|
BeeProg
Programmer
Extremely fast universal USB/LPT interfaced
programmer.
Short description: وصف سريع
-
44587 supported devices by
2.57 version of SW (19. Feb. 2009)
-
extremely fast programming, one of the
fastest programmers in this category. Programs 16-Mbit Flash
memory less than 18 seconds
-
48-pins powerful pindrivers, no adapter required for any
DIL devices
-
connector for in-circuit programming
(ISP)
-
dual connection to PC: USB or parallel (printer) port
-
USB 2.0/1.1 compatible interface
-
alternatively high-speed IEEE 1284
(ECP/EPP) printer-port (LPT) interface
-
comfortable and easy to use control program,
Windows 95/98/Me/NT/2000/XP/2003/XPx64
Features الميزات
GENERAL
- First member of new USB-compatible generation of Windows
95/98/ME/NT/2000/XP/2003/XP64 based ELNEC universal
programmers built to meet the strong demand of the developers
community for the fast and reliable universal programmer.
- Supports all kinds of types and silicon
technologies of today and tomorrow programmable devices
without family-specific module. You have freedom to choose the optimal
device for your design. Using built-in in-circuit serial programming
(ISP) connector, the programmer is able to program ISP
capable chips in circuit.
- BeeProg isn't only a programmer, but also a tester
of TTL/CMOS logic ICs and memories. Furthermore, it allows generation of
user-definable test pattern sequences.
- Provides very competitive price coupled with excellent hardware
design for reliable programming. Probably best "value for
money"programmer in this class.
- Very fast programming due to high-speed FPGA driven
hardware and execution of time-critical routines inside of the
programmer. At least fast than competitors in this category, for many
chips much faster than most competitors. As a result, when used in
production this one-socket-programmer waits for an operator, and not the
other way round.
- BeeProg interfaces with the IBM PC 486 compatible or higher,
portable or desktop personal computers through USB
(2.0/1.1) port or any standard parallel (printer) port.
Programmer also supports IEEE1284 (ECP/EPP) high-speed parallel port.
Support of both USB/LPT port connection gives you the choice to connect
the BeeProg programmer to any PC, from latest notebook to older desktop
without USB port.
HARDWARE
- FPGA based totally reconfigurable 48
powerful TTL pindrivers provide H/L/pull_up/pull_down
and read capability for each pin of socket. Advanced pindrivers
incorporate high-quality high-speed circuitry to
deliver signals without overshoot or ground bounce for all supported
devices. Pin drivers operate down to 1.8V so you'll be ready to program
the full range of today's advanced low-voltage devices.
- The programmer performs device insertion test
(wrong or backward position) and contact check (poor
contact pin-to-socket) before it programs each device. These
capabilities, supported by overcurrent protection and
signature-byte check help prevent chip damage due to
operator error.
- The selftest capability allow to run diagnostic part of software to
thoroughly check the health of the programmer.
- Built-in protection circuits eliminate damage of
programmer and/or programmed device due to environment or operator
failure. All the inputs of the BeeProg programmer, including the ZIF
socket, connection to PC and power supply input, are protected
against ESD up to 15kV.
- BeeProg programmer performs programming
verification at the marginal level of
supply voltage, which, obviously, improves programming yield, and
guarantees long data retention.
- Various socket converters are available to handle
device in PLCC, SOIC, PSOP, SSOP, TSOP, TSSOP, TQFP, QFN (MLF), SDIP,
BGA and other packages.
SOFTWARE
- Programmer is driven by an easy-to-use control
program with pull-down menu, hot keys and on-line help. Selecting of
device is performed by its class, by manufacturer or simply by typing a
fragment of vendor name and/or part number.
- Standard device-related commands (read, blank
check, program, verify, erase) are boosted by some test
functions (insertion test, signature-byte check), and some
special functions (autoincrement, production mode -
start immediately after insertion of chip into socket).
- All known data formats are supported. Automatic file format
detection and conversion during loading of file.
- The rich-featured auto-increment function enables
one to assign individual serial numbers to each programmed device - or
simply increments a serial number, or the function enables one to read
serial numbers or any programmed device identification signatures from a
file.
- The software also provide a many information about programmed
device. As a special, the drawing of all available
packages are provided. The software provide also
explanation of chip labelling (the meaning of prefixes
and suffixes at the chips) for each supported chip.
- The software provide a full information for ISP implementation:
Description of ISP connector pins for currently selected chip,
recommended target design around in-circuit programmed chip and other
necessary information.
- The remote control feature allows to be PG4UW software flow
controlled by other application – either using .BAT file commands or
using DLL file.
DLL file, examples (C/PAS) and manual are part of
standard software delivery.
- Jam files of JEDEC standard JESD-71 are interpreted
by Jam Player. Jam files are generated by design
software which is provided by manufacturer of respective programmable
device. Chips are programmer in-ZIF or through ISP connector (IEEE
1149.1 Joint Test Action Group (JTAG) interface).
- VME files are interpreted by VME Player. VME file
is a compressed binary variation of SVF file and contains high-level
IEEE 1149.1 bus operations. VME files are generated by design software
which is provided by manufacturer of respective programmable device.
Chips are programmer in-ZIF or through ISP connector (IEEE 1149.1 Joint
Test Action Group (JTAG) interface).
- Multiple devices are possible to program and test via JTAG chain:
JTAG chain (ISP-Jam) or JTAG chain (ISP-VME).
Specification المواصفات
HARDWARE
Base unit, DACs
- USB 2.0 port
- FPGA based IEEE 1284 slave printer port, up to 1MB/s transfer rate
- on-board intelligence: powerful microprocessor and FPGA based state
machine
- three D/A converters for VCCP, VPP1, and VPP2, controllable rise and
fall time
- VCCP range 0..8V/1A
- VPP1, VPP2 range 0..26V/1A
- autocalibration
- selftest capability
- protection against surge and ESD on power supply input, parallel
port connection
ZIF socket, pindriver
- 48-pin DIL ZIF (Zero Insertion Force) socket accepts both 300/600
mil devices up to 48-pin
- pindrivers: 48 universal
- VCCP/VPP1/VPP2 can be connected to each pin
- perfect ground for each pin
- FPGA based TTL driver provides H, L, CLK, pull-up, pull-down on all
pindriver pins
- analog pindriver output level selectable from 1.8 V up to 26V
- current limitation, overcurrent shutdown, power failure shutdown
- ESD protection on each pin of socket (IEC1000-4-2: 15kV air, 8kV
contact)
- continuity test: each pin is tested before every programming
operation
ISP connector
- 10-pin male type with missinsertion lock
- 5 TTL pindrivers, provides H, L, CLK, pull-up, pull-down; level H
selectable from 1.8V up to 5V to handle all (low-voltage including)
devices.
- 1x VCCP voltage (range 2V..7V/100mA), can be applied to pins 1, 3
- programmed chip voltage (VCCP) with both source/sink capability and
voltage sense
- 1x VPP voltage (range 2V..25V/50mA), can be applied to pins
2,3,4,6,8,10
- target system supply voltage (range 2V..6V/250mA)
DEVICE SUPPORT الدارات
المتكاملة التي تبرمجها
Programmer, in ZIF socket
- EPROM: NMOS/CMOS, 2708*, 27xxx and 27Cxxx series, with 8/16 bit data
width, full support for LV series
- EEPROM: NMOS/CMOS, 28xxx, 28Cxxx, 27EExxx series, with 8/16 bit data
width
- Flash EPROM: 28Fxxx, 29Cxxx, 29Fxxx, 29BVxxx, 29LVxxx, 29Wxxx,
49Fxxx series, from 256Kbit to 32Mbit, with 8/16 bit data width, full
support for LV series
- Serial E(E)PROM: 24Cxxx, 24Fxxx, 25Cxxx, 45Dxxx, 59Cxxx, 25Fxxx,
25Pxxx, 85xxx, 93Cxxx, NVM3060, MDAxxx series, full support for LV
series
- Configuration (EE)PROM: XCFxxx, XC17xxxx, XC18Vxxx, EPCxxx, AT17xxx,
37LVxx
- 1-Wire E(E)PROM: DS1xxx, DS2xxx
- PROM: AMD, Harris, National, Philips/Signetics, Tesla, TI
- NV RAM: Dallas DSxxx, SGS/Inmos MKxxx, SIMTEK STKxxx, XICOR 2xxx,
ZMD U63x series
- PLD: Altera: MAX 3000A, MAX 7000A, MAX 7000B, MAX 7000S, MAX7000AE
- PLD: Lattice: ispGAL22V10x, ispLSI1xxx, ispLSI1xxxEA, ispLSI2xxx,
ispLSI2xxxA, ispLSI2xxxE, ispLSI2xxxV, ispLSI2xxxVE, ispLSI2xxxVL,
LC4xxxB/C/V/ZC, M4-xx/xx, M4A3-xx/xx, M4A5-xx/xx, M4LV-xx/xx
- PLD: Xilinx: XC9500, XC9500XL, XC9500XV, CoolRunner XPLA3,
CoolRunner-II
- other PLD: SPLD/CPLD series: AMI, Atmel, AMD-Vantis, Gould, Cypress,
ICT, Lattice, NS, Philips, STM, VLSI, TI
- Microcontrollers 48 series: 87x41, 87x42, 87x48, 87x49, 87x50 series
- Microcontrollers 51 series: 87xx, 87Cxxx, 87LVxx, 89Cxxx, 89Sxxx,
89LVxxx, all manufacturers, Philips LPC series
- Microcontrollers Intel 196 series: 87C196 KB/KC/KD/KT/KR/...
- Microcontrollers Atmel AVR: AT90Sxxxx, ATtiny, ATmega series
- Microcontrollers Cypress: CY8Cxxxxx
- Microcontrollers ELAN: EM78Pxxx
- Microcontrollers MDT 1xxx and 2xxx series
- Microcontrollers Microchip PICmicro: PIC10xxx, PIC12xxx, PIC16xxx,
PIC17Cxxx, PIC18xxx, dsPIC series
- Microcontrollers Motorola (Freescale): 68HC05, 68HC08, 68HC11 series
- Microcontrollers Myson MTV2xx, 3xx, 4xx and 5xx series
- Microcontrollers National: COP8xxx series
- Microcontrollers NEC: uPD78Fxxx series
- Microcontrollers Scenix (Ubicom): SXxxx series
- Microcontrollers SGS-Thomson: ST6xx, ST7xx, ST10xx series
- Microcontrollers TI: MSP430 and MSC121x series
- Microcontrollers ZILOG: Z86/Z89xxx and Z8xxx series
- Microcontrollers other: EM Microelectronic, Fujitsu, Goal
Semiconductor, Hitachi, Holtek, Princeton, Macronix, Winbond,
Infineon(Siemens), Samsung, Toshiba, ...
Programmer, through ISP connector
- Serial E(E)PROM: IIC series, MW series, SPI series, KEELOQ series,
serial data Flash, PLD configuration memories
- Microcontrollers Atmel: AT89Sxxx, AT90Sxxxx, ATtiny, ATmega series
- Microcontrollers Cypress: CY8C2xxxx
- Microcontrollers Elan: EM78Pxxx, EM6xxx series
- Microcontrollers EM Microelectronic: 4 and 8 bit series
- Microcontrollers Microchip PICmicro: PIC10xxx, PIC12xxx, PIC16xxx,
PIC17xxx, PIC18xxx, dsPIC series
- Microcontrollers Motorola/Freescale: HC11 series, HC908 series (both
5-wire, All-wire)
- Microcontrollers NEC: uPD7xxx series
- Microcontrollers Philips: LPC2xxx series, LPC series, 89xxx series
- Microcontrollers Scenix (Ubicom): SXxxx series
- Microcontrollers TI: MSP430 (both JTAG and BSL series), MSC12xxx
series
- PLD: Lattice: ispGAL22xV10x, ispLSI1xxxEA, ispLSI2xxxE, ispLSI2xxxV,
ispLSI2xxxVE, ispLSI2xxxVL, M4-xx/xx, M4LV-xx/xx, M4A3-xx/xx,
M4A5-xx/xx, LC4xxxB/C/V/ZC
- Various PLD (also by JAM player/JTAG support):
Altera: MAX 3000A,
MAX 7000A, MAX 7000B, MAX 7000S, MAX 9000, MAX II
Xilinx: XC9500,
XC9500XL, XC9500XV, CoolRunner XPLA3, CoolRunner-II
I.C. Tester يمكن أستخدامها أيضا لفحص الدارات
المتكاملة
- TTL type: 54,74 S/LS/ALS/H/HC/HCT series
- CMOS type: 4000, 4500 series
- Static RAM: 6116 .. 624000
- User definable test pattern generation
Package support
- support all devices in DIP with default socket
- package support includes DIP, SDIP, PLCC, JLCC, SOIC, SOP, PSOP,
SSOP, TSOP, TSOPII, TSSOP, QFP, PQFP, TQFP, VQFP, QFN (MLF), SON, BGA,
EBGA, FBGA, VFBGA, UBGA, CSP, SCSP etc.
- support devices in non-DIP packages up to 48 pins with universal
adapters
- programmer is compatible with third-party adapters for non-DIP
support
Programming speed
Notes:
- It is important to know, we always use random numbers pattern for
programming speed testing. Some our competitors use "sparse" pattern,
where only few non-Blak data are programmed or are there are used data
with only few 0 bits (FE, EF, etc.). This cheating approach can
"decrease" programming time considerable. If you plan to compare, ask
always which pattern they use.
- The programming speed depends on PC speed only slightly.
- If the programmer attached to PC through LPT port, the programming
might take longer.
| Device |
Size [bits] |
Operation |
Time |
| M50FW080 (parallel Flash) |
100000Hx8 (8 Mega) |
programming and verify |
22 sec. |
| AM29DL323DB (parallel Flash) |
208000Hx16 (32 Mega) |
programming and verify |
31 sec. |
| AM29DL640 (parallel Flash) |
400080Hx16 (64 Mega) |
programming and verify |
61 sec. |
| AT45D081 (serial Flash) |
108000Hx8 (16 Mega) |
programming and verify |
41 sec. |
| AT89C51RD2 (microcontroller) |
10000Hx8 |
programming and verify |
15 sec. |
| PIC18LF452 (microcontroller) |
4000Hx16 |
programming and verify |
4 sec. |
| Conditions: PC Pentium 4, 2.4 GHz,
USB 2.0, Windows XP. |
SOFTWARE
- Algorithms: only manufacturer approved or certified
algorithms are used. Custom algorithms are available at additional cost.
- Algorithm updates: software updates are available
regulary, approx. every 2 weeks, free of charge.
- Main features: revision history, session logging,
on-line help, device and algorithm information.
Device operations
- standard:
- intelligent device selection by device type, manufacturer or typed
fragment of part name
- automatic ID-based selection of EPROM/Flash EPROM
- blank check, read, verify
- program
- erase
- configuration and security bit program
- illegal bit test
- checksum
- interprete the Jam Standard Test and Programming Language (STAPL),
JEDEC standard JESD-71
- interprete the VME files compressed binary variation of SVF files
security
- insertion test, reverse insertion check
- contact check
- ID byte check
special
- production mode (automatic start immediately after device
insertion)
- auto device serial number increment
- statistic
- count-down mode
Buffer operations
- view/edit, find/replace
- fill/copy, move, byte swap, word/dword split
- checksum (byte, word)
- print
File load/save
- no download time because programmer is PC controlled
- automatic file type identification/recognition
Supported file formats
- unformatted (raw) binary
- HEX: Intel, Intel EXT, Motorola S-record, MOS, Exormax, Tektronix,
ASCII-SPACE-HEX,, ASCII HEX
- Altera POF, JEDEC (ver. 3.0.A), eg. from ABEL, CUPL, PALASM, TANGO
PLD, OrCAD PLD, PLD Designer ISDATA, etc.
- JAM (JEDEC STAPL Format), JBC (Jam STAPL Byte Code), STAPL (STAPL
File) JEDEC standard JESD-71
- VME (ispVME file VME2.0/VME3.0)
GENERAL
PC system requirements
- Common, software related requirements
- Programmer hardware related requirements:
- either one USB port, 2.0 compatible
- or one (parallel) printer port with nothing attached, the IEEE
1284 compatible printer port (ECP/EPP) on PCI bus recommended
Operation
- operating voltage 15V..18V DC, max. 1A
- power consumption max. 12W active, about 2W sleep
- dimensions 160x190x42 mm (6.3x7.5x1.7 inch)
- weight (without external adapter) 0.9kg (1.98 lb)
- temperature 5°C ÷ 40°C (41°F ÷ 104°F)
- humidity 20%..80%, non condensing
Package includes
- BeeProg programmer
- switching power adapter 100..240V AC/15V DC/1A
- connection cable PC-programmer, LPT port
- connection cable PC-programmer, USB port
- ISP cable
- diagnostic POD for selftest of the programmer
- anti-dust cover for ZIF socket
- user manual
- software
- registration card
- calibration test report
- transport case
|
