double wounded coils on Cobra Board

44 views
Skip to first unread message

Kalle Heinz

unread,
Oct 19, 2026, 4:45:22 PMOct 19
to MPF Users
Hi,

this (2nd picture)


I do understand and it works fine on the Cobra board with mpf. On an old Night Rider machine where I have only the playfield with all the parts but no original controller I want to use MPF and a Cobra board. The flipper finger coil looks like this:coil-min.jpg

the common terminal is here between the diodes. In the example from the mpf page I would have connected the HV bank to the common terminal and the single terminals to coil driver pulling it to ground when executed. Here, imho, this won't work since the wiring is different. Am I on the wrong track? The only way I see is to remove the left diode and flip it by 180 degrees. I am afraid to damage the thin wire.... I would as well buy a new coil, but how do I know how they are wired up? The night rider coil is rather slim, the other coils I have which would have the right wiring are rather fat and won't fit physically. Any help would be appreciated, I know only at the edge an MPF topic, but still hope to find some help here. Thanks!

Anthony Bates

unread,
Oct 20, 2026, 5:57:20 AMOct 20
to MPF Users
I had this exact same issue recently on a retheme project I am doing with an old Stern Nugent pin. If you are planning on using MPF and Cobrapin and getting rid of the EOS switches, you will actually need to adjust the wiring slightly further. On the old Night Rider pin I believe they used  AQ-25-500/34-4500 coils, which are wound in series rather than parallel. I initially tried wiring it the way you were preposing but because the coils are wound in series, I was getting absolutely no hold power. It turns out, I actually had to connect the 48V supply to the right lug (with the single thick wire), the pulse (initial strong flip) coil output to the middle lug with the thin and thick wires, and the hold coil output to the left lug with the thin wire. You would also need to swap the direction of both diodes so the bands are both pointing toward the right/48V. Some people actually remove the coil diodes entirely as Cobrapin has it's own built in diodes as well. It seems odd to have to change the wiring like this but it's because of how the coil is wound in series and how power is originally routed through the coil via the EOS switch, which isn't really needed with MPF and Cobrapin. 

It's actually not as difficult as it may seem with the thin hold winding. I did this on 4 flippers without breaking a wire. 
Another thing to note when you get to this stage, here is what my MPF coil config looked like with the flippers. Make sure you don't set the default hold power on the hold coils. Just set to allow_enable: true. I initially had the default hold power set to 1.0 and even though that is 100%, it was still weak. Removing that line in the yaml file fixed it. 
  c_flipper_left_main:
    number: 0-0-14           # bank A
    platform: opp
    default_pulse_ms: 30    # 25-500 power
    default_recycle: false
  c_flipper_lower_right_main:
    number: 0-0-12           # bank A
    platform: opp
    default_pulse_ms: 30     # 25-500
    default_recycle: false
  c_flipper_upper_right_main:
    number: 0-0-10           # bank A
    platform: opp
    default_pulse_ms: 30     # 25-500
    default_recycle: false


  # ---- Flipper holds (hold windings) — board 0 -----
  c_flipper_left_hold:
    number: 0-0-13           # bank A
    platform: opp
    allow_enable: true  
  c_flipper_lower_right_hold:
    number: 0-0-0            # bank A
    platform: opp
    allow_enable: true
  c_flipper_upper_right_hold:
    number: 0-0-9           # bank A
    platform: opp
    allow_enable: true

Kalle Heinz

unread,
Oct 20, 2026, 12:36:04 PMOct 20
to MPF Users
Thanks for that answer, that helped a lot to get a new view on it. I had to think a bit about your serial/parallel statement. I would claim, feel free to contradict, that we have to be a bit careful with these expressions here. See below, left side is the coil setup from the MPF link, right side is from the Night Rider coil. Top left is the original schematic drawing, easy to copy from the web page, that is what you call parallel I assume. Then I dragged the wires around and came to the schematic drawing at the bottom left, technically the very same setup. Would you call it parallel or serial? Then I did the same for the Night Rider coil, starting bottom right. Again easily copied from the picture in my original post. Again some wire pulling, not changing anything technically and you are at the top right. What is parallel and what is serial?

coil_wiring.png

Having said that, based on your input, I recognized that my statement "flip the left diode by 180 degrees" was wrong. It needs to be flipped and put from the left to the right lug and not touch the center lug. What you described is the following, how you did your setup:

coil_wiring_2.png

That might explain why your hold power is so low. Your hold coil is coil 1 (left), the current for coil 1 has first to go through coil 2 before it reaches coil 1 and thus you have a higher resistant -> lower current -> lower magnetic field -> lower force. If the left diode, the right leg terminates not in the center, but at 48V your hold power should be higher/better.

So far my theory... If I have missed something, or on the wrong track then happy to learn.

Thanks for sharing, it helped a lot to gain understanding. I dare now as well to unsolder the diodes, as well good hint (thanks!) that the Cobra board has already the diodes on it, so I just could cut off the diodes and be happy. Yes I want to get rid of the EOS switch.

Thanks!

Anthony Bates

unread,
Oct 20, 2026, 4:22:08 PMOct 20
to mpf-...@googlegroups.com
In your examples, yes both of the top pictures would be parallel and both of the bottom pictures would be in series. 
However, I don't believe the orientation of this photo would work:
image.png
This issue is that the diodes both have their bands pointing outward, which would require you to have the 48V connected to both outer lugs, which would leave you really only being able to use the middle lug and the #2 winding. 

I should have included photos in my original response to be more clear. This photo is how I originally had my coil set up when the hold power was low:
image.png
That was before I realised the coil was wound in series. So I had the 48V connected to the middle lug, the strong pulse control to the right lug and the hold control to the left lug. The problem with these old coils is the hold power relied on current flowing through both the thicker pulse winding AND the thinner hold winding to get the full hold power. So when I had it wired this way, the pulse power was working normally but I was only getting the hold power of the thinner winding. The flipper would still hold in an upright position but even a weak ball hit would knock it down. 

My current setup is working perfectly with the following orientation:
image.png
48V is connected to the right leg, pulse power to the middle, and hold power to the left. The #2 winding is the thicker wire and #1 is the thinner wire. With this setup, during the initial flipper pulse the current flows only through the #2 winding. During a flipper hold, the current flows entirely through both windings as intended to get the full hold power. In this orientation, the hold power shouldn't really be affected if the left diode bridge from the left lug to middle lug or if it bridged from the left lug to the right lug. Again, with this setup, both the pulse and hold power are working perfectly in my setup. It is important to note that this wiring is also without the EOS switches in place.

Also if you want to make it easier on yourself to reposition the diodes, you could just cut the current ones off and solder on new ones since diodes are so cheap. It would be quicker and less risk of damaging the thinner winding wire. 

Hope that makes a bit more sense and helps with your setup. 

Tony



--
You received this message because you are subscribed to a topic in the Google Groups "MPF Users" group.
To unsubscribe from this topic, visit https://groups.google.com/d/topic/mpf-users/9Epn-_rqvmk/unsubscribe.
To unsubscribe from this group and all its topics, send an email to mpf-users+...@googlegroups.com.
To view this discussion visit https://groups.google.com/d/msgid/mpf-users/b9243b76-152b-4724-8e05-aa65b9e5eb9an%40googlegroups.com.
Reply all
Reply to author
Forward
0 new messages