Omap36-zoom3 get stuck while booting

[Thomas Ng]

Hi,
I am trying to boot the RLS25.INC2.7P2rc0 from OMAP36zoom3 MDP,
however the system get stuck (please refer to the console log below).
The screen shows the "splash screen" and "android _", then black out
forever.
Can someone please give me some advise on this? Thanks!


========================================================
U-Boot 1.1.4-ge891bbac-dirty (Mar 18 2010 - 17:47:41)

OMAP3630-GP rev 1, CPU-OPP2 L3-200MHz
OMAP3630Zoom3 1.0 Version + mDDR (Boot NAND)
DRAM: 1024 MB
NAND:512 MiB


In: serial
Out: serial
Err: serial
Battery levels: main 3951 mV, backup 3047 mV
Hit any key to stop autoboot: 3 2 1 0
MMC1 Initalization OK

2610804 bytes read
Booting from mmc ...
## Booting image at 81c00000 ...
Image Name: Linux-2.6.29-omap1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2610740 Bytes = 2.5 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
OK

Starting kernel ...

K
OK

Starting kernel ...


Verifying Checksum ... K
OK

Starting kernel ...


Verifying Checksum ... Linux version 2.6.29-omap1 (iwow@iwow-
laptop) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #1 PREEMPT
Thu Jul 29 16:42:07 SGT 2010
CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: OMAP ZOOM3 board
Memory policy: ECC disabled, Data cache writeback
Truncating RAM at a0000000-bfffffff to -afffffff (vmalloc region
overlap).
L2 CACHE is enabled in bootloader
OMAP3630 ES1.1
DIE ID: 3A5200011FF00000015A5E591100F010
SRAM: Mapped pa 0x40200000 to va 0xfc800000 size: 0x100000
Reserving 4194304 bytes SDRAM for VRAM
Built 1 zonelists in Zone order, mobility grouping on. Total pages:
195072
Kernel command line: console=ttyS3,115200n8 root=/dev/mmcblk0p2
rootdelay=3 init=/init
Clocking rate (Crystal/DPLL/ARM core): 26.0/400/600 MHz
Reprogramming SDRC
GPMC revision 5.0
IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
OMAP34xx GPIO hardware version 2.5
PID hash table entries: 4096 (order: 12, 16384 bytes)
OMAP clockevent source: GPTIMER1 at 32768 Hz
Console: colour dummy device 80x30
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 512MB 256MB = 768MB total
Memory: 762880KB available (4912K code, 915K data, 200K init)
Calibrating delay loop... 597.64 BogoMIPS (lpj=2334720)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 720 bytes
regulator: core version 0.5
NET: Registered protocol family 16
[CONN_CFG] Connectivity board init
[CONN_CFG] Connectivity board init for OMAP3+WL127x
[CONN_CFG] wl127x_vio_leakage_fix
[CONN_CFG] Adding Connectivity platform device
MUX: setup H18_34XX_GPIO163 (0xfa00219a): 0x0108 -> 0x011c
MUX: setup B24_34XX_GPIO101_OUT (0xfa00211a): 0x0104 -> 0x0004
MUX: setup W21_34XX_GPIO162 (0xfa002198): 0x011c -> 0x0104
MUX: setup A24_34XX_GPIO94 (0xfa00210c): 0x010c -> 0x0104
[CONN_CFG] Configuring Connectivity GPIOs
MUX: setup H19_34XX_GPIO164_OUT (0xfa00219c): 0x0000 -> 0x0004
MUX: setup C27_34XX_CAM_PCLK (0xfa002112): 0x0114 -> 0x011c
MUX: setup AF26_34XX_SYS_NIRQ (0xfa0021e0): 0x0118 -> 0x4118
OMAP DMA hardware revision 5.0
bio: create slab <bio-0> at 0
omap-uart.1: ttyS0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART1
omap-uart.2: ttyS1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART2
omap-uart.3: ttyS2 at MMIO 0x49020000 (irq = 74) is a OMAP UART3
omap-uart.4: ttyS3 at MMIO 0x10000000 (irq = 262) is a OMAP UART4
console [ttyS3] enabled
i2c_omap i2c_omap.1: bus 1 rev4.0 at 100 kHz
twl4030: PIH (irq 7) chaining IRQs 368..375
twl4030: power (irq 373) chaining IRQs 376..383
twl4030: gpio (irq 368) chaining IRQs 384..401
twl4030_mmc_init:367
twl4030_mmc_init:382
twl4030_mmc_init:382
MUX: setup M27_3430_MMC1_CMD (0xfa002146): 0x0118 -> 0x0000
MUX: setup AF10_3430_MMC3_CLK (0xfa0025d8): 0x001b -> 0x011a
MUX: setup AC3_3430_MMC3_CMD (0xfa0021d0): 0x000b -> 0x011b
MUX: setup AE11_3430_MMC3_DAT0 (0xfa0025e4): 0x0103 -> 0x011a
MUX: setup AH9_3430_MMC3_DAT1 (0xfa0025e6): 0x0103 -> 0x011a
MUX: setup AF13_3430_MMC3_DAT2 (0xfa0025e8): 0x0103 -> 0x011a
MUX: setup AE13_3430_MMC3_DAT3 (0xfa0025e2): 0x0103 -> 0x011a
regulator: VMMC1: 1850 <--> 3150 mV normal standby
regulator: VDAC: 1800 mV normal standby
regulator: VUSB1V5: 1500 <--> 0 mV normal standby
regulator: VUSB1V8: 1800 <--> 0 mV normal standby
regulator: VUSB3V1: 3100 <--> 0 mV normal standby
regulator: VPLL2: 1800 mV normal standby
regulator: VMMC2: 1850 mV normal standby
regulator: VSIM: 1800 <--> 3000 mV normal standby
i2c_omap i2c_omap.2: bus 2 rev4.0 at 100 kHz
i2c_omap i2c_omap.3: bus 3 rev4.0 at 400 kHz
SCSI subsystem initialized
Unsupported charging current
twl4030_usb twl4030_usb: Initialized TWL4030 USB module
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Sangoma WANPIPE Router v1.1 (c) 1995-2000 Sangoma Technologies Inc.
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
dspbridge_init: 600000 bytes @ 81000000
zoom2_wifi_init: start
omap-iommu omap-iommu.0: isp registered
NetWinder Floating Point Emulator V0.97 (double precision)
ashmem: initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
yaffs Jul 29 2010 16:39:17 Installing.
msgmni has been set to 1490
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
OMAP DSS rev 2.0
OMAP DISPC rev 3.0
OMAP VENC rev 2
OMAP DSI rev 1.0
brd: module loaded
loop: module loaded
smsc911x: Driver version 2008-10-21.
smsc911x-mdio: probed
eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:01,
irq=-1)
net eth0: MAC Address: 00:08:ee:03:ea:cb
Linux video capture interface: v2.00
omap-previewer omap-previewer: omap-previewer: Registered preview
wrapper
omap3isp omap3isp: Revision 15.0 found
omap-iommu omap-iommu.0: isp: version 1.1
i2c /dev entries driver
DSP Bridge driver loaded
Driver 'sd' needs updating - please use bus_type methods
omap2-nand driver initializing
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xbc (Micron NAND 512MiB
1,8V 16-bit)
Creating 7 MTD partitions on "omap2-nand.0":
0x000000000000-0x000000080000 : "X-Loader-NAND"
0x000000080000-0x000000200000 : "U-Boot-NAND"
0x0000001c0000-0x000000200000 : "Boot Env-NAND"
0x000000200000-0x000001e00000 : "Kernel-NAND"
0x000002000000-0x00000c000000 : "system"
0x00000c000000-0x00000e000000 : "userdata"
0x00000e000000-0x000010000000 : "cache"
android init
android_bind
mass_storage_function_add
android_usb gadget: Number of LUNs=1
adb_function_add
android_usb gadget: android_usb ready
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: MUSB HDRC host driver
usb usb1: Manufacturer: Linux 2.6.29-omap1 musb-hcd
usb usb1: SerialNumber: musb_hdrc
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
input: TWL4030 Keypad as /devices/platform/i2c_omap.1/i2c-adapter/
i2c-1/1-004a/twl4030_keypad/input/input0
synaptics_ts_probe: Product Major Version 1
synaptics_ts_probe: Product Minor Version 5
synaptics_ts_probe: product property 2
synaptics_ts_probe: device control 81
synaptics_ts_probe: interrupt enable 3
synaptics_ts_probe: 0xe0: 1 1 1 2 1 5 0 0
synaptics_ts_probe: Sensor properties 601
synaptics_ts_probe: max_x 7515, max_y 4667
synaptics_ts_probe: inactive_x 0 0, inactive_y 0 0
synaptics_ts_probe: snap_x 0-0 0-0, snap_y 0-0 0-0
input: synaptics-rmi-touchscreen as /devices/virtual/input/input1
synaptics_ts_probe: Start touchscreen synaptics-rmi-touchscreen in
interrupt mode
twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0
Driver for 1-wire Dallas network protocol.
omap_hdq omap_hdq.0: OMAP HDQ Hardware Rev 0.5. Driver in Interrupt
mode
w1_master_driver w1 bus master: Family 1 for 01.000000000000.3d is not
registered.
OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCILL protocol initialized
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
logger: created 64K log 'log_main'
logger: created 256K log 'log_events'
logger: created 64K log 'log_radio'
Advanced Linux Sound Architecture Driver Version 1.0.18a.
No device for DAI twl4030
No device for DAI twl4030 Voice
No device for DAI twl4030 Clock
No device for DAI omap-mcbsp-dai-0
No device for DAI omap-mcbsp-dai-1
No device for DAI omap-mcbsp-dai-2
No device for DAI omap-mcbsp-dai-3
No device for DAI omap-mcbsp-dai-4
Zoom2 SoC init
No device for DAI null
MUX: setup MCBSP4_SLAVE (0xfa00218a): 0x0004 -> 0x0100
MUX: setup MCBSP4_SLAVE (0xfa0020b6): 0x0000 -> 0x0102
MUX: setup MCBSP4_SLAVE (0xfa0020b8): 0x0004 -> 0x0102
MUX: setup MCBSP4_SLAVE (0xfa0020ba): 0x0101 -> 0x0002
TWL4030 Audio Codec init
asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
asoc: twl4030 Voice <-> omap-mcbsp-dai-1 mapping ok
asoc: null <-> omap-mcbsp-dai-1 mapping ok
asoc: null <-> omap-mcbsp-dai-2 mapping ok
ALSA device list:
#0: Zoom2 (twl4030)
oprofile: using timer
nf_conntrack version 0.5.0 (12288 buckets, 49152 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
Bluetooth: L2CAP ver 2.13
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Power Management for TI OMAP3.
pm_dbg_init()
<6>SR: Nvalues not fused for1.2G, disabled
SR1:Fused Nvalues for VDD1OPP4 aaa18f
SR1:Fused Nvalues for VDD1OPP3 aacdaf
SR1:Fused Nvalues for VDD1OPP2 9a86e3
SR1:Fused Nvalues for VDD1OPP1 99ddb8
sr1_opp_margin[1]=37500
sr1_opp_margin[2]=37500
sr1_opp_margin[3]=37500
sr1_opp_margin[4]=62500
steps added, volt will berecaliberated automatically
SR2:Fused Nvalues for VDD2OPP1 10087878
SmartReflex driver initialized
Disabling unused clock "gpt2_ick"
Disabling unused clock "gpio2_dbck"
Disabling unused clock "gpio3_dbck"
Disabling unused clock "gpio5_dbck"
Disabling unused clock "gpt2_fck"
Disabling unused clock "wdt2_ick"
Disabling unused clock "wdt2_fck"
Disabling unused clock "sad2d_ick"
Disabling unused clock "dpll4_m6x2_ck"
Disabling unused clock "dpll4_m5x2_ck"
Disabling unused clock "dpll3_m3x2_ck"
Disabling unused clock "sys_clkout1"
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev
3
sil9022 3-0039: <sil9022_set_cm_clkout_ctrl> sil9022 HDMI Chip version
= b0
Console: switching to colour frame buffer device 100x30
GPIO-199 autorequested
omapdss DPI error: display already enabled
omap_voutDisplay already enabled
omapdss DPI error: display already enabled
omap_voutDisplay already enabled
omap_voutBuffer Size = 1843200
omap_vout: registered and initialized video device 0 [v4l2]
omap_voutBuffer Size = 1843200
omap_vout: registered and initialized video device 1 [v4l2]
omap_voutdisplay->updated
imx046 2-001a: model id detected 0x46 mfr 0xb, rev# 0x2
imx046 2-001a: imx046 chip version 0x02 detected
video4linux video5: video5 is now omap3/imx046//
lv8093 Lens HW detected
video4linux video5: video5 is now omap3/imx046/lv8093/
lv8093 2-0072: Registered lv8093 as V4L2 device.
mmc0: host does not support reading read-only switch. assuming write-
enable.
mmc0: new high speed SD card at address 0002
Registered lv8093 as i2c device.
mmcblk0: mmc0:0002 00000 1.90 GiB
mmcblk0:<6>twl4030_rtc twl4030_rtc: setting system clock to
2000-01-01 01:52:52 UTC (946691572)
p1 p2
Waiting 3sec before mounting root device...
EXT3-fs warning: maximal mount count reached, running e2fsck is
recommended
kjournald starting. Commit interval 5 seconds
EXT3 FS on mmcblk0p2, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) on device 179:2.
Freeing init memory: 200K
Warning: unable to open an initial console.
init: cannot open '/initlogo.rle'
SR1.5 is enabled by default instead of class3
SR1.5 is enabled by default instead of class3
init: cannot find '/system/bin/fw3a_core', disabling 'fw3a'
init: cannot find '/system/bin/playmp3', disabling 'bootsound'
sh: can't access tty; job controCOD_OpenBase: error status 0x8000803d
pszCoffPath: /system/lib/dsp/baseimage.dof
l turned off
# Enabling CTS wakeup for UART1<6>warning: `rild' uses 32-bit
capabilities (legacy support in use)
[ system get stuck here ]

- Thomas

[Michael Malyshev]

I had similar problem.

try to press ENTER several times at uboot prompt -- you should get android shell prompt and then type 'logcat' You'll see log messages from Android. Please post the log here.

BR,
--Michael

[Thomas Ng]

Hi,

The issue was solved. Thanks.

What I did was to apply this patch:  http://elinux.org/Android_on_OMAP#Page_flipping_frame_buffer .

The UI is slow though.

- Thomas

[Michael Malyshev]

yes, but you may try to instal HW open GL. It works much faster.

--Michael

[Thomas Ng]

Thanks Michael.

Do you know of any "getting started" guide on how to install the
openGL for my zoom3 ?
Any URL links step-by-step guide will also be useful.

- Thomas

[Michael Malyshev]

Hi Thomas,

Here si the link to the release notes

http://www.omappedia.org/wiki/L25.INC2.5_Release_Notes

Try steps in "Installing graphics package". It worked for me. You also need to install DSP binaries (described on the same page).

However I could start my board with OpenGL only with uImage provided by TI. I did not play alto with it, but it works much faster. If you you are able to star zoom 3 with your own kernel please let me know

--Michael

[Thomas Ng]

Hi Michael,

thanks for the info.

I am travelling now however, and won't be able to work on this for 1 -2 months.

will update again once I get to work on it.

- Thomas