Unsteady current of the biomass pellet making device
3 views
Skip to first unread message
cn.rich...@gmail.com
Jun 27, 2022, 11:23:28 PM6/27/22
to Machinery
The ring die as well as journalism roller of the biomass pellet making device rotate at a consistent speed, and also the working state of each immediate is generally the same. If the quantity of feed product is unmodified, the energy usage must likewise be relatively stable, as well as the existing will certainly be reflected on the electric motor. Likewise relatively steady.
When the biomass pellet making device maker is working, we readjust the feeding amount as long as the material thickness in the feeding location is less than the optimum starting factor of journalism location, it will directly affect the size of the reliable workspace of the pressing area and journalism area, and cause the present to stream.
When the biomass pellet making device maker is working, we readjust the feeding amount as long as the material thickness in the feeding location is less than the optimum starting factor of journalism location, it will directly affect the size of the reliable workspace of the pressing area and journalism area, and cause the present to stream.
Related post: biomass pellet making machine
The change and also the adjustment of the hourly output of the biomass pellet making maker, and if the density of the material layer in the feeding area is higher than the maximum starting point of the pressing location, in addition to increasing the thickness of the material layer in the feeding location, it will not affect the per hour outcome as well as power usage per unit time.
If there is any effect, it will certainly no longer cause changes in present as well as biomass pellet making maker outcome. Since the thickness of the product layer in the feeding zone exceeds the optimum starting point of the pressing area, the period between the pressing area and also the pressing area is constant with no adjustment. In the interval where the multi-feed product lies, the securing angle is more than the critical rubbing angle, as well as the material will certainly not be pressed right into the pressing location.
The change and also the adjustment of the hourly output of the biomass pellet making maker, and if the density of the material layer in the feeding area is higher than the maximum starting point of the pressing location, in addition to increasing the thickness of the material layer in the feeding location, it will not affect the per hour outcome as well as power usage per unit time.
If there is any effect, it will certainly no longer cause changes in present as well as biomass pellet making maker outcome. Since the thickness of the product layer in the feeding zone exceeds the optimum starting point of the pressing area, the period between the pressing area and also the pressing area is constant with no adjustment. In the interval where the multi-feed product lies, the securing angle is more than the critical rubbing angle, as well as the material will certainly not be pressed right into the pressing location.
Related post: biomass pellet plant
By doing this, with the increase of the feeding amount of the biomass pellet making device, the balance of in and out is broken, and the in is above the out, and the product layer in the feeding area is It will certainly accumulate thicker and thicker until all the spaces are loaded as well as blocked to the feed port, to ensure that the biomass pellet device can not function generally. Currently, the current will enhance.
In the actual work of the biomass pellet making maker, with the change of the feeding amount, the rapid outcome and the current of the main motor will certainly transform accordingly. As well as when the feeding thickness does not go beyond the maximum beginning factor of the pressing location, it will not create more and more worldly layers in the feeding area as a result of the increase in the quantity of powder we feed.
By doing this, with the increase of the feeding amount of the biomass pellet making device, the balance of in and out is broken, and the in is above the out, and the product layer in the feeding area is It will certainly accumulate thicker and thicker until all the spaces are loaded as well as blocked to the feed port, to ensure that the biomass pellet device can not function generally. Currently, the current will enhance.
In the actual work of the biomass pellet making maker, with the change of the feeding amount, the rapid outcome and the current of the main motor will certainly transform accordingly. As well as when the feeding thickness does not go beyond the maximum beginning factor of the pressing location, it will not create more and more worldly layers in the feeding area as a result of the increase in the quantity of powder we feed.
Related post: 10T/H Biomass Wood Pellet Plant in USA
As has been claimed prior to, the location that can create immediate output and also energy consumption adjustments need to be the two locations of job and product layers - the compression location and also the biomass pellet device extrusion area, so we think that the third area mentioned over- - The practical presence of the feeding location has particular conditions.
That is to say, the fed material layer is dispersed in the compaction location, the extrusion area and the feeding area whose overall density does not go beyond the optimum access point of the compaction area.
The biomass pellet making equipment will certainly function generally under the allowed power. If the amount is too huge and exceeds the thickness of the optimum beginning point of the compaction location, the material layer will certainly accumulate and also slowly rise, and also the biomass pellet making maker will not function normally. Present is changing.
As has been claimed prior to, the location that can create immediate output and also energy consumption adjustments need to be the two locations of job and product layers - the compression location and also the biomass pellet device extrusion area, so we think that the third area mentioned over- - The practical presence of the feeding location has particular conditions.
That is to say, the fed material layer is dispersed in the compaction location, the extrusion area and the feeding area whose overall density does not go beyond the optimum access point of the compaction area.
The biomass pellet making equipment will certainly function generally under the allowed power. If the amount is too huge and exceeds the thickness of the optimum beginning point of the compaction location, the material layer will certainly accumulate and also slowly rise, and also the biomass pellet making maker will not function normally. Present is changing.
Related post: RICHI pellet making machine
Through the above analysis, allow's go over some sensations showed by the biomass pellet making maker under 2 feasible working problems:
( 1 )When the power of the main electric motor is not large sufficient compared to the equivalent biomass pellet making equipment granulation parameters, the density of our feed is at the end of the extrusion zone as well as the optimum access point of the compression zone (this will certainly differ with the raw products, compression proportion, efficient length-diameter proportion, humidity, stress rollers as well as other variable aspects to readjust as necessary), usually will not exceed the maximum beginning factor, with the boost of the feeding amount, the compression area will transform appropriately.
The size of the period will be shortened, as well as the interval length of the press area will slowly increase appropriately, and the current of the primary motor will likewise progressively enhance until it reaches the maximum allowed usage. If the existing gets to the protection value we set, as well as the thickness of the feeding product has not exceeded the density of the maximum starting factor of the biomass pellet device pushing area, if the feeding amount is raised, the safety system will act, and also the excess powder will certainly be released. In order to make certain the regular function of biomass pellets.
Through the above analysis, allow's go over some sensations showed by the biomass pellet making maker under 2 feasible working problems:
( 1 )When the power of the main electric motor is not large sufficient compared to the equivalent biomass pellet making equipment granulation parameters, the density of our feed is at the end of the extrusion zone as well as the optimum access point of the compression zone (this will certainly differ with the raw products, compression proportion, efficient length-diameter proportion, humidity, stress rollers as well as other variable aspects to readjust as necessary), usually will not exceed the maximum beginning factor, with the boost of the feeding amount, the compression area will transform appropriately.
The size of the period will be shortened, as well as the interval length of the press area will slowly increase appropriately, and the current of the primary motor will likewise progressively enhance until it reaches the maximum allowed usage. If the existing gets to the protection value we set, as well as the thickness of the feeding product has not exceeded the density of the maximum starting factor of the biomass pellet device pushing area, if the feeding amount is raised, the safety system will act, and also the excess powder will certainly be released. In order to make certain the regular function of biomass pellets.
Related post: https://www.pellet-richi.com/wood-pellet-machine/biomass-pellet-mill.html
( 2 ) Intend the power of the primary motor is large or the electric motor stops working to overload after the density of the feeding product exceeds the density of the optimum beginning point of journalism area as a result of the comprehensive adjustments of many variables. Currently, the powder fed to the people can not raise the moment output, neither will certainly it cause the boost of the major motor existing, yet can only continue to enhance the powder stack built up in the machine until the inner cavity of the biomass pellet press equipment is obstructed.
Cause the biomass pellet making machine to not function effectively. Naturally, this unique phenomenon hardly ever happens in actual production (if the raw material moisture is too huge, the reliable facet proportion is as well little, the pressure roller is drastically used and also the space is not readjusted properly, the raw material is changed, and so on, this phenomenon may occur), this is our undesired conditions.
Thorough evaluation of the initial generally made use of functioning state, it is uncomplicated to understand that on the facility that the appropriate conditions are unmodified, with the change of the feeding amount, the interval size of the compression area and the extrusion area is within a particular array Matching changes are additionally made (the feed circulation price is reduced, the length of the extrusion area is minimized, and also the length of the compression area is lengthened; otherwise, the extrusion zone is prolonged as well as the compression area is reduced), and also the feeding quantity does not go beyond the stress. When the thickness of the optimum starting factor of the tight area is concerned, the lengths of the above two intervals are not a constant value when this article is written. The larger the extrusion zone length value, the higher the biomass pellet maker production efficiency and the longer the pellet length per extrusion per roller.
Therefore, it is concluded that the factors of current instability under the condition of controlling the feeding amount need to be investigated from the moisture content of the raw material, the effective aspect ratio is too small, the pressure roller is severely worn and the gap is not adjusted properly, and the raw materials are replaced.
RICHI MACHINERY has been established for more than 25 years, specializing in biomass pellet making machine for sale, the development and production of single/complete pellet production lines such as animal feed, biomass fuel, wood waste, grass, straw, organic fertilizer, etc, and provide design and services for EPC/Turnkey projects!
( 2 ) Intend the power of the primary motor is large or the electric motor stops working to overload after the density of the feeding product exceeds the density of the optimum beginning point of journalism area as a result of the comprehensive adjustments of many variables. Currently, the powder fed to the people can not raise the moment output, neither will certainly it cause the boost of the major motor existing, yet can only continue to enhance the powder stack built up in the machine until the inner cavity of the biomass pellet press equipment is obstructed.
Cause the biomass pellet making machine to not function effectively. Naturally, this unique phenomenon hardly ever happens in actual production (if the raw material moisture is too huge, the reliable facet proportion is as well little, the pressure roller is drastically used and also the space is not readjusted properly, the raw material is changed, and so on, this phenomenon may occur), this is our undesired conditions.
Thorough evaluation of the initial generally made use of functioning state, it is uncomplicated to understand that on the facility that the appropriate conditions are unmodified, with the change of the feeding amount, the interval size of the compression area and the extrusion area is within a particular array Matching changes are additionally made (the feed circulation price is reduced, the length of the extrusion area is minimized, and also the length of the compression area is lengthened; otherwise, the extrusion zone is prolonged as well as the compression area is reduced), and also the feeding quantity does not go beyond the stress. When the thickness of the optimum starting factor of the tight area is concerned, the lengths of the above two intervals are not a constant value when this article is written. The larger the extrusion zone length value, the higher the biomass pellet maker production efficiency and the longer the pellet length per extrusion per roller.
Therefore, it is concluded that the factors of current instability under the condition of controlling the feeding amount need to be investigated from the moisture content of the raw material, the effective aspect ratio is too small, the pressure roller is severely worn and the gap is not adjusted properly, and the raw materials are replaced.
RICHI MACHINERY has been established for more than 25 years, specializing in biomass pellet making machine for sale, the development and production of single/complete pellet production lines such as animal feed, biomass fuel, wood waste, grass, straw, organic fertilizer, etc, and provide design and services for EPC/Turnkey projects!
Reply all
Reply to author
Forward
0 new messages