Bosch Plena Voice Alarm System Software 2.13 [WORK] Download
Carlita Giandomenico
Based on a Plena voice alarm controller unit, VAS can handle up to 6 zones with a built-in message manager, emergency microphone and a built-in 240 W power amplifier. By connecting additional 6-zone routers to the Plena VAS, the number of zones extends to a 120-zone capacity. The power per zone is freely distributable per zone and it can be over 1000 Watts per router (or 6 zones). In addition, 8 call stations with 32 call station keypads with programmable keys can be interconnected for message routing. Additional PLENA amplifiers can be added to create two-channel systems. The Plena Voice Alarm system is configured via a Windows. A system design tool is available to support the pre-sales design process, but give us a call for assistance and expert advice on configuring your Plena VAS system.
9 Plena Voice Alarm System Safety en 9 1 Safety 1.1 Important Safeguards Prior to installing or operating this product, always read the Important Safety Instructions which are available as a separate document ( x). These instructions are supplied together with all equipment that can be connected to the mains. 1.2 Important Notices When using routers, keypads or more than one call station, configure the controller using the supplied software. Use shielded cable (Cat-5) between the routers and the controller. Do not connect the shield to both the controller and the router! The factory default setting of the Plena Voice Alarm Controller is as follows: Stand-alone unit configured for an ISO compliant system when used with a spare power amplifier from the Plena range and compliant wiring and loudspeakers. One channel system. Supervision on for: Loudspeaker lines (90 seconds interval, 15% accuracy) Main and spare power amplifier Short to ground ( Ground short ) Mains and battery power EMG mic Memory For the remote controls to function, all firmware must be version 2.0 or higher. The factory-installed firmware is indicated on every component of the voice alarm system (Controller, Router, Call Station, Fireman s Panel, Remote Control, Remote Control Extension, Remote Control kit, Remote Control Extension kit). If a label is not present, the firmware version is 1.x. Bosch Security Systems B.V. Installation and Operation manual x (V2.16) V
13 Plena Voice Alarm System System overview en 13 3 System overview 3.1 Voice Alarm System The Plena Voice Alarm System is a public address and voice alarm system in which all the necessary features for compliance to evacuation standards such as IEC60849, NEN2575, BS5839/8 and EN54-16 are integrated Application types Typically, the Plena Voice Alarm System is used to create small systems that must comply to evacuation standards, medium-sized systems in which one call channel is enough and large systems that consist of many small zones Application areas The application areas of the Plena Voice Alarm System include: Supermarkets, shops Factories High-rise buildings Office buildings Schools Recreational facilities Hotels Small airports Plena The Plena Voice Alarm System is part of the Plena product range. Plena provides public address solutions for places where people gather to work, worship, trade or simply enjoy themselves. It is a family of system elements that are combined to create public address systems tailored for virtually any application. The range includes mixer, pre, system and power amplifiers, a source unit, digital message manager, feedback suppressor, conventional and PC call stations, an All-in-One system, an audio interface, a timer, a charger, a loop amplifier, a BGM source and a voice alarm system. Each element is designed to complement all others thanks to matched acoustical, electrical and mechanical specifications Praesideo It is possible to combine the Plena Voice Alarm System with e.g. a Praesideo digital public address and emergency sound system, or a Promatrix or other system. When an audio output of Praesideo is connected to a VOX audio input of the Plena Voice Alarm System, calls that are made by the Praesideo system overrule the calls that are made with the Plena Voice Alarm System. Bosch Security Systems B.V. Installation and Operation manual x (V2.16) V
14 14 en System overview Plena Voice Alarm System 3.2 Voice alarm controller The Voice Alarm Controller is the heart of the Plena Voice Alarm System. The voice alarm controller distributes emergency calls, business calls as well as background music (BGM) to up to 6 loudspeaker zones. Figure 3.1 Voice Alarm Controller NOTICE! When the voice alarm controller has been purchased in the Asian-Pacific Region, the emergency button has a different cover Hand-held microphone The voice alarm controller is equipped with a hand-held microphone, which can be used to make emergency calls Internal power amplifier The voice alarm controller has a 240 W internal power amplifier, which can be used in 1- channel or 2-channel mode. In the 1-channel mode, all calls and BGM are amplified by the internal power amplifier. If desired, an external power amplifier can be connected for spare switching. In the 2-channel mode, the BGM is amplified by the internal power amplifier, whereas the calls are amplified by an external power amplifier Internal message manager The voice alarm controller has an internal message manager, which maps wave files (.wav) to messages that can be played by the Plena Voice Alarm System Supervision All necessary supervision features for compliance to evacuation standards are integrated into the voice alarm controller. If supervision is enabled and a fault is detected, the voice alarm controller lights a LED on its front panel that indicates the cause of the fault Trigger inputs The voice alarm controller has a terminal block to which 6 emergency (EMG) and 6 business trigger inputs can be connected. Third party systems can use the trigger inputs to start emergency and business calls in the Plena Voice Alarm System Remote control With the Voice Alarm Remote Control, it is possible to control the voice alarm controller from another site. The remote control is also available as kit (Voice Alarm Remote Control Kit) for creating customized solutions. The maximum number of remote controls that can be connected to the voice alarm controller is 2. A special type of remote control is the Fireman s Panel x (V2.16) V Installation and Operation manual Bosch Security Systems B.V.
15 24V DC out VO X Switch 24V DC out VOX Switch 10 k 10 k N6 63 Plena Voice Alarm System System overview en Controls, connectors and indicators Plena Voice Alarm Controller 0 db -6dB -20dB Fault Indicators Processor reset Network Call/EMG Music/Spare Mains Battery Message EMG mic A Disabled B Zone1 Zone2 Zone3 Zone4 Fault Ack EMG Zone select Alarm Ground short Input RCP Router Zone5 Zone6 Reset Zone1 Zone2 Zone3 Zone4 Zone5 Zone6 Alert message All call Select Zone select Alarm message Indicator test CD/Tuner Aux EMG mic Int Booster Ext Booster A 100 V Z V Z V Z V Z V Z5 0 1 Channel 2 Channel BGM/ C all BGM/ Spare N.C./Spare Call Override/Trigger Output B 24V 100 V Z1 Z1 0 Z2 100 V Z2 0 Z3 100 V Z3 Z V Z5 Z4 0 Z6 100 V Z5 TRG 1 0 NC NC NO COM EMG NO COM NC COM Fault NO NC COM Call NO NC 24V Volume Override NO TRG2 Trigger input/24v DC out Emergency Business Call station For ser vice only SEL1 Monitor SEL0 APR mode Firmware Supervision Upgrade 2ch operation 1 Reserved Off 2 On Impedance Calibration LBB 1 990/ Plena Voice Alarm Controller Max. output power 360W Rated output power 240W V, 50/60Hz S/N. Design & Quality The Netherlands USB Off On Made in China Reserved Reserved Line fuse T6.3L250V for230v AC T10L250V for115v AC 115V 230V Apparatus delivered C onnected for 230V Power Rated input power :760VA 100 V Z6 0 Ext 100 V B ooster In 0 DC In 24V 100 V Z V Int 70 V Booster Out V C all out GND Out External Booster In CD/Tuner AUX PC L R GND Mic/Line Vox Vox Speech filter Phantom power Off On Remote Control Panel EMG. Mic 1 2 Digital Monitoring Mess age Speaker Router Warning This apparatus must be earthed Figure 3.2 Front and rear views of the voice alarm controller See Figure 3.2 for an overview of the controls, connections and indicators on the voice alarm controller: 1. Power LED/VU Meter: A combined power indicator and VU meter. The green power LED is lit if the voice alarm controller is connected to the mains or back-up power and switched on. The VU meter indicates the master VU level: 0 db (red), 6 db, -20 db (yellow). 2. Fault indicators: Twelve yellow system fault LEDs (Processor reset, Network, Call/EMG, Music/Spare, Ground short, Input, Mains, Battery, Message, EMG mic, RCP and Router) and twelve yellow loudspeaker line fault LEDs. Fault indication is only possible if supervision is enabled (see section ). If supervision is disabled, the yellow Disabled LED is lit. 3. Fault state buttons: Two buttons to acknowledge (Ack) and reset (Reset) the fault state (see section 7.5 ). 4. Emergency state buttons: Two buttons to acknowledge (Ack) and reset (Reset) the emergency state (see section 7.4 ). Bosch Security Systems B.V. Installation and Operation manual x (V2.16) V
16 16 en System overview Plena Voice Alarm System 5. Emergency call zone selectors: Six buttons to select the zones to which the emergency call must be distributed (see section 7.4 ). Each button has a green and a red LED. The six red LEDs indicate the zones that are selected for the emergency call. The six green LEDs indicate the zones in which a business call is running. 6. BGM zone selectors: Six buttons to select the zones to which the BGM is distributed (see section 7.2 ). Each button has a green LED and a rotary knob. The six green LEDs indicate the zones to which BGM is distributed. The six rotary knobs are local volume controls that can be used to adjust the volume of the BGM in each zone. Each volume control knob has six settings. 7. BGM master volume control: A rotary knob to set the master volume of the BGM (see section 7.2 ). 8. BGM source selector: A button to select the BGM source (CD/Tuner or Aux). The selected source is indicated with a green LED (see section 7.2 ). 9. BGM tone controls: Two rotary knobs to control the high and low frequencies of the BGM (see section 7.2 ). 10. All call button: A button to select all zones. This button is only available in the emergency state (see section 7.4 ). 11. Indicator test button: A button to test all LEDs on the front panel of the voice alarm controller, and connected voice alarm routers, remote control panels, remote control extensions and fireman s panels. All LEDs are lit as long as the button is pushed (see section 7.5 ). 12. Emergency button: A push button to put the system in the emergency state (see section7.4 ). 13. Alert message button: A button to select the alert message. This button is only available in the emergency state (see section 7.4 ). 14. Alarm message button: A button to select the default alarm message. This button is only available in the emergency state (see section 7.4 ). 15. Microphone socket: A socket to connect the hand-held emergency microphone (see section ). 16. Bracket: A bracket for the hand-held emergency microphone that is supplied with the voice alarm controller. 17. Monitoring speaker: Built-in monitoring speaker. 18. Zone outputs: Six zone outputs to connect loudspeakers to the voice alarm controller. Each zone output consists of two loudspeaker line outputs (see section ). 19. Override outputs: Six volume override outputs to override local volume controls in each zone (see section ). 20. Status outputs: Three status outputs to send the status of the Plena Voice Alarm System to third party equipment (see section ) x (V2.16) V Installation and Operation manual Bosch Security Systems B.V.
df19127ead