Calibration of IQI

329 views
Skip to first unread message

Manish Kumar

unread,
Oct 9, 2020, 11:39:47 PM10/9/20
to material...@googlegroups.com
Dear Sir,
Which clause number as per ASME section V, calibration of IQI/ penetrameter is required ?.

Pl advise

--
Regards

Manish Kumar
Inspection(Mechanical) Engineer
PDIL-HURL Barauni site

james gerald

unread,
Oct 10, 2020, 4:58:00 AM10/10/20
to material...@googlegroups.com
Please see snap shot of ASME Sec.V  Article 2 below.

Inline image
Inline image


Thanks & Regards

J.Gerald Jayakumar



--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-weld...@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAHfQ4k4-WLe8zRvsgZN%2B1vbCb%3D%3DSMc2E1kOQ7sFZGT65dEnXiQ%40mail.gmail.com.

james gerald

unread,
Oct 10, 2020, 4:58:03 AM10/10/20
to material...@googlegroups.com
ASME Sec.V defines only about Densitometer Calibration as explained in the previous mail.

IQI/Penetrameter Clibration is not defined in the Code as the IQI comes in a packed condition and there will be no variation observed during usage and incase if it is damaged then it can be replaced.

nly thing cansideredo using IQI is the selection of IQI based on the material used and of similar 



Thanks & Regards

J.Gerald Jayakumar

0091-6382552037

On Saturday, 10 October, 2020, 10:39:37 am GMT+7, Manish Kumar <mkmk...@gmail.com> wrote:
--

SENTHILKUMAR SWAMINATHAN

unread,
Oct 10, 2020, 5:45:49 AM10/10/20
to 'james gerald' via Materials & Welding
Please refer article 22 in section 5. Long back I seen. 


SENTHILKUMAR SWAMINATHAN

unread,
Oct 11, 2020, 12:43:44 AM10/11/20
to material...@googlegroups.com
In ASME V Art-22, SE747 - its mentioned 
"Conformance to specified tolerances for dimensional values"

Regards, S.SENTHILKUMAR


George Dilintas

unread,
Oct 11, 2020, 10:27:53 PM10/11/20
to material...@googlegroups.com
IQIs are not calibrated.
For penetrameter calibration refer to T-262

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-weld...@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAHfQ4k4-WLe8zRvsgZN%2B1vbCb%3D%3DSMc2E1kOQ7sFZGT65dEnXiQ%40mail.gmail.com.


--
Dr. Georgios Dilintas,
Dipl. Ing. In Aeronautic and Space Engineering
Ph.D in Mechanics of Solids - Computational Mechanics
A.I.S, A.N.I, IRCA Lead Auditor
Welding, Stress Analysis, Corrosion, QA/QC, Failure Analysis, Risk Analysis
Reply all
Reply to author
Forward
0 new messages