Re: Open Pilot Cc3d Software 14

[Periandro Hawkins]

Open Pilot CC3D Software 14: A Guide to Download and Install

If you are looking for a reliable and easy-to-use flight controller for your FPV racing drone, you might want to consider the OpenPilot CC3D. This is a popular open-source autopilot system that supports various types of multirotors, such as quadcopters, hexacopters, and octocopters. The CC3D board has a powerful STM32F103T8U6 microcontroller that runs at 72 MHz and has 64 KB of flash memory and 20 KB of RAM. It also has a 3-axis gyroscope, a 3-axis accelerometer, and a flexible port that can be configured as UART, I2C, or PWM output.

open pilot cc3d software 14

Download Zip ---> https://vittuv.com/2z0Fr4

One of the advantages of using the OpenPilot CC3D is that it comes with a user-friendly graphical configuration software called OpenPilot GCS (Ground Control Station). This software allows you to set up your CC3D board, calibrate your sensors, tune your PID values, and monitor your flight data in real-time. You can also choose from different flight modes, such as manual, stabilized, rate, attitude, and GPS-assisted.

However, before you can use the OpenPilot GCS software, you need to download and install the correct version that matches your CC3D firmware. In this article, we will show you how to find and download the OpenPilot CC3D software 14, which is one of the older versions of the software that supports the CC3D board. We will also guide you through the installation process and the basic steps to set up your CC3D board using the OpenPilot GCS software 14.

How to Download the OpenPilot CC3D Software 14

The OpenPilot CC3D software 14 is not available on the official website of OpenPilot anymore, as it has been replaced by newer versions that support more advanced boards such as Revolution and Pyrodrone F4. However, you can still find some download links for the OpenPilot CC3D software 14 on some online forums and websites. Here are some of the sources where you can download the OpenPilot CC3D software 14 for different operating systems:

• For Windows: You can download the OpenPilot CC3D software 14 for Windows from this Google Drive link. This is a zip file that contains the executable installer for the software.

• For Mac OS X: You can download the OpenPilot CC3D software 14 for Mac OS X from this broken link. This is a dmg file that contains the installer for the software. However, this link may not work anymore, so you might have to look for other sources or use a different operating system.

• For Linux: You can download the OpenPilot CC3D software 14 for Linux from this page. This is a tar.gz file that contains the source code for the software. You will need to compile it yourself before you can use it.

Alternatively, you can also use newer versions of the OpenPilot GCS software that still support the CC3D board, such as LibrePilot or dRonin. These are forked projects from OpenPilot that have continued to develop and improve the software. You can find more information about these projects on their respective websites:

• [LibrePilot]

• [dRonin]

How to Install the OpenPilot CC3D Software 14

Once you have downloaded the OpenPilot CC3D software 14 for your operating system, you can proceed to install it on your computer. The installation process may vary depending on your operating system, but here are some general steps that you can follow:

• Extract the downloaded file to a folder on your computer.

• Run the installer file and follow the instructions on the screen.

• Accept the license agreement and choose a destination folder for the software.

• Select the components that you want to install, such as drivers, firmware, documentation, etc.

• Wait for the installation to complete and click finish.

• Launch the OpenPilot GCS software from your start menu or desktop shortcut.

If you encounter any problems during the installation, such as driver issues, you can refer to the troubleshooting section of the OpenPilot wiki for some possible solutions.

How to Set Up Your CC3D Board Using the OpenPilot CC3D Software 14

After you have installed the OpenPilot CC3D software 14 on your computer, you can start to set up your CC3D board using the software. The OpenPilot GCS software 14 has a built-in wizard that will guide you through the basic steps to configure your CC3D board, such as updating the firmware, selecting the vehicle type, calibrating the sensors, and tuning the PID values. Here are some of the steps that you need to follow:

• Connect your CC3D board to your computer via a USB cable. Make sure that your board is not connected to the battery or the ESCs yet.

• Open the OpenPilot GCS software 14 and click on the green "Vehicle Setup Wizard" button on the top right corner of the screen.

• A pop-up window will appear. Click on "Next" to start the wizard.

• On the Firmware Update page, check the "Erase all settings" box and click on "Upgrade". The software will automatically detect your board and update it with the latest firmware. You may need to reconnect your board to the USB cable as instructed by the software.

• On the Board Identification page, click on "Next" to confirm that your board is a CC3D.

• On the Input Type page, select your receiver input type from the drop-down list. This depends on what type of receiver you are using, such as PWM, PPM, S-Bus, etc. Click on "Next" to proceed.

• Your board will reboot and you will see a green light on it. On the Vehicle Type page, select "Multirotor" from the options and click on "Next".

• On the Multirotor Configuration page, select your multirotor type from the drop-down list. This depends on how many motors and arms your multirotor has, such as Quadcopter X, Hexacopter Y6, etc. Click on "Next" to proceed.

• On the ESC Type page, select your ESC type from the drop-down list. This depends on what type of ESCs you are using, such as RapidESC, OneShot125, etc. Click on "Next" to proceed.

• On the Configuration Summary page, review your settings and make sure they are correct. If not, go back and change them. If they are correct, click on "Connection Diagram" to see how to wire up your board to your ESCs and receiver. Follow the diagram and connect your board accordingly. Click on "Save" to close the diagram and click on "Next".

• On the Level Calibration page, make sure that your multirotor is on a level surface and click on "Calculate" to calibrate your board's level. Wait for a few seconds until you see a message saying "Leveling successful". Click on "Next" to proceed.

• On the ESC Calibration page, read the instructions carefully and make sure that you understand them. Check all three safety boxes and click on "Start". Follow the instructions on how to calibrate your ESCs by plugging in and unplugging your battery while moving a slider on the screen. You should hear some beeps from your ESCs indicating that they are calibrated. Click on "Next" when done.

• On the Output Calibration page, read the instructions carefully and make sure that you understand them. Click on "Start" and move a slider slowly to test each motor individually. You should see each motor spin up and down as you move the slider. Make sure that each motor spins in the correct direction and at a similar speed. If not, you may need to reverse some wires or swap some channels on your receiver. Click on "Stop" when done and click on "Next".

• On the Initial Tuning page, select a preset tuning option from the drop-down list that matches your multirotor size and weight. This will set some initial PID values for your board that you can later adjust manually if needed. Click on "Next" to proceed.

• On the Final Page page, click on "Save" to

  save your settings to your board. You have completed the basic setup of your CC3D board using the OpenPilot CC3D software 14. Click on "Finish" to close the wizard.

Congratulations! You have successfully downloaded, installed, and configured your CC3D board using the OpenPilot CC3D software 14. You can now test your multirotor and enjoy flying it. However, you may still need to fine-tune your PID values and adjust some other settings to optimize your flight performance. You can do this by using the Manual Control page and the Stabilization page of the OpenPilot GCS software 14. You can also explore other features and options of the software, such as telemetry, logging, OSD, etc. For more information and guidance, you can refer to the documentation and tutorials of the OpenPilot wiki.

We hope that this article has helped you to understand how to use the OpenPilot CC3D software 14 for your FPV racing drone. If you have any questions or feedback, please feel free to leave a comment below. Happy flying!

3b01f9094b