scsi controller issue
tim
Here's the situation:
Had a mobo go bad on a 4.2 sbs box, PIII 500 Proliant 3000 w/DLT 20/40,
took the three raid 5 drives out, put them in another box, Proliant
1850 w/DAT8 - all is ok. Try to run Veritas Backup Exec 8.5, get
errors that the device driver load was unsucessful - check that drives
are connected, on, aspi compatible controller, aspi manager loaded.
The driver, cpqscsi.ham is loaded, the server has a two channel on
board scsi controller and we are loading nwaspi. Running a config does
show the cpqscsi.ham loaded but not used with the onboard controller -
kinda loaded in space.
Have another 1850 w/Netware 5.0, same onboard controller, same driver
but with a different version (5.0=1.42, 4.2=1.38) and all is ok. Can
my problem be a cpqscsi.ham version issue being that it was one that
was used with the 3000 but can't be used with the 1850? If not, then
what is the deal??? I don't think the onboard controller is the issue
but can't be sure.
Lastly, without loading solitude.dsk, which purports to be some sort of
open file option file from Veritas backupExec, the raid controller
would load but NW would not mount the volume. Any reason why solitude
should have this kind of influence? Can some other file do what
solitude.dsk does?
Any help would be appreciated, Veritas is useless.
Barry Schnur
NW 4x is running increasingly into issues with newer hardware and drivers
-- not quite so much with 'clone' systems since once can configure them
with 'matching' controllers (2940U2W, DC390U2W, that generation)
controllers fairly readily, along with 82557/82558 Intel NIC's.
--
Barry Schnur
Novell Support Connection Volunteer Sysop
tim
and hope?? Is the driver the problem??
Barry Schnur
> and hope?? Is the driver the problem??
It might work -- I haven't worked with Compaqs for a long time. Last 'new
hardware' deploy on a 4.2 server I did was with a Dell PowerEdge using an
embedded 39160 -- which worked fine once I tracked down the right driver
for it.
tim
server.
the diff between the old cpqscsi.ham and new is like months based upon
the compilation date. Just doens't seem like there could be that much
difference to cause it not to work.
triple poops - well, I do have a replacement mobo coming for the downed
3000 - maybe i will just put it in and put the drives back in the orig
server.
Do you think there are other files that would need updating in addition
to the cpqscsi.ham?
Dave Lunn
"tim" <tjdab...@yahoo.com> wrote in message
news:x6mNb.1345$zt3...@prv-forum2.provo.novell.com...
--
Dave Lunn
NSC SysOp
http://support-forums.novell.com
tim
config.txt:
Novell File Server Configuration Report For Server: name changed
Novell File Server Configuration Report Created: Wed, Jan 14, 2004
11:08 am
Novell File Server Configuration Report. [Produced by CONFIG.NLM v2.01]
Novell NetWare 4.11 August 22, 1996
(C) Copyright 1983-1996 Novell Inc. All Rights Reserved.
Server name...............: name changed
OS Version................: v4.11
OS revision number........: 0
Server Up Time(D:H:M:Sec).: 0:01:11:28
Internal Net. Addr........: 3819E1BBh
Security Restriction Level: 1
SFT Level.................: 2
Engine Type...............: NATIVE
TTS Level.................: 1
Total Server memory.......: 255.62 MB or 268040192 Bytes
Processor speed rating....: 41067
Original cache buffers....: 64908
Current Cache Buffers.....: 54905
LRU Sitting Time(D:H:M:S).: 0:01:09:22
Current FSP's.............: 7
Current Receive Buffers...: 50
Directory cache buffers...: 77
Workstations Connected....: 48
Max Workstations Connected: 49
Server language...........: ENGLISH (4)
*********************************************************************
Top of Patch List
---------------------------------------------------------------------
Patch Kit Information:
Description: OS Patch Kit for NetWare v4.11 and v4.2 (990625)
Source: C:\NWSERVER\PK411.NLM
Version: v7.10 (06/25/99)
Status: All PK patches currently loaded/active
Total Patches: 74
# Patches Loaded: 74
PK Patches:
ABENDDIS.NLM v1.00 (08/19/98) Status: ACTIVE
ACTMDLFX.NLM v1.00 (09/23/96) Status: ACTIVE
ADDFILFX.NLM v1.00 (07/30/97) Status: ACTIVE
AUDALTFX.NLM v1.00 (07/08/97) Status: ACTIVE
AUDCLRFX.NLM v1.02 (05/08/97) Status: ACTIVE
AUDCONFX.NLM v1.00 (10/02/96) Status: ACTIVE
AUDDELFX.NLM v1.00 (10/02/96) Status: ACTIVE
AUDEV2FX.NLM v1.01 (03/04/98) Status: ACTIVE
AUDEVTFX.NLM v1.00 (04/01/97) Status: ACTIVE
AUDOVFFX.NLM v1.00 (10/02/96) Status: ACTIVE
AUDRESFX.NLM v1.00 (11/11/96) Status: ACTIVE
BRDAUDFX.NLM v1.01 (08/18/98) Status: ACTIVE
CACHEPER.NLM v1.01 (02/03/98) Status: ACTIVE
CLSFILFX.NLM v1.02 (07/31/98) Status: ACTIVE
COMUSEFX.NLM v1.00 (06/24/99) Status: ACTIVE
CRYSYMFX.NLM v1.00 (01/28/99) Status: ACTIVE
DATSTRFX.NLM v1.01 (10/10/97) Status: ACTIVE
DBGACTEV.NLM v1.00 (10/26/98) Status: ACTIVE
DBGCLNFX.NLM v1.00 (04/08/97) Status: ACTIVE
DFSCCHFX.NLM v1.00 (09/23/96) Status: ACTIVE
DFSSETFX.NLM v1.00 (09/23/96) Status: ACTIVE
DIFTIMFX.NLM v1.00 (03/06/97) Status: ACTIVE
EXPRTSYM.NLM v1.05 (09/14/98) Status: ACTIVE
FATFREFX.NLM v1.00 (12/05/97) Status: ACTIVE
GARHIGFX.NLM v1.00 (03/06/97) Status: ACTIVE
GENDHLFX.NLM v1.00 (04/08/97) Status: ACTIVE
GETFILCN.NLM v1.00 (10/14/98) Status: ACTIVE
GETLANFX.NLM v1.00 (02/03/98) Status: ACTIVE
GETNSIFX.NLM v1.00 (12/17/96) Status: ACTIVE
HOTPLGFX.NLM v1.00 (02/07/97) Status: ACTIVE
LCKRETFX.NLM v1.01 (07/08/97) Status: ACTIVE
LCKWAKFX.NLM v1.00 (08/19/98) Status: ACTIVE
LGFLSTFX.NLM v1.00 (03/06/97) Status: ACTIVE
LOCKPERF.NLM v1.02 (05/21/98) Status: ACTIVE
LOGCNCFX.NLM v1.00 (04/23/98) Status: ACTIVE
LSLPRMFX.NLM v1.00 (08/27/97) Status: ACTIVE
MACCONFX.NLM v1.00 (10/02/96) Status: ACTIVE
MEVCLRFX.NLM v1.00 (04/01/97) Status: ACTIVE
MIGPRGFX.NLM v1.00 (09/23/96) Status: ACTIVE
MKTHRCLB.NLM v1.00 (12/05/97) Status: ACTIVE
MMPARTFX.NLM v1.00 (02/17/99) Status: ACTIVE
MMRESYFX.NLM v1.00 (10/26/98) Status: ACTIVE
MMSPECFX.NLM v1.01 (10/10/97) Status: ACTIVE
MOVMEMFX.NLM v1.00 (02/27/98) Status: ACTIVE
NCPSIZFX.NLM v1.00 (01/28/99) Status: ACTIVE
NETGSPFX.NLM v1.00 (12/17/96) Status: ACTIVE
NSFILCFX.NLM v1.00 (01/28/99) Status: ACTIVE
NWALRTFX.NLM v1.00 (05/12/99) Status: ACTIVE
OCSHARFX.NLM v1.00 (08/19/98) Status: ACTIVE
OCTOUTFX.NLM v1.00 (08/19/98) Status: ACTIVE
OPLMSGFX.NLM v1.00 (07/08/97) Status: ACTIVE
OPNSIZFX.NLM v1.02 (08/27/97) Status: ACTIVE
PRGFREFX.NLM v1.00 (03/06/97) Status: ACTIVE
QMSDISFX.NLM v1.01 (02/13/98) Status: ACTIVE
READGIFX.NLM v1.00 (04/07/98) Status: ACTIVE
REAHEAFX.NLM v1.00 (01/28/99) Status: ACTIVE
RECALCFX.NLM v1.01 (04/08/97) Status: ACTIVE
REGSCRFX.NLM v1.00 (03/06/97) Status: ACTIVE
RENENTFX.NLM v1.00 (10/02/96) Status: ACTIVE
REVFHRFX.NLM v1.00 (05/12/99) Status: ACTIVE
RTTRSTFX.NLM v1.00 (01/06/98) Status: ACTIVE
SCANBIND.NLM v1.00 (10/14/98) Status: ACTIVE
SCRCHGFX.NLM v1.00 (03/06/97) Status: ACTIVE
SCRSWIFX.NLM v1.00 (05/12/99) Status: ACTIVE
SIGPCKFX.NLM v1.00 (04/08/97) Status: ACTIVE
SPXACKFX.NLM v1.10 (02/22/99) Status: ACTIVE
STDIRHFX.NLM v1.00 (09/23/96) Status: ACTIVE
STRSUBFX.NLM v1.00 (02/27/98) Status: ACTIVE
SUBFREFX.NLM v1.01 (04/23/98) Status: ACTIVE
SUBRMVFX.NLM v1.00 (04/08/97) Status: ACTIVE
SUBSECFX.NLM v1.00 (02/27/98) Status: ACTIVE
TTSTHROT.NLM v1.00 (10/14/98) Status: ACTIVE
VMUPDRFX.NLM v1.00 (08/27/97) Status: ACTIVE
VOLDISFX.NLM v1.00 (04/07/98) Status: ACTIVE
Discrete Patches:
None
Hardware Loader ID:
00000021 (Novell loader, rev 1)
---------------------------------------------------------------------
End of Patch List
*********************************************************************
*********************************************************************
Top of Modules List 87 Modules Loaded.
---------------------------------------------------------------------
AD_ASPI.NLM v7.50 Feb. 21, 2002 Backup Exec ASPI Device Driver for
NetWare
(c) 1999 VERITAS Software Corporation. All rights reserved.
AFREECON.NLM v4.00e Aug. 14, 2003 AdRem Free Remote Console (NCPE)
(C) Copyright 2001-2003 AdRem Software, Inc. All Rights Reserved
AFTER311.NLM v4.10a Oct. 21, 1994 NetWare 3.11 Compatible NLM Support
Module
(c) Copyright 1992-1994, Novell, Inc. All rights reserved.
AIO.NLM v6.04 Jun. 2, 1997 NetWare Asynchronous I/O Library
IP0200.G01
Copyright (c) 1991-1997 Novell, Inc. All rights reserved.
AIOCOMX.NLM v2.13 Jan. 13, 1995 Novell AIO Serial COM Port Driver
(v2.13, 12 Jan 1995)
Copyright 1994 Novell, Inc. All rights reserved.
BECLIENT.NLM v8.50 Jun. 30, 2000 Backup Exec - NetWare Client
(c) 1999 VERITAS Software Corporation. All rights reserved.
BEMGR.NLM v8.50 Sep. 7, 2000 Backup Exec - Job Manager
(c) 1999 VERITAS Software Corporation. All rights reserved.
BEPSVR.NLM v8.50 Mar. 19, 2002 Backup Exec - NCPE Server
(c) 1999 VERITAS Software Corporation. All rights reserved.
BESRVR.NLM v8.50 Mar. 18, 2002 Backup Exec - Job Server
(c) 1999 VERITAS Software Corporation. All rights reserved.
BKUPEXEC.NLM v8.50 Jan. 29, 2001 Backup Exec SureStart
(c) 1999 VERITAS Software Corporation. All rights reserved.
BTRIEVE.NLM v6.15 May. 21, 1996 BTRIEVE.NLM v6.15.430 (Unlimited
Users)
CALNLM32.NLM v5.02e Aug. 28, 1998 NetWare NWCalls Runtime Library
(C) Copyright 1995-1998, Novell, Inc. All rights reserved.
Patent Pending--Novell, Inc.
CLIB.NLM v4.11o Oct. 2, 1998 Novell Standard C Library for NLMs
Copyright (c) 1998 Novell, Inc. All rights reserved.
CLNNLM32.NLM v5.02e Aug. 28, 1998 NetWare NWClient Runtime Library
(C) Copyright 1995-1998, Novell, Inc. All rights reserved.
Patent Pending--Novell, Inc.
CLXNLM32.NLM v5.02e Aug. 28, 1998 NetWare NWCLX Runtime Library
(C) Copyright 1995-1998, Novell, Inc. All rights reserved.
Patent Pending--Novell, Inc.
CMPSUPER.NLM v1.01 Jun. 3, 1997 Compression Subsystem Supervisor
IP0200.G01
Copyright 1994-1995 Novell, Inc. All rights reserved.
CONFIG.NLM v2.01 Nov. 1, 1999 NetWare Server Configuration Reader
(C) Copyright Novell, Inc. 1993-1999
CONLOG.NLM v1.03 Feb. 5, 1997 System Console Logger IP0200.B02
(c) Copyright 1992-1996 Novell, Inc. All rights reserved.
CPQARRAY.HAM v1.22 Aug. 6, 1998 Compaq Disk Array Controller Host
Adapter Module
Copyright 1996,1998 Compaq Computer Corporation. All rights reserved.
CPQNF3.LAN v2.45 Mar. 25, 1999 Compaq NetFlex-3 & Netelligent
Ethernet HSM
Copyright 1994,1999 Compaq Computer Corporation. All rights reserved.
CPQSCSI.HAM v1.37 Aug. 5, 1999 Compaq Ultra/Fast/Wide SCSI-2 HAM
v1.37
Copyright 1995,1999 Compaq Computer Corporation. All rights reserved.
CPQSHD.CDM v1.32 Jul. 14, 1999 Compaq NWPA SCSI Disk Driver v1.32
Copyright 1997,1999 Compaq Computer Corporation. All rights reserved.
CPUCHECK.NLM v1.00 Oct. 9, 1997 NetWare Processor Checking Utility
CSL.NLM v2.06b Mar. 6, 1998 NetWare Call Support Layer MOAB_NDK.2
(c) Copyright 1991-1998 Novell, Inc. All Rights Reserved.
CSLIND.NLM v4.20 Jul. 30, 1998 TCPIP CSL INDEPENDENCE MODULE
Copyright 1994-1998 Novell, Inc. All rights reserved.
DIAG411.NLM v1.30 Oct. 9, 1998 Diagnostic/coredump utility for NW
v4.11
(C) Copyright 1998 Novell Inc. All Rights Reserved.
DMGMT.NLM v3.01 Jul. 11, 1997 Device Management NLM IP0200.G05
Copyright (C) 1996,1997 Novell, Inc. All rights reserved.
DS.NLM v6.04 Jun. 1, 1999 NetWare 4.11 Directory Services
Copyright 1993-1998 Novell, Inc. All rights reserved. Patents
Pending.
DSAPI.NLM v5.02e Aug. 28, 1998 NetWare NWNet Runtime Library
(C) Copyright 1995-1998, Novell, Inc. All rights reserved.
Patent Pending--Novell, Inc.
DSEVENT.NLM v5.02e Aug. 28, 1998 NetWare DSEvent Runtime Library
(C) Copyright 1995-1998, Novell, Inc. All rights reserved.
Patent Pending--Novell, Inc.
DSLOADER.NLM v1.48 Jul. 15, 1996 NetWare 4.11 Directory Services
Loader
Copyright 1993-1996 Novell, Inc. All rights reserved. Patents
pending.
ETHERTSM.NLM v3.80 Mar. 1, 1999 Novell Ethernet Topology Specific
Module
(C) Copyright 1990 - 1999, by Novell, Inc. All rights reserved.
FPSM.NLM v4.11o Oct. 7, 1998 NetWare Floating-Point Support
Module
Copyright (c) 1998 Novell, Inc. All rights reserved.
IDEATA.HAM v1.30p Jun. 9, 1999 Novell ATA/IDE/ATAPI Host Adapter
Module
Copyright 1989-1999, Novell, Inc. All rights reserved.
IDECD.CDM v1.31e Oct. 30, 1998 Novell ATAPI CD-ROM/DVD Custom
Device Module
Copyright 1994-1998, Novell, Inc. All rights reserved.
IPXRTR.NLM v6.60 Jun. 24, 1998 IPX NLSP Router
Copyright 1994-1998 Novell, Inc. All rights reserved.
Portions Copyright 1991-1998 D.L.S. Associates.
IPXRTRNM.NLM v6.60 Jun. 24, 1998 IPX Router Network Management
Copyright 1994-1998 Novell, Inc. All rights reserved.
IPXS.NLM v4.10 Oct. 20, 1994 NetWare STREAMS IPX Protocol
(C) Copyright 1989-1994 Novell, Inc.
All Rights Reserved.
LIC_API.NLM v2.02 Sep. 23, 1997 License APIs TURBO.B02
(c) Copyright 1995-97 Novell, Inc. All rights reserved
LOCNLM32.NLM v5.02e Aug. 28, 1998 NetWare NWLocale Runtime Library
(C) Copyright 1995-1998, Novell, Inc. All rights reserved.
Patent Pending--Novell, Inc.
LONG.NAM v4.11d Aug. 10, 1998 Netware Long Filename Name Space
Support
Copyright 1998 Novell, Inc. All rights reserved.
LSAPI.NLM v4.21 Jun. 29, 1999 NLS LSAPI
Copyright 1995-1998 Novell, Inc. All Rights Reserved.
MONITOR.NLM v4.35 May. 23, 1997 NetWare 4.x Console Monitor
(c) Copyright 1989-1996, Novell, Inc. All rights reserved.
MSM.NLM v3.95 May. 12, 1999 Novell Multi-Processor Media Support
Module
Copyright (c) 1990 - 1999, by Novell, Inc. All rights reserved.
NBI.NLM v2.25 Sep. 17, 1998 NetWare Bus Interface
Copyright 1995-1998 Novell, Inc. All rights reserved.
NCPNLM32.NLM v5.02e Aug. 28, 1998 NetWare NWNCP Runtime Library
(C) Copyright 1995-1998, Novell, Inc. All rights reserved.
Patent Pending--Novell, Inc.
NEB.NLM v1.01 Aug. 28, 1998 Novell Event Bus
Copyright 1998 Novell, Inc. All rights reserved.
NETDB.NLM v4.08 Jun. 25, 1999 NETWORK DATABASE ACCESS NLM
(C) Copyright 1998, Novell, Inc. All rights reserved
NETNLM32.NLM v5.02e Aug. 28, 1998 NetWare NWNet Runtime Library
(C) Copyright 1995-1998, Novell, Inc. All rights reserved.
Patent Pending--Novell, Inc.
NIT.NLM v4.11o Oct. 7, 1998 NetWare Interface Tools (NIT)
Library
Copyright (c) 1998 Novell, Inc. All rights reserved.
NLMLIB.NLM v4.11o Oct. 7, 1998 NetWare NLM Runtime Library
Copyright (c) 1998 Novell, Inc. All rights reserved.
NLSAPI.NLM v4.21 Jun. 29, 1999 NLSAPI
Copyright 1996-1998 Novell, Inc. All Rights Reserved.
NLSLSP.NLM v4.21 Jul. 16, 1999 NLS License Service Provider
Copyright 1996-1998 Novell, Inc. All Rights Reserved.
NLZS.NLM v1.01 Jun. 3, 1997 Novell - Stac LZS Compression Driver
IP0200.G01
Copyright 1994-1996 Novell, Inc. All rights reserved.
NRLTLI.NLM v8.50 Aug. 11, 2000 Backup Exec - Remote Workstation
Backup Software
(c) 1999 VERITAS Software Corporation. All rights reserved.
NWASPI.CDM v2.00 May. 14, 1998 Novell 4.10/4.01/4.02/3.12 ASPI CDM
Copyright 1991-96, Novell, Inc. All rights reserved.
NWPA.NLM v2.36 Oct. 5, 1999 NetWare 3.12/4.x NetWare Peripheral
Architecture NLM : NBI Aware.
Copyright 1991-1999, Novell, Inc. All rights reserved.
NWSNUT.NLM v4.16 Jul. 1, 1996 NetWare NLM Utility User Interface
(c) Copyright 1989-1996, Novell, Inc. All rights reserved.
PKSTUB.NLM v7.10 Jun. 25, 1999 OS Patch Kit for NetWare v4.11 and
v4.2 (990625) [PKS=ALL]
Copyright 1999 Novell, Inc. All rights reserved.
PM411.NLM v1.45 Jun. 25, 1999 Patch Manager for NetWare v4.11
(990625)
Copyright 1999 Novell, Inc. All rights reserved.
PMSTUB.NLM v1.15 Jun. 25, 1999 OS Patch Manager API Stub (990625)
Copyright 1999 Novell, Inc. All rights reserved.
PPPTSM.NLM v3.30a Jul. 27, 1998 PPP TSM MOAB.NDK5
Copyright (c) 1991-1998, Novell, Inc. All Rights Reserved.
PRED.NLM v1.01 Jun. 3, 1997 Predictor Compression Driver
IP0200.G01
Copyright 1994-1996 Novell, Inc. All rights reserved.
REMOTE.NLM v4.10 Jul. 2, 1996 NetWare 4.1 Remote Console
Copyright 1996 Novell, Inc. All rights reserved.
REQUESTR.NLM v4.11o Oct. 7, 1998 NetWare NLM Requester Package
Copyright (c) 1998 Novell, Inc. All rights reserved.
ROLLCALL.NLM v4.10 Jun. 9, 1997 RollCall NLM (100, API 1.0)
Copyright 1996 Novell, Inc. All rights reserved.
RSPX.NLM v4.11b Oct. 27, 1997 NetWare Remote Console SPX Driver
Copyright 1997 Novell, Inc. All rights reserved.
SMDR.NLM v4.10a Jun. 18, 1999 NetWare SMS Data Requestor
(C) Copyright 1991-1996 Novell, Inc. All Rights Reserved.
SNMP.NLM v4.10 Mar. 24, 1998 Novell SNMP Agent Module
Copyright 1994-1998 Novell, Inc. All rights reserved.
SOLITUDE.DSK v2.03a Sep. 3, 1999 Solitude
(C) Copyright 1995-99, Vinca Corporation. All rights reserved.
SPOOFER.NLM v1.00 Jun. 2, 1997 SPOOFER IP0200.G01
Copyright(c) 1996-1997 Novell, Inc. All Rights Reserved.
SPXS.NLM v5.13a Feb. 22, 1999 NetWare SPX/SPXII Protocol (PTF)
Copyright 1992-1999 Novell, Inc. All Rights Reserved.
STREAMS.NLM v4.20 May. 24, 1999 NetWare STREAMS PTF
Copyright 1989-1992 Mentat, Inc. All rights reserved.
Portions Copyright 1989-1999 Novell, Inc. All rights reserved.
TCPIP.NLM v5.21a Jul. 1, 1999 Novell TCP/IP Module NW5SP3.240699
Copyright 1994-1999 Novell, Inc. All rights reserved.
THREADS.NLM v4.11o Oct. 7, 1998 NetWare NLM Threads Package
Copyright (c) 1998 Novell, Inc. All rights reserved.
TIMESYNC.NLM v4.15 Jul. 8, 1996 Netware Time Synchronization Services
(C) Copyright 1991-96, Novell, Inc. All rights reserved.
TLI.NLM v4.10a Jan. 30, 1995 NetWare Transport Level Interface
Library
(C) Copyright 1989-1992 Mentat, Inc.
Portions (C) Copyright 1989-1994 Novell, Inc.
All Rights Reserved.
TNRLSPX.NLM v8.50 Aug. 11, 2000 Backup Exec - Peer SPX Support
(c) 1999 VERITAS Software Corporation. All rights reserved.
TOOLBOX.NLM v1.09d Aug. 20, 1998 toolbox.nlm
Utility Toolbox for NetWare 3.12, 4.x
Copyright (c) 1997,1998 Novell Inc.
TSA410.NLM v4.16 Jun. 24, 1999 NetWare 4.10 Target Service Agent
(C) Copyright 1990-1998 Novell, Inc. All rights reserved.
TSANDS.NLM v4.14 Mar. 11, 1998 NetWare Directory Target Service
Agent v4.14
Copyright 1992-1997 Novell, Inc. All rights reserved.
UNICODE.NLM v4.10 Jul. 8, 1996 NetWare Unicode Library NLM
Copyright 1996 Novell, Inc. All rights reserved.
UNI_850.NLM v1.01 Apr. 2, 1998 NetWare Unicode conversion API for
code page 850, V1.01
UNI_MON.NLM v1.01 Apr. 2, 1998 NetWare Unicode Lower Case API, V1.01
UNI_UPR.NLM v1.01 Apr. 2, 1998 NetWare Unicode Upper Case API, V1.01
WHSMAIO.LAN v3.02a Jun. 23, 1997 WHSMAIO Driver IP0200.G03
(C) Copyright 1992-1996 Novell, Inc. All Rights Reserved.
WSM.NLM v3.02 Jun. 2, 1997 WAN Support Module IP0200.G01
(C) Copyright 1993-1997 Novell, Inc. All Rights Reserved.
---------------------------------------------------------------------
End of Modules List 87 Modules Loaded.
*********************************************************************
*********************************************************************
Top of LAN Driver Configuration Listing
---------------------------------------------------------------------
Signature.....: HardwareDriverMLID
CFG Version...: 1.12
Node Address..: 00013819E1BB
Board Number..: 1
Board Instance: 1
Media Type....: PPP
MLID Version..: 3.02
Slot..........: 255
I/O...........: None
Memory........: None
IRQ...........: None
DMA...........: None
Logical Name..: COMPORT_1
Signature.....: HardwareDriverMLID
CFG Version...: 1.14
Node Address..: 00508B91A206
Board Number..: 2
Board Instance: 1
Media Type....: ETHERNET_802.2
MLID Version..: 2.45
Slot..........: 10010
I/O...........: 2C00h -> 2C0Fh
Memory........: None
IRQ...........: 15
DMA...........: None
Logical Name..: CPQNF3_1_E82
Signature.....: HardwareDriverMLID
CFG Version...: 1.14
Node Address..: 00508B91A206
Board Number..: 3
Board Instance: 1
Media Type....: ETHERNET_II
MLID Version..: 2.45
Slot..........: 10010
I/O...........: 2C00h -> 2C0Fh
Memory........: None
IRQ...........: 15
DMA...........: None
Logical Name..: CPQNF3_1_EII
---------------------------------------------------------------------
End of LAN Driver Configuration Listing
*********************************************************************
************************************************
******Disk Drive Configuration Information******
------------------------------------------------
[V025-A2-D1:0] COMPAQ CD-224E rev:9.0B
Card 0 Controller 1 Drive 0
Device Type.................: CDROM
Read After Write Verify.....: Not Supported
Drive Operating Status......: Inactive
Removable Drive Mount Status: Not Mounted
Removable Drive Lock Status.: Not Locked
Driver......................: IDEATA.HAM
Int.........................: 14
IO Ports....................: 0x1f0 -> 0x1f8
Partitions..................: 0
[V503-A1-D0:0] Compaq SMART-2 Slot 2 Disk 1 DDG
Card 0 Controller 0 Drive 0
Volume Segments on Drive:
Device Type.................: DISK
Read After Write Verify.....: Not Supported
Drive Operating Status......: Active
Driver......................: CPQARRAY.HAM
Slot........................: 2
Int.........................: 10
MEMORY1.....................: c6ffff00 -> c7000000
IO Ports....................: 0x3000 -> 0x3100
Drive Size..................: 17351 Megabytes
Partitions..................: 3
Device # 2 Filter for #01 [V503-A1-D0:0] C (77000100)
Card 0 Controller 0 Drive 1
Volume Segments on Drive:
17057 Megabytes on Volume SYS segment 0
Device Type.................: DISK
Read After Write Verify.....: Disabled
Drive Operating Status......: Active
Driver......................: SOLITUDE.DSK
Drive Size..................: 17351 Megabytes
Partitions..................: 3
Mirror Status...............: Not Mirrored
Partition Blocks............: 4368660
Data Blocks.................: 4366854
Redirection Blocks..........: 1806
Redirected Blocks...........: 0
Reserved Blocks.............: 28
***********************************************
* Volume Statistics for SYS *
***********************************************
Volume Size................: 17057 MBytes
Block Size.................: 64 KB
Total Blocks...............: 272927
Free Blocks................: 149036
Purgable Blocks............: 10564
Not Yet Purgable Blocks....: 1
Total Directory Entries....: 1080832
Available Directory Entries: 930336
Sectors per Block..........: 128
Free Disk Space............: 9314 MBytes
Purgable Disk Space........: 660 MBytes
Suballocation..............: ON
Compression................: ON
Migration..................: OFF
***************************************************
Volume Name Name Spaces Loaded
----------------- --------------------------------
SYS DOS
SYS LONG_NAMES
*********************************************************************
Top of file. [SYS:SYSTEM\ABEND.LOG]
---------------------------------------------------------------------
<<ERROR: Cannot open file.>>
---------------------------------------------------------------------
End of file. [SYS:SYSTEM\ABEND.LOG]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\TIMESYNC.CFG]
---------------------------------------------------------------------
# Configuration Parameters from server name changed
Configured Sources = OFF
Directory Tree Mode = ON
Hardware Clock = ON
Polling Count = 3
Polling Interval = 600
Service Advertising = ON
Synchronization Radius = 2000
Type = SINGLE
# Configured time source list from server BAART_ADMIN
---------------------------------------------------------------------
End of file. [SYS:SYSTEM\TIMESYNC.CFG]
*********************************************************************
*********************************************************************
Top of file. [SYS:ETC\NETINFO.CFG]
---------------------------------------------------------------------
#!VERSION=2.3
#!
#! --- WARNING -- WARNING -- WARNING -- WARNING -- WARNING -- WARNING
----
#! This file was created by the Internetworking Configuration Console.
#! It is intended to be modified ONLY by the configurator (INETCFG.NLM).
#! Tampering with this file may cause severe malfunctioning of the
system.
#! The configurator will check for tampering and abort if it is
detected.
#!
-----------------------------------------------------------------------
#!
#!SERVERTYPE=NORMAL
#!
#!UIMODE=NORMAL
#!
#!BEGINGENLOAD
LOAD SNMP
LOAD BCALLSRV
#!END
#!
#!BEGINTSMLOAD
LOAD PPPTSM
#!END
#!
#!BEGINBOARD DRVR=WHSMAIO NAME=COMPORT STATUS=ENABLED NUMPORTS=1
DRVRTYPE=CSL VARIABLEPORTS=YES PORTPARAM=N
#
#!BEGINEXTRA
LOAD AIOCOMX PORT=3F8 INT=4 NAME=COMPORT
#
#!END
#!BEGINPORT NAME=COMPORT_1 NUMBER=1 STATUS=ENABLED FRAMES=NO NUMLINKS=1
MEDIA=PPPTSM WANFRAME=PPP SEQ=18
#!PORTNLM=WHSMAIO CHANNEL=1 AIONAME=COMPORT AIOPORT=1
#
LOAD WHSMAIO NAME=COMPORT_1 N=1 CHANNEL=1 AIONAME=COMPORT AIOPORT=1
SEQ=18
#!END
#!END
#!
#!BEGINBOARD DRVR=N100 NAME=N100_1_E82 STATUS=ENABLED NUMPORTS=1
DRVRTYPE=LAN VARIABLEPORTS=NO PORTPARAM=CHANNEL SLOT=4 SPEED=0
FORCEDUPLEX=0 IOMAPMODE=0 RXINTDELAY=1536
#
#!BEGINPORT NAME=N100_1_E82 NUMBER=1 STATUS=ENABLED FRAMES=YES
NUMLINKS=0 MEDIA=EtherTsm WANFRAME=UNCONFIGURED
#
#!REFCOUNT=1
LOAD N100 NAME=N100_1_E82_EII FRAME=Ethernet_II SLOT=4 SPEED=0
FORCEDUPLEX=0 IOMAPMODE=0 RXINTDELAY=1536
#!REFCOUNT=1
LOAD N100 NAME=N100_1_E82_E82 FRAME=Ethernet_802.2 SLOT=4 SPEED=0
FORCEDUPLEX=0 IOMAPMODE=0 RXINTDELAY=1536
#!END
#!END
#!
#!BEGINBOARD DRVR=CPQNF3 NAME=CPQNF3_1 STATUS=ENABLED NUMPORTS=1
DRVRTYPE=LAN VARIABLEPORTS=NO PORTPARAM=CHANNEL SLOT=10010 PAIR=1
#added after transfer from old server
#!BEGINPORT NAME=CPQNF3_1 NUMBER=1 STATUS=ENABLED FRAMES=YES NUMLINKS=0
MEDIA=EtherTsm WANFRAME=UNCONFIGURED
#
#!REFCOUNT=1
LOAD CPQNF3 NAME=CPQNF3_1_E82 FRAME=Ethernet_802.2 SLOT=10010 PAIR=1
#!REFCOUNT=1
LOAD CPQNF3 NAME=CPQNF3_1_EII FRAME=Ethernet_II SLOT=10010 PAIR=1
#!END
#!END
#!
#!BEGINPROTO PROTO=TCPIP STATUS=ENABLED
LOAD Tcpip RIP=Yes Static=No LoadSharing=No Forward=Yes
#
#!BEGINBIND STATUS=ENABLED
BIND IP N100_1_E82_EII ARP=Yes Mask=255.255.255.0 Address=10.10.20.224
#10.10.20.224
#!END
#!BEGINBIND STATUS=ENABLED
BIND IP CPQNF3_1_EII ARP=Yes Mask=255.255.255.0 Address=10.10.10.224
#10.10.10.224
#!END
#!END
#!
#!BEGINPROTO PROTO=IPX STATUS=ENABLED
SET Reply To Get Nearest Server=ON
#
LOAD IPXRTR ROUTING=RIPSAP CFGDIR=SYS:ETC SEQ=1
#
LOAD IPXRTRNM SEQ=1
#
LOAD SPXCONFG Q=1 A=540 V=54 W=108 R=10 S=1000 I=1200
#
SET IPX NetBIOS Replication Option=1
#
SET Load Balance Local LAN=OFF
#
#!BEGINBIND STATUS=ENABLED
BIND IPX N100_1_E82_E82 net=1000000A seq=3
#1000000A
#!END
#!BEGINBIND STATUS=ENABLED
BIND IPX CPQNF3_1_E82 net=0000000A seq=1
#0000000A
#!END
#!END
#!
#!BEGINREMOTE
LOAD REMOTE ZARDOZZ
LOAD RSPX
#!END
---------------------------------------------------------------------
End of file. [SYS:ETC\NETINFO.CFG]
*********************************************************************
*********************************************************************
Top of file. [SYS:ETC\HOSTS]
---------------------------------------------------------------------
#
# SYS:ETC\HOSTS
#
# Mappings of host names and host aliases to IP address.
#
127.0.0.1 loopback lb localhost # normal loopback address
#
# examples from Novell network
#
130.57.4.2 ta tahiti ta.novell.com loghost
130.57.6.40 osd-frog frog
130.57.6.144 sj-in5 in5
192.67.172.71 sj-in1 in1
#
# interesting addresses on the Internet
#
192.67.67.20 sri-nic.arpa nic.ddn.mil nic
26.2.0.74 wsmr-simtel20.army.mil simtel20
192.168.0.1 BAART_ADMIN
---------------------------------------------------------------------
End of file. [SYS:ETC\HOSTS]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\AUTOEXEC.NCF]
---------------------------------------------------------------------
SET TIME ZONE = PST8PDT
SET DAYLIGHT SAVINGS TIME OFFSET = 1:00:00
SET START OF DAYLIGHT SAVINGS TIME = (APRIL SUNDAY FIRST 2:00:00 AM)
SET END OF DAYLIGHT SAVINGS TIME = (OCTOBER SUNDAY LAST 2:00:00 AM)
SET DEFAULT TIME SERVER TYPE = SINGLE
# NOTE: THE TIME ZONE INFORMATION MENTIONED ABOVE
# SHOULD ALWAYS PRECEDE THE SERVER NAME.
SET BINDERY CONTEXT = O=BAART
FILE SERVER NAME BAART_ADMIN
IPX INTERNAL NET 3819E1BB
MOUNT ALL
SET MAXIMUM FILE LOCKS PER CONNECTION=750
SET MAXIMUM RECORD LOCKS PER CONNECTION=5000
SET UPGRADE LOW PRIORITY THREADS = ON
load conlog maximum=100
; Network driver LOADs and BINDs are initiated via
; INITSYS.NCF. The actual LOAD and BIND commands
; are contained in INITSYS.NCF and NETINFO.CFG.
; These files are in SYS:ETC.
sys:etc\initsys.ncf
#LOAD IPXRTR ROUTING=NLSP
#LOAD TCPIP RIP=YES STATIC=NO LOADSHARING=NO FORWARD=YES
#LOAD N100 SLOT=7 FRAME=ETHERNET_II NAME=N100_1_EII
#BIND IP N100_1_EII ARP=YES MASK=FF.FF.FF.00 ADDRESS=10.10.10.224
#LOAD N100 SLOT=7 FRAME=ETHERNET_802.2 NAME=N100_1_E82
#BIND IPX N100_1_E82 NET=A
# MOUNT ALL
rem LOAD DHCPSRVR
LOAD SYS:\SYSTEM\NAVNLM\NAV.NLM
NSSTART
# THIS COMMAND LOADS BACKUP EXEC FOR NETWARE.
#
#LOAD NWASPI
#BESTART.NCF
REM SET UPGRADE LOW PRIORITY THREADS = ON
LOAD TOOLBOX
Load AFREECON.NLM
#
#
# This command loads Backup Exec for NetWare.
#
#BESTART.NCF------------------------------------------------------------
---------
End of file. [SYS:SYSTEM\AUTOEXEC.NCF]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\BESTART.NCF]
---------------------------------------------------------------------
SEARCH ADD SYS:BKUPEXEC\NLMS\
LOAD BKUPEXEC.NLM -tl -aa -dn -tc -s
---------------------------------------------------------------------
End of file. [SYS:SYSTEM\BESTART.NCF]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\BESTOP.NCF]
---------------------------------------------------------------------
UNLOAD BESRVR
UNLOAD AD_ASPI
UNLOAD BEEXVIEW
UNLOAD BEENABLE
UNLOAD BEOPRD
UNLOAD BPSRV
UNLOAD BPCD
UNLOAD BEORANW
UNLOAD OTMLAPI
UNLOAD OTMCDM.CDM
UNLOAD PMTHREAD
UNLOAD BEEARP
UNLOAD BEPSVR
UNLOAD NRLTLI
UNLOAD
BKUPEXEC.NLM------------------------------------------------------------
---------
End of file. [SYS:SYSTEM\BESTOP.NCF]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\BSTART.NCF]
---------------------------------------------------------------------
;Solomon IV 100-User SQL Installation
LOAD BTRIEVE -p=4096 -f=500 -h=1000 -l=1000 -t=75 -u=0 -s=400 -m=4096
LOAD BSPXCOM -d=10240 -s=200 -w=5
---------------------------------------------------------------------
End of file. [SYS:SYSTEM\BSTART.NCF]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\BSTOP.NCF]
---------------------------------------------------------------------
UNLOAD BROUTER
UNLOAD BSPXCOM
UNLOAD BTRIEVE
---------------------------------------------------------------------
End of file. [SYS:SYSTEM\BSTOP.NCF]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\DGNCMRL.NCF]
---------------------------------------------------------------------
# dgncmrl.ncf [Version 1.00]
# Batch file to unload and reload the Digi Netware CAPI driver
# DGNCMDRV.NLM. WHSMCAPI.LAN is unloaded so that reinitialize
# system will reload WHSMCAPI.LAN for each interface and cause
# it to regegister with DGNCMDRV.NLM
#
unload dgncmdrv
load dgncmdrv
unload whsmcapi
reinitialize system
---------------------------------------------------------------------
End of file. [SYS:SYSTEM\DGNCMRL.NCF]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\DGNCMVER.NCF]
---------------------------------------------------------------------
#
# NCF file to display NCM Driver component versions.
# Copyright (C) 1995-97, Digi International, Inc.
#
load verdump sys:system/dgncm*.nlm sys:system/adp.bin
---------------------------------------------------------------------
End of file. [SYS:SYSTEM\DGNCMVER.NCF]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\GRPWISE.NCF]
---------------------------------------------------------------------
LOAD GWMTA /home-SYS:\MAIL\GWDOM /noerrormail /nosmp /nosnmp
LOAD GWADA /home-SYS:\MAIL\GWDOM /noerrormail /nondssync /nosmp /nosnmp
LOAD GWPOA /home-SYS:\MAIL\GWDOM\GWPO /noerrormail /nosmp /nosnmp
LOAD GWSBA /home-SYS:\MAIL\GWDOM
SEARCH ADD SYS:\MAIL\GWDOM\WPGATE\GWIA\GWCNVRT
LOAD GWIA @SYS:\MAIL\GWDOM\WPGATE\GWIA\GWIA.CFG
---------------------------------------------------------------------
End of file. [SYS:SYSTEM\GRPWISE.NCF]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\LDAFREEC.NCF]
---------------------------------------------------------------------
Load AFREECON.NLM
---------------------------------------------------------------------
End of file. [SYS:SYSTEM\LDAFREEC.NCF]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\NMA2.NCF]
---------------------------------------------------------------------
#
# NMA2.NCF - Loads NetWare Management Agent (NMA) v2.6 NLMs
#
# There is a matching unload file, Unnma2.NCF, that will
# unload the NetWare Management Agent v2.6 NLMs.
#
---------------------------------------------------------------------
End of file. [SYS:SYSTEM\NMA2.NCF]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\NWCRPAIR.NCF]
---------------------------------------------------------------------
nwcstop
load nwcclean sys:\system\nwcrsrc.btr
load butil -clone sys:\system\nwcrsrc.btr sys:\system\nwcrsrc.bad
pause
load butil -recover sys:\system\nwcrsrc.bad sys:\system\nwcrsrc.rcv
pause
load butil -load sys:\system\nwcrsrc.rcv sys:\system\nwcrsrc.btr
pause
load nwcclean sys:\system\nwcrgrp.btr
load butil -clone sys:\system\nwcrgrp.btr sys:\system\nwcrgrp.bad
pause
load butil -recover sys:\system\nwcrgrp.bad sys:\system\nwcrgrp.rcv
pause
load butil -load sys:\system\nwcrgrp.rcv sys:\system\nwcrgrp.btr
pause
load nwcclean sys:\system\nwcmem.btr
load butil -clone sys:\system\nwcmem.btr sys:\system\nwcmem.bad
pause
load butil -recover sys:\system\nwcmem.bad sys:\system\nwcmem.rcv
pause
load butil -load sys:\system\nwcmem.rcv sys:\system\nwcmem.btr
pause
load nwcclean sys:\system\nwcuacl.btr
load butil -clone sys:\system\nwcuacl.btr sys:\system\nwcuacl.bad
pause
load butil -recover sys:\system\nwcuacl.bad sys:\system\nwcuacl.rcv
pause
load butil -load sys:\system\nwcuacl.rcv sys:\system\nwcuacl.btr
pause
load nwcclean sys:\system\nwcpacl.btr
load butil -clone sys:\system\nwcpacl.btr sys:\system\nwcpacl.bad
pause
load butil -recover sys:\system\nwcpacl.bad sys:\system\nwcpacl.rcv
pause
load butil -load sys:\system\nwcpacl.rcv sys:\system\nwcpacl.btr
pause
load nwcclean sys:\system\nwcitem.btr
load butil -clone sys:\system\nwcitem.btr sys:\system\nwcitem.bad
pause
load butil -recover sys:\system\nwcitem.bad sys:\system\nwcitem.rcv
pause
load butil -load sys:\system\nwcitem.rcv sys:\system\nwcitem.btr
pause
load nwcclean sys:\system\cslib\csaudit.log
load butil -clone sys:\system\cslib\csaudit.log
sys:\system\cslib\csaudit.bad
pause
load butil -recover sys:\system\cslib\csaudit.bad
sys:\system\cslib\csaudit.rcv
pause
load butil -load sys:\system\cslib\csaudit.rcv
sys:\system\cslib\csaudit.log
pause
load nwcclean sys:\etc\csl.cfg
load butil -clone sys:\etc\csl.cfg sys:\etc\csl.bad
pause
load butil -recover sys:\etc\csl.bad sys:\etc\csl.rcv
pause
load butil -load sys:\etc\csl.rcv sys:\etc\csl.cfg
---------------------------------------------------------------------
End of file. [SYS:SYSTEM\NWCRPAIR.NCF]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\NWCSTART.NCF]
---------------------------------------------------------------------
; Default NWCSTART NCF file if no services are selected
load nwcsu
load nwccon
---------------------------------------------------------------------
End of file. [SYS:SYSTEM\NWCSTART.NCF]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\NWCSTOP.NCF]
---------------------------------------------------------------------
; Default NWCSTOP NCF file if no services are chosen
unload NWCSU
unload OPENNV
unload CSAUDIT
---------------------------------------------------------------------
End of file. [SYS:SYSTEM\NWCSTOP.NCF]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\RESTART.NCF]
---------------------------------------------------------------------
down
restart
server------------------------------------------------------------------
---
End of file. [SYS:SYSTEM\RESTART.NCF]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\SECURE.NCF]
---------------------------------------------------------------------
##########################################################
#
# Version: 1.01
# Date: May 14, 1997
#
# This NetWare script file, SECURE.NCF, is the enhanced
# security options configuration file. It chooses the
# options that are required to run NetWare in the trusted
# configuration, which is designed to meet the US Class
# C2 security criteria and the European Class F-C2/E2
# security criteria.
#
# Enhanced security options not required for the trusted
# configuration (not required by C2 and European Class
# F-C2/E2 standards) are also included in this file but are
# commented out. More information regarding enhanced
# security options may be found in the Enhanced Security
# Server Administration manual.
#
# The server may be configured to automatically execute
# this configuration file during server boot after the
# execution of AUTOEXEC.NCF. This can be done by setting
# the set parameter "Enable SECURE.NCF" to ON. This can
# be done from SERVMAN (Server parameters/Miscellaneous
# menu) or in either AUTOEXEC.NCF or STARTUP.NCF. This
# configuration file can also be executed from the NetWare
# Console command line.
#
# Each of the SET parameters in this file (SECURE.NCF) can
# be set individually from the NetWare console command line,
# from SERVMAN, or in AUTOEXEC.NCF.
#
# SECURE.NCF may be modified using EDIT.NLM or another
# ASCII editor. The file is stored in the SYS:/SYSTEM
# directory.
#
# The following commands are required for the trusted
# configuration. Refer to the Utilities Reference manual
# for more information about each of these commands.
#
# The following command configures the server to disallow
# the use of unencrypted passwords. The default value is
# OFF. The trusted configuration value is also OFF.
#
SET Allow Unencrypted Passwords = OFF
#
# The following command configures the server to disallow
# the use of passwords to identify auditors. The default
# value is OFF. The trusted configuration value is also
# OFF.
#
SET Allow Audit Passwords = OFF
#
# The following command configures the server to
# automatically run VREPAIR when a volume fails to mount.
# The default value is ON. The trusted configuration
# value is also ON.
#
SET Automatically Repair Bad Volumes = ON
#
# The following command configures the server to reject
# NCP packets that fail boundary checking. Older client
# utilities may fail if this SET parameter is set to ON.
# The default value is OFF. The trusted configuration
# value is ON.
#
SET Reject NCP Packets with bad lengths = ON
#
# The following command configures the server to disallow
# replication of NetBIOS broadcast packets. The default
# value is 2. The trusted configuration value is 0.
#
SET IPX NetBIOS Replication Option = 0
#
# The following command configures the server to reject
# NCP packets that fail component checking. Older client
# utilities may fail if this set parameter is set to ON.
# The default value is OFF. The trusted configuration
# value is ON.
#
SET Reject NCP Packets with bad components = ON
#
# The following command configures NetWare Directory
# Services to perform access control checks which are
# not backwards compatiable with previous versions of
# NetWare Directory Services. The default value is OFF.
# The trusted configuration value is ON.
#
SET Additional Security Checks = ON
#
# The above commands are required for your server to be
# in the trusted configuration, designed to meet the
# Class C2 criteria and the Class F-C2/E2 criteria.
#
#########################################################
#########################################################
#
# The following commands provide additional enhanced
# security options that are not required to meet the
# Class C2 criteria and the Class F-C2/E2 criteria.
# These have been commented out but may be enabled by
# removing the comment symbol (# ) from the beginning of
# the line. EDIT.NLM or another ASCII editor may be used
# to edit this file. For more information about each of
# these commands refer to the Utilities Reference manual.
#
# The following command configures NetWare Directory
# Services to enforce the checking of the Equivalent To
# Me attribute during authentication. DSREPAIR must be
# used to synchronize the Equivalence attribute and the
# Equivalent To Me attribute if the Check Equivalent to
# Me parameter is set to ON. Setting this parameter to
# ON will also adversely affect the authentication
# performance. The default value is OFF. For enhanced
# security the value may be set to ON.
#
# SET Check Equivalent to Me = ON
#
# The following command configures the server to reject
# NCP packets that are not signed and to sign all reply
# packets. Setting this parameter to 3 will adversely
# affect the communication performance of the server.
# The default value is 1, which signs NCP packets only if
# required by the client. For enhanced security the
# value may be set to 3.
#
# SET NCP Packet Signature Option = 3
#
# The following command secures the NetWare server
# console in the following ways: it removes DOS paths
# from the search path; it allows only NLMs from the
# search path to be loaded; it disallows the setting of
# certain SET parameters; it prevents the server date and
# time from being changed; and it prevents keyboard entry
# into the operating system debugger. This command does NOT
# remove the requirement that the server console be
# physically secured. By default, SECURE CONSOLE is not
# invoked. For enhanced security SECURE CONSOLE may be
# invoked.
#
# SECURE CONSOLE
#
# The above commands provide enhanced security options
# that are NOT required for your server to be in the
# trusted configuration -- to meet the Class C2
# criteria and the Class F-C2/E2 criteria.
#
###########################################################-------------
--------------------------------------------------------
End of file. [SYS:SYSTEM\SECURE.NCF]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\SOLOMON.NCF]
---------------------------------------------------------------------
;Solomon IV Installation
SQLSTART
---------------------------------------------------------------------
End of file. [SYS:SYSTEM\SOLOMON.NCF]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\SQLSTART.NCF]
---------------------------------------------------------------------
;Solomon IV 100-User SQL Installation
BSTART
LOAD SSQL -w=32767 -z=99 -i=1
LOAD SSPXCOM -d=32767 -s=200 -w=99
---------------------------------------------------------------------
End of file. [SYS:SYSTEM\SQLSTART.NCF]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\SQLSTOP.NCF]
---------------------------------------------------------------------
UNLOAD SSPXCOM
UNLOAD SSQL
---------------------------------------------------------------------
End of file. [SYS:SYSTEM\SQLSTOP.NCF]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\STARTSS.NCF]
---------------------------------------------------------------------
; Open File Option Install--Open File Option startup and configuration
file
; NetWareDir=C:\NWSERVER
; SnapShotDir=C:\SNAPSHOT
load C:\SNAPSHOT\snapshot
path=C:\SNAPSHOT--------------------------------------------------------
-------------
End of file. [SYS:SYSTEM\STARTSS.NCF]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\UNISTART.NCF]
---------------------------------------------------------------------
load netdir
load rpcbstub
load tcp_nd
load local_nd
load tirpc
load netdb
load dispatch
load NISBIND
load NISSERV
load unixlib
---------------------------------------------------------------------
End of file. [SYS:SYSTEM\UNISTART.NCF]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\UNISTOP.NCF]
---------------------------------------------------------------------
unload unicon
unload dss
unload nisdmag
unload dnsagent
unload dssagt
unload nwipagt
unload srvagt
unload lpr_gwy
unload prlib
unload lockd
unload statd
unload nfsgw
unload hostg
unload named
unload nisgo
unload nisswdd
unload nisserv
unload nisbind
unload dispatch
unload unixlib
unload netdb
unload tirpc
unload local_nd
unload tcp_nd
unload rpcbstub
unload netdir
---------------------------------------------------------------------
End of file. [SYS:SYSTEM\UNISTOP.NCF]
*********************************************************************
*********************************************************************
Top of file. [SYS:SYSTEM\UNNMA2.NCF]
---------------------------------------------------------------------
#
# Unnma2.NCF - Unloads NetWare Management Agent (NMA) v2.6 NLMs
#
# There is a matching load file, Nma2.NCF, that will
# load the NetWare Management Agent v2.6 NLMs.
#
UNLOAD FINDNMS
UNLOAD NTREND
UNLOAD HOSTMIB
UNLOAD NWTRAP
UNLOAD SERVINST
---------------------------------------------------------------------
End of file. [SYS:SYSTEM\UNNMA2.NCF]
*********************************************************************
*********************************************************************
Top of file. [C:STARTUP.NCF]
---------------------------------------------------------------------
REM
REM The following line has been placed here for the Backup Exec for
NetWare
REM Open File Option.
REM
; 1/13/04 LOAD OTMDSK.DSK
; The following lines were moved or added by the NetWare Support Pack
LOAD C:\NWSERVER\DIAG411.NLM
LOAD C:\NWSERVER\PK411.NLM
LOAD C:\NWSERVER\CPUCHECK.NLM
; End of modifications made by NetWare Support Pack installation
SET RESERVED BUFFERS BELOW 16 MEG=200
; orginal from old server LOAD CPQSCSI.HAM SLOT=10003
; 1/13/04 LOAD CPQSCSI.HAM SLOT=10002
; 1/13/04 LOAD CPQSCSI.HAM SLOT=10003
; 1/13/04 test with new slot and move the load cpqshd.cdm up here
; tried slot = 1,2,3,4. It has no effect on the loading
load CPQSHD.CDM
load cpqscsi.ham slot=10002
; original from old server LOAD CPQARRAY.HAM SLOT=1
LOAD CPQARRAY.HAM SLOT=2
LOAD IDEATA.HAM PORT=1F0 INT=E
LOAD IDECD.CDM
; 1/13/04 LOAD CPQSHD.CDM
; 1/13/04 LOAD CPQSCD.DSK
; 1/13/04 LOAD CPQSDISK.DSK
; original LOAD CPQSCSI.HAM SLOT=10004
; move to above LOAD CPQSCSI.HAM SLOT=10003
; 1/13/04 LOAD CPQSASPI.NLM
; 1/13/04 load MAC
; 1/13/04 load LONG
; Open File Option Install--start disk filter device
load C:\SNAPSHOT\solitude
set days untouched before
compression=30----------------------------------------------------------
-----------
End of file. [C:STARTUP.NCF]
*********************************************************************
*********************************************************************
Top of file. [C:\CONFIG.SYS]
---------------------------------------------------------------------
files=35
buffers=30
country=001,437,c:\dos\country.sys
device=c:\dos\display.sys con=(ega,,1)
device=C:\fws2aspi.sys /cdboot
device=C:\fws2cd.sys
device=C:\cpqidecd.sys /D:CPQCDROM
rem lastdrive=m
---------------------------------------------------------------------
End of file. [C:\CONFIG.SYS]
*********************************************************************
*********************************************************************
Top of file. [C:\AUTOEXEC.BAT]
---------------------------------------------------------------------
@echo off
prompt $p$g
path=c:\dos
mscdex /d:cpqcdrom /v /m:50 /l:f
C:\DOS\KEYB.COM us,437
mode con cp prepare=((437) c:\dos\ega.cpi)
mode con cp select=437
nlsfunc
cd \NWSERVER
server
---------------------------------------------------------------------
End of file. [C:\AUTOEXEC.BAT]
*********************************************************************
*********************************************************************
Top of file. [C:ABEND.LOG]
---------------------------------------------------------------------
File size is 235419 bytes.
Only last 200 kbytes of file was scanned.
*******************************************
Server halted Wednesday, January 5, 2000 5:45:12 pm
Break 2: Server-4.11a: Page Fault Processor Exception (Error code
00000000)
Registers:
CS = 0008 DS = 0010 ES = 0010 FS = 0010 GS = 0010 SS = 0010
EAX = 00000000 EBX = 1EEB7D98 ECX = 00000000 EDX = 00000000
ESI = 1EEB7D94 EDI = 00000002 EBP = 1EEB7D48 ESP = 1EEB7D34
EIP = F106D3F8 FLAGS = 00010246
F106D3F8 663B5109 CMP DX,[ECX+09]= ?
EIP in UNICODE.NLM at code start +000013F8h
Running process: netdb 0 Process
Created by: NETDB.NLM
Stack pointer: 1EEB7E2C
Stack limit: 1EEB4010
*******************************************
Server halted Tuesday, February 29, 2000 12:23:19 pm
Break 1: Server-4.11a: Page Fault Processor Exception (Error code
00000000)
Registers:
CS = 0008 DS = 0010 ES = 0010 FS = 0010 GS = 0010 SS = 0010
EAX = 00001C3E EBX = 1D3E5050 ECX = 00000002 EDX = 000152E8
ESI = 00000001 EDI = 00000004 EBP = 1F76FD54 ESP = 1F76FD20
EIP = F14E98A2 FLAGS = 00010286
F14E98A2 3B4C2ACC CMP ECX,[EDX+EBP-34]= ?
EIP in BEPSVR.NLM at code start +000108A2h
Running process: Server 23 Process
Created by: SERVER.NLM
Stack pointer: 1F770068
Stack limit: 1F76D340
*******************************************
Server halted Monday, June 12, 2000 5:11:23 pm
Break 1: Server-4.11a: Page Fault Processor Exception (Error code
00000000)
Registers:
CS = 0008 DS = 0010 ES = 0010 FS = 0010 GS = 0010 SS = 0010
EAX = 00000000 EBX = 1F8F2D7C ECX = 00000000 EDX = 00000000
ESI = 1F8F2D78 EDI = 00000002 EBP = 1F8F2D2C ESP = 1F8F2D18
EIP = F106D3F8 FLAGS = 00010246
F106D3F8 663B5109 CMP DX,[ECX+09]= ?
EIP in UNICODE.NLM at code start +000013F8h
Running process: netdb 0 Process
Created by: NETDB.NLM
Stack pointer: 1F8F291C
Stack limit: 1F8EF010
*******************************************
Server halted Friday, August 30, 2002 8:18:44 am
Break 1: Server-4.11a: Page Fault Processor Exception (Error code
00000002)
Registers:
CS = 0008 DS = 0010 ES = 0010 FS = 0010 GS = 0010 SS = 0010
EAX = 00008B18 EBX = 01017028 ECX = 000FF3E0 EDX = 00017EFB
ESI = 000FF3E0 EDI = 00008B37 EBP = 1FC25900 ESP = 1FC258F0
EIP = F1419BE7 FLAGS = 00010206
F1419BE7 808C4369020000 OR [EBX+EAX*2+00000269]= ?,80
80
EIP in NAV.NLM at code start +00032BE7h
Running process: ScanEventThread Process
Created by: NAV.NLM
Stack pointer: 1FC25950
*******************************************
Server halted Friday, November 21, 2003 11:20:20 am
Break 1: Server-4.11a: Page Fault Processor Exception (Error code
00000000)
Registers:
CS = 0008 DS = 0010 ES = 0010 FS = 0010 GS = 0010 SS = 0010
EAX = 00000000 EBX = 0EA52D7C ECX = 00000000 EDX = 00000000
ESI = 0EA52D78 EDI = 00000002 EBP = 0EA52D2C ESP = 0EA52D18
EIP = F106D3F8 FLAGS = 00010246
F106D3F8 663B5109 CMP DX,[ECX+09]= ?
EIP in UNICODE.NLM at code start +000013F8h
Running process: netdb 0 Process
Created by: NETDB.NLM
Stack pointer: EA52E2C
Stack limit: EA4F010
---------------------------------------------------------------------
End of file. [C:ABEND.LOG]