REQUIRED FILLER WIRE FOR (ASTM A312-Gr UNS 31254) Super Austenetic Stainless Steel

[Muhammad Azeem]

Gents,

I need your valuable support to assist about the filler wire to be used for Super Austenitic Stainless Steel (ASTM A 312 Gr UNS 31254) ??

Regards,

Muhammad Azeem Iqbal

Welding Inspector Aramco Approved

053110-8577/0554453626/0590071467

[james gerald]

Please refer attached article.

Thanks & Regards

J.Gerald Jayakumar

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-weld...@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAHqH7yAQ5mG4ZSP1b8dm-3X7HWASTFGeuv0Y_s2hqR-qGHH2mw%40mail.gmail.com.

[Mohd Siraj]

Avesta P54 is a good choice for SAS and it is affluently available in KSA, very cost effective.

just take care of good cleaning and avoid any kind of moisture on the surface and hope u pass G48!

[Shahil Saini]

Hello Everyone,

Why filler wire selection of A 312 UNS 31254 is not mentioned in Table 6 of SA 312 of ASME Sec II Part A1? 

[Muhammad Azeem]

Dear Siraj,

Thanks for your valuable response, Avesta P54 is a Brand ,I need to check if this manufacturer is approved by Aramco SAP & What is the AWS/SFA number for this filler wire ??

As I consult with 3rd Party they recommend  ERNiCrMo3,F43  ??

Regards,

Muhammad Azeem Iqbal

Welding Inspector Aramco Approved

053110-8577/0554453626/0590071467

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-weld...@googlegroups.com.

To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/8e1f3a9f-2d27-44fa-b777-6a9e6ed119ddn%40googlegroups.com.

[Aqil Abbas]

Hi,

I believe you should go for ERNiCrMo3/ENiCrMo3. We have used the same filler material for 2-3 of our project with aramco.

To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAHqH7yD1CT5a7K__qDYcWJkdoUKJiS_b6-WAZ1ZYesQAb55yww%40mail.gmail.com.

--

OPEN TO NEW CONNECTIONS

https://www.linkedin.com/in/aqil-abbas/

Best Regards,

Aqil Abbas

Welding QA/QC Inspector

Saudi Aramco Onshore Maintain Potential Project

Mobile # +966-58-204-4155

[james gerald]

Pls check SA358

Thanks & Regards

J.Gerald Jayakumar

To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CALfBO_-d-0ndkOGabk%3DtJ1Y6Qi6CoBObO9WG8cc5oY3TFRL1%2Bw%40mail.gmail.com.

[Muhammad Azeem]

Hi Aqil,

As per your given filler wire detail ERNiCrMo3 , I will go with this option .

Regards,

Muhammad Azeem Iqbal

Welding Inspector Aramco Approved

053110-8577/0554453626/0590071467

To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAPyajwTMYsjs7UAx42gOoTpKyXHrsajrNGHPtwYEWXs1tGx12Q%40mail.gmail.com.

[Muhammad Zulfiqar Ali]

Dear Azeem,

Please be noted that manufacturing SA approval is not required for these kinds of material, you may procure this material through any approved supplier if needed. 

On Wed, Feb 9, 2022 at 10:54 AM Muhammad Azeem <azee...@gmail.com> wrote:

To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAHqH7yD1CT5a7K__qDYcWJkdoUKJiS_b6-WAZ1ZYesQAb55yww%40mail.gmail.com.

--

Kind Regards,

M Zulfiqar Ali

Mob: +966 (0) 56 089 1836

[Prasad Talari]

Hi Iqbal,

ER Ni Cr Mo-3 (F No 43) is the right choice for this , i ve qualified a PQR for this material

Regards

Prasad Talari

Welding Engineer

GAC-Qatar

To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAHqH7yAh4G-RJD%3DuDx69CrFWOB8iKgWYdGvntdkZS%2Bu76dw9kQ%40mail.gmail.com.

[RIJU PATHROSE]

FTA

On Wed, 9 Feb 2022 at 06:18, Mohd Siraj <mohd...@gmail.com> wrote:

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-weld...@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/8e1f3a9f-2d27-44fa-b777-6a9e6ed119ddn%40googlegroups.com.

--

Best Regards,

Riju pathrose

QA/QC Engineer
Mob: +966558506746

[Tajuddin Mohammed]

You can use ERNICRMO-3 

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-weld...@googlegroups.com.

To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAHqH7yAQ5mG4ZSP1b8dm-3X7HWASTFGeuv0Y_s2hqR-qGHH2mw%40mail.gmail.com.