Cam350 10 8 Torrent
Kerby Reynolds
A: Blank in the menu bar, click the right mouse button, click customize to enter. Select the keyboard option, select the menu where the command is located in the Category, select the command in the Commands, enter the key you want to define in Press New Shortcut, click Assign to complete. Can set any key.
How to choose line or pad in CAM350, and automatically capture their endpoints and center points, just as the V2001 in the press S key to select the line and automatically displays the current D code?
A: Press the "z" key, its role and V2001 S same. Sometimes press the "z" may not grasp the center then move the amount of dots, if not yet press "Page Up" to enlarge the mark box. Press the Q key corresponding PAD there will be D code status out.
A: Use Utilities -> Draw To Custom custom graphics D code, and then use the Utilities -> Draws To Flash -> Interactive command, select Define By Selecting D-Code, point Pick from list specify just the custom D-CODE Number can be
A: The command to add a blocking block is the same as to pave copper. Specific operations are as follows: Menu Add -> polygon pop polygon setting dialog box. If you want to draw a closed area of ??their own draw Draw Border, has drawn a closed area then select Select Border. The second column selected Vetor Fill; the last column selected Dcode; then press Edit, enter the block block pattern editor dialog box. Select a Dcode, enter their own want x, y interval, offset, etc .; Finally save a pat file, the next you do not have to edit.
A: Add -> Polygon, select the Select Border and Fill to Border two, will PolygonClearance spacing changed to zero. The filled polygon must be a closed figure. Click one side of the polygon and click the right mouse button, and then continue to tap the other side. After all the edges are lit, double-click the right button to fill it. Alternatively, you can use the Edit -> Line Change -> Join Segments command to fill all edges of the polygons together.
A: Use the EDIT -> LAYERS -> ALIGN command. Select this command in the think of a PAD on a fixed point on a single left click and then right click to confirm the point, and then click the button you want to move the layer of the corresponding point, then the point will turn white , Double-click the right button to align.
A: You can use the hole into the hole drilling; can also be converted into a line PAD drilling files. When the intersection of the aperture hole symbol is not easy to make Flash, or when the number of holes is not given (general guidance through hole), the above method is better. First copy all the PAD line to an empty layer, according to the size of the aperture after the Flash PAD will be removed after the extra copy into the drilling file can be.
A: Use Utilities -> Over / Under Size command. Template Layer Select the operating layer, Target Layer select the target layer, Enlarge to expand, reduce Reduce. Fill in the data to be expanded or reduced, and finally select the pad to be operated.
A: The milling path must be a closed path. The first step: first transformation of the outer gong belt (while the first set of tools), the second step, the selected how to go, the third step, derived. Tools -> Nc Editor -> Utilities -> Gerber to Mill Click
A: Tools -> Bed of Nails Editor, which is the production of the test frame module, before defining the properties of the layer, use the Utilities> Netlist Extract extracted network, to make the test frame.
A: You can copy all lines of PAD to an empty layer, use this layer and solder mask to calculate the extra line PAD to delete, and then this layer as a whole to enlarge 0.2mm (the overall zoom in or out: Utilities -> Over / Under) Finally, the solder mask of tin or block (large copper on the) can be copied in the past. Doing this method must be carefully compared with the original anti-welding, to prevent more anti-welding or less anti-welding.
When the data is covered by a large area of ??copper foil, the distance between the circuit or the PAD and the copper skin is not within the requirements of production, and if the external dimensions are large, is there a method for rapidly trimming the distance between the circuit or the PAD and the copper skin?
A: First, copy all the PADs of the line layer (the first layer) to an empty layer, and then delete the PAD corresponding to the PAD on the large copper sheet to amplify the remaining PADs as the reduced circuit layer (that is, the second layer) Then copy the first layer to an empty layer, the big copper removed as the third and so on. Laminated way: the first layer (plus layer), the second layer (layer), the third layer (plus layer). Generally speaking, in order to reduce the amount of data, we can only retain the first layer of large copper skin. If only the solder mask to a large copper spacing is not enough, you can put the enlarged (to meet the process capability) of the solder mask copy to an empty layer, the corresponding solder mask on the big copper removed after the remaining solder mask amplification as Second floor.
Note: After doing this in this way, be sure to use the command to convert multiple layers of Composite Utilities -> Convert Composite into a single layer, and then use this layer and the original carefully with the Anglysis -> Compare Layers command Check it out
In V2001 set the negative is very easy, and draw the line can be set can not be seen inside the CAM350 which is not necessarily a compound layer Caixing, or directly to build a new layer set to negative?
How to output negative film in CAM350 V8.0, for example, LAYER1 is the line, LAYER2 is the gear oil PAD, want to put these two layers together in CAM to produce a negative film, how can we put them two layers together?
A: Add -> Text, add text to specify the circular d code, direct selection of a round D code, not too much. You can also press A in the CAM350 to dial the aperture table, select or customize the circular D code!
A: a.cam350 does not support Chinese, you can add in the autocad and then import cam350. AutoCAD can be exported DXF and HPGL files, DXF although the deformation will be loaded in CAM350, but if you choose when loading the font, it is possible. And into HPGL, then fill it.
A: If your Logo is already a Gerber file, you can directly read the CAM350, and then copied to the silk screen layer on the line; BMP file can be used BMP2PCB software, and then use Protel into Gerber became; if it is AutoCAD format files, you can use AutoCAD to convert DXF format CAM350 read on the line.
6022c96aab