Finger Print Module

[Aron Eugine]

HiI am using the Adafruit fingerprint library and I have attached them too.

I just want my module to print the template data of the finger ( hex data ) whenever i scan in the serial monitor ,

I dont want to give any ID or store it the flash memory of the module

I want my code to run and turn on my module and if a finger is kept it needs to print the Template data (hex) in serial monitor .

Could anyone help with this ? I am trying on my own and will post if there is output .

See here

show_fingerprint_templates.ino

this code will show the template data of the fingerprints stored in the flash of the module.

right now I need to run my module and ready to read fingerprint when a finger is placed I need to print the Template data of the respective fingerprint .

Dude Please ....

I do have all these documentation which was with the library I downloaded from GitHub .

Did you understand my requirement ? I have clearly mentioned it step by step . I could even repeat it if you need ,unless you give me a solution

I just want my module to print the template data of the finger ( hex data ) whenever i scan in the serial monitor ,

I dont want to give any ID or store it the flash memory of the module

I want my code to run and turn on my module and if a finger is kept it needs to print the Template data (hex) in serial monitor .

In other words......

I need my Fingerprint sensor to run continously to detect any finger that is going to be placed.

When a finger is placed , the template data need to be stored in a default location ( say ID# 1 ) and I need to display the HEX data of the fingerprint at the same time in the serial monitor .

If another finger is placed I need it to store it in the same location ID#1 and display the HEX data in serial monitor .

All I need is the HEX data of the fingerprint for my android app.

Help me out ,

I attach the codes that could help you

My fingerprint scanner also stopped working. No issues with the passcodes. Custer support was no help because its beyond the warranty date. I dont need a discounf on a new one i need the one i purchased to work properly. If so many people are having the same issue it must be some sort of defect. Has anyone been able to fix theirs?

If your fingerprint sensor light was off when pressing your finger on it, please check the wire and carefully reconnect the connector between the Interior Assembly and the Exterior Assembly. Guide to Disconnect/Reconnect the Keypad Wire

I can't find fingerprint sensors settings in Ubuntu 22.04 installed on my notebook (XPS 13 Dell). I've tried "settings > Users", but there is no fingerprint option there. Do I have to install separately or it is provided by Ubuntu 22.04?

I'm also running the same setup and had the same issue but the fix is pretty straightforward. First of all makes sure that the OS recognises that the fingerprint sensor exists. You can do this by running

If you get any dependency errors just apt install the relevant dependency and try again. After you install everything you should be able to see a fingerprint option appear in the Users settings. According to the original source there is a reboot necessary.

Multiple users ( including myself ) have reported this to work now, so I think the packages will be part of 22.04 soon, just keep an eye on the bug (they are in the proposed channel now, which you can enable to test too).

[update]A fix has been released as a result of the bug report. Make sure to read it and see if your problem is solved. A full update should give you a working setup if you were affected by the bug[/update]

The sensor works like this. It is an optical sensor, which means it analyzes the photo of a finger. It then renders the image, makes some calculations, finds the features of that finger and then searches in its memory for a fingerprint with the same characteristics. It can achieve all that in less than a second!

This module can store up to 1000 fingerprints in its memory and its false acceptance rate is less than 0.001% which makes it pretty secure! Great! We get all that in a very easy to use module and with very low cost! It is a really impressive technology!

First of all we have to upload the enroll example to our Arduino board. We go to File -> Examples -> Adafruit Fingerprint Sensor Library -> Enroll. With this example program we can store fingerprints in the FLASH memory of the module. We upload the sketch and we open the Serial Monitor. The program ask us to enter the ID to enroll. Then we place the finger on the sensor twice as we are instructed and the fingerprint is stored! You can store as many as 1000 fingerprints this way!

As always you can find the code of the project attached in this Instructable. Since I update the code from time to time, for the latest version of the code please visit the project's website: -fingerprint-sensor-module...

Is it possible to salvage a fingerprint scanner from an old and dead smartphone and use it with Arduino? I am not talking about writing an android program and send data to Arduino over Bluetooth or WiFi, I am talking about wiring up fingerprint scanner of a mobile phone to Arduino.

Long-shot, but if the phone is still functional enough to unlock with a fingerprint, try sensing the overall screen brightness when locked and when unlocked, and use that as the "Fingerprint matched" signal. Obviously this won't work with a truly dead phone.

A lot of processing goes into reading and storing or matching a finger-print. The magic is in the software, not (only in) the sensor. An Arduino (Uno class or similar) is way under-powered for the task. Perhaps one of the Arm- or other high-end Arduinos would have the capability if you had or could write the necessary software.

Possible but not directly as the arduino compatible fingerprint sensor contains image formation and saving mechanism which means that those sensors scan a fingerprint form image and send the scan status not the finger print image....

Using FPGAs to tackle some of these problems is possible, but also very challening. If you need to ask this question, this is most likely out of scope. (A friend of mine did program a FPGA for his physics master on university. It can be very difficult.)

FINGER is a fingerprint recognition sensor designed to provide reliable and convenient biometric fingerprint recognition capabilities. It features the integrated FPC1020A capacitive fingerprint recognition module, which enables functions such as multi-fingerprint enrollment, image processing, feature extraction, fingerprint matching, and searching.

Utilizing the UART communication protocol, FINGER ensures secure and efficient data transmission. Its compact design and low-power operation make it suitable for various projects, offering both reliable security levels and optimal user convenience. If you are looking to incorporate biometric fingerprint recognition into your project and require a stable and dependable mechanism for enrollment, verification, and management, FINGER Unit provides an excellent solution.

To use FINGER, simply connect it to PORT C, and it will communicate with the M5Core device via UART protocol.

I'm currently working on my semester project which includes interfacing the R305 Fingerprint Sensor to TM4C123 microcontroller (by Texas Instruments).The fingerprint sensor communicates to the microcontroller through UART interface and so it has 4 pins to connect to the microcontroller: Vcc, GND, Tx, Rx, as given in the datasheet at the following address.

From the datasheet, I could understand that in order to assure the perfect connection between the microcontroller and the fingerprint sensor, the first thing is the HandShake, in which a certain Command Packet is sent to the sensor and the sensor returns the corresponding Acknowledgement Packet. But in my case, I'm sending the command packet to the fingerprint sensor and the sensor is sending nothing back.The sensor works fine with arduino when using the Adafruit Library, but I have to work with the TM4C123 MCU for my project.I'm using Keil uvision 4 as an IDE for my MCU.

These MCU work internally are very different - different registers, different process for using them, different gotchas to look out for, etc. If you're looking at tackling a new MCU family, be prepared to effectively learn a new "language".

The Finger Print Sensor is one optical fingerprint sensor which will make fingerprint detection and verification adding super simple.There's a high powered DSP chip AS601 that does the image rendering, calculation, feature-finding and searching. You can also enroll new fingers directly - up to 162 finger prints can be stored in the onboard FLASH memory. There's a red LED in the lens which will light up during taking photos so that you know its working condition. It is easy to use and by far the best fingerprint sensor you can get.

The platforms mentioned above as supported is/are an indication of the module's software or theoritical compatibility. We only provide software library or code examples for Arduino platform in most cases. It is not possible to provide software library / demo code for all possible MCU platforms. Hence, users have to write their own software library.

The Finger Print Sensor module is typically used in safes - there's a high powered DSP chip that does the image rendering, calculation, feature-finding and searching. Connect to any microcontroller or system with TTL serial, and send packets of data to take photos, detect prints, hash and search. You can also enroll new fingers directly - up to 162 finger prints that can be stored in the onboard FLASH memory. There's a red LED in the lens which will light up during taking photos so that you know its working condition.

The library can enroll and search so its perfect for any project. It can help you get running in under 10 minutes. There are basically two requirements for using the optical fingerprint sensor. First one, you'll need to enroll fingerprints - that means assigning ID #'s to each print so you can query them later. Once you've enrolled all your prints, you can easily 'search' the sensor, asking it to identify which ID (if any) has currently been photographed.

3a8082e126