.

The second sheet has:

decrement_mode

normal

mp_center_sip

So there is no way to get to the third sheet.

The third sheet has:

increment_mode	normal	right_sip
decrement_mode	normal	right_sip_soft

The fourth sheet has:

increment_mode	normal	right_sip
decrement_mode	normal	right_puff

It could be confusing to have different inputs mapped to the increment/decrement mode functions on each sheet.

These last two sheets are not accessible anyway and may just be left overs.

[Jonathan Baldwin]

So I'm still perfecting my World of Warcraft profile. In this one, I can get it to go to Sheets 1, 3, and 4.  However, it is ignoring page 2. I can only assume it has something to do with the increment-decrement function, but I don't know why I have it wrong.

[Fred Davison]

It is missing some increment/decrement mode rows.

mode 1 has:

decrement_mode

normal

right_sip

mode 2 has:

increment_mode

normal

right_sip

mode 3 has:

increment_mode

normal

right_puff

mode 4 has:

increment_mode	normal	right_puff
decrement_mode	normal	right_sip

There is no way to go from either mode 1 or 3 to mode 2.  The other thing is the sip vs puff are not consistent between modes.  Sometimes the sip increments the mode and other times it decrements the mode.  That could get very confusing.

[Jonathan Baldwin]

It seemed to work, until I duplicated the first sheet. What do you recommend? Should I create increment and decrement lines on each one of the sheets, or can I set it up so that decrement is always done with a sip and increment is always done with a puff?  

[Fred Davison]

I think you should make all the sheets the same as mode 4 with consistent increment/decrement rows.