ME and NT
Bernie Asner
the host is ME.
The network was working using NT <-> 10/100Base-T Lan <-> D-Link
DSS-5+ <-> D-Link DFE-530TX <-> Windows 98.
I upgraded the 98 host to Windows ME and also upgraded to ADSL :) .
Went through the ME Wizard and now neither computer recognizes the
other.
The ME/Device Manager/Network adapters show
3Com ADSL PCI Modem LAN/RFC1483(Win ME)
D-Link DFE-530TX PCI Fast Ethernet Adapter (rev A)
Dial-Up Adapter
Internet Connection Sharing
Thanks for any good advice.
Bernie Asner
Carey Holzman
1) Download and install the networking patch (whether you think you need it
or not, it won't hurt anything) from Microsoft at
http://support.microsoft.com/support/kb/articles/Q272/9/91.ASP
2) Go into your Control Panel and double-click on the Network icon. Make
sure you have the following items installed:
A) Client for Microsoft Networks
B) Your Network adapter
C) TCP/IP
D) IPX/SPX
E) File and Printer Sharing for Microsoft Networks
3) Double-click on Client for Microsoft Networks. Make sure "Log on to
Windows NT domain" does NOT have a check in the box next to it. Select
"Logon and restore network connections". Click OK.
4) Double-click on your network adapter, and click the BINDINGS tab. Make
sure both TCP/IP and IPX/SPX are listed and both are CHECKED. Click OK.
5) Double click on TCP/IP, and click on the tab that says BINDINGS and
un-check File and Printer Sharing. Click on the tab that says ADVANCED, and
where it says Allow Binding to ATM, make sure the value is NO. Ensure there
is a check in the box at the bottom of the window that says "Set this
protocol to be the default protocol". Click OK.
6) Double-click on IPX/SPX and, on the NetBIOS tab, make sure it is
UN-checked where it says "I want to enable NetBIOS over IPX/SPX". Click on
the Bindings tab and make sure that Client for Microsoft Networks and File
and printer sharing BOTH ARE checked. Then click OK.
7) Double-click on File and Printer Sharing for Microsoft Networks. Click
once on Browse Master and make sure it's value is set to Automatic. Click
once on LM Announce and make sure it's value is set to NO. Click OK.
8) Below the ADD button, you'll see a line that says "Primary Network Logon"
, click the down arrow in the window below that and select "Windows Logon".
9) Below that is a button that says "File and Print Sharing.", click it
once. Make sure that "I want to be able to give others access to my files"
is checked and "I want to be able to allow others to print to my printer(s)"
is also checked. Click OK.
10) Click on the IDENTIFICATION tab and change your workgroup name to
WORKGROUP (please use all capitol letters, the workgroup name can be
case-sensitive on some PCs).
11) Click on the Access Control tab and make sure that Share-level access
control IS selected.
12) After you have re-booted, make sure that you select what resources you
want to share on each PC. To share the C: drive, double-click the My
Computer icon, Right click on the C: drive, click on the 'Sharing' tab and
select SHARED AS and then click OK. Repeat this process for sharing Printers
(right click on the printer you want to share), or individual directories
(right click on the yellow folder you wish to share). Optional password
protection can be found here as well.
13) Make sure you do steps 2 through 12 on all Win95 and Win98 PC's on your
network as well.
14) When you re-boot, you should be able to double-click My Network Place,
then Double-click Entire Network and click VIEW THE ENTIRE CONTENTS OF THIS
FOLDER (on the left side of the window). If the left side says HIDE THE
CONTENTS OF THIS FOLDER, then you did it right. You should see the name
WORKGROUP here, this should NOT be an empty window.
15) Click Tools, click Folder Options and click on the View tab. Make sure
that 'Automatically search for network folders and printers' IS checked. If
it is not, select it and click Apply. Next, click OK.
16) Close all windows.
17) Click Start, click Run and type REGEDIT and hit enter.
18) Click the "+" symbol next to Hkey_Current_User, click the "+" symbol
next to Software, click the "+" symbol next to Microsoft, click the "+"
symbol next to Windows, click the "+" symbol next to Current Version, click
the "+" symbol next to Explorer, click the "+" symbol next to NetCrawl and
then click on the yellow folder next to Printers.
19) Select each item listed in the window to the right, by clicking once on
it, and then press the delete button. DO NOT REMOVE THE FIRST ITEM LABELED
"(DEFAULT) Value Not Set". Repeat this process until the window on the
right is empty except for "(Default) value not set".
20) Next, just below the yellow 'Printers' folder, you should see another
yellow folder labeled "Shares", click once on the yellow folder.
21) Repeat step 12.
22) Click Registry (at the top of the windows) and Click Exit.
23) Re-boot the PC.
24) The network should now work. I have tried this method with Intel
Pentium, Pentium II, Pentium III, AMD k6-2, k6-3 and Athlon Thunderbird
processors all combined on the same network running Windows ME, Windows 98se
and a mix and match of network cards from Netgear, Dlink, SMC, Realtek,
LinkSys, Soho, and Xircom and this process worked flawlessly so that all of
the above computers running different versions of windows, having different
hardware, on a peer-to-peer network could see each other just fine.
25) If you click on My Network Places, and then double-click on Entire
Network and get the error "Cannot browse network", then do the following
steps:
26) On the computer that will be on most often, Click on Control Panel,
double-click the Network icon, double-click File and Printer Sharing for
Microsoft Networks, and where it says Browse Master, set it to enabled.
27) On all the other PC's on the LAN, set the above setting to DISABLED, so
that only ONE PC is running with Browse Master ENABLED.
28) If you are getting a SCRIPT ERROR when you double-click My Network
Places, then you must have Tweak UI installed and set to replace the first
icon that appears on the screen. Change this option back to it's default
setting, which should be My Documents.
If you are experiencing open windows of networked resources, this can be
caused by Norton Internet Security software. Also, you can delete the
offending drive letters in the contents of this registry setting. It should
help:
HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Explorer\MountPo
ints\_WantUI
(please note: the last part of the key may have a different name on your PC,
but whatever that first yellow folder is called, check it's contents. Remove
the drive letters you don't want to see. And please remember to back up your
registry before modifying it!
29) If this process does not work for you, make sure you have loaded the
latest drivers for your network card, make sure your network settings are
exactly as I described above to the last detail, try changing the slot the
network card is plugged into on the motherboard, make sure your cables are
good, make sure your hub or switch or router is working, and replace your
network card as a last resort.
30) As a side note: The Netgear FA310tx PCI Network Interface Card is
detected by Windows ME as an LNE card, which will not work properly. As long
as this card is plugged into your LAN, no computers will be able to browse
the network until you install the driver from Netgear for their card.
"Bernie Asner" <bas...@bellsouth.net> wrote in message
news:3A3D2393...@bellsouth.net...
Bernie Asner
Thank you very very much for this detailed response. MY NETWORK IS WORKING.
I followed everything you wrote with the exception of 2)D), because I didn't
know how to find it. Network still didn't work, so I did a bit of research, and
did find how to install IPX/SPX. Eureka, my host (ME) is now talking to the
NT. Still need to check out all the other things but this is wonderful. One
nit-picking correction. At step 21) do you really mean 12 or 19?
Again, thanks for your superb help.
Bernie Asner
Carey Holzman
Thanks.
Carey
"Bernie Asner" <bas...@bellsouth.net> wrote in message
news:3A3E28BD...@bellsouth.net...