[MW:17330] Pipe joint resting on the beam
Weaver, mark
The pipe needs a “shoe” to prevent corrosion down the road…good luck!
Mark Weaver
UOP Callidus
--
To post to this group, send email to
material...@googlegroups.com
To unsubscribe from this group, send email to
materials-weld...@googlegroups.com
For more options, visit this group's bolg at
http://materials-welding.blogspot.com/
http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to
materials-weld...@googlegroups.com.
For more options, visit https://groups.google.com/groups/opt_out.
hwj...@tce.co.in
It certainly is not allowed as the weld joint is getting rested on the beam rather than the pipe itself. The beam is meant to support the pipe. Further, the elevation of the beams if they are being used as a resting support, are determined by the BOP of pipe for bare pipes.The weld joint projection is not going to occur at each support. As a result , wherever, the joint is not resting , a gap shall emerge between the BOP of pipe and TOS of the beam, which may be required to be filled . Since such dimensions of such gaps are not always in perfect digits, the possibility of imperfect filling crops up . As a result more load may occur on an adjacent support of such imperfectly filled pipe.
your truly
H W JOSHI
ENGINEER MECHANICAL
TATA CONSULTING ENGINEERS LTD
MUMBAI - 400 083
TEL : 022 61148409
| sumod s <sumod.sa...@gmail.com>
Sent by: material...@googlegroups.com 04/10/2013 03:25 PM
|
|
|
sir,
Please explain the basic reason for not permitting the practice as seen in attached photo.
sumod
--
To post to this group, send email to material...@googlegroups.com
To unsubscribe from this group, send email to materials-weld...@googlegroups.com
For more options, visit this group's bolg at
http://materials-welding.blogspot.com/
http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm
The views expressed/exchnaged in this group are members personel views
and meant for educational purposes only, Users must take their own decisions
w.r.t. applicable code/standard/contract documents.
---
You received this message because you are subscribed to the Google Groups
"Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send
an email to materials-weld...@googlegroups.com.
For more options, visit https://groups.google.com/groups/opt_out
.
[attachment "SAM_0690.jpg" deleted by hemant w joshi/ME/MC-Nuclear/TCE]
[attachment "SAM_0692.jpg" deleted by hemant w joshi/ME/MC-Nuclear/TCE]
----------------------------------------------------------------------------------------------------------
Information transmitted by this E-MAIL is intended only for the use of the addressee(s) and contains information that is privileged, confidential or exempt from disclosure under applicable law. If you are not the intended recipient or it appears that this mail has been forwarded to you without proper authority, you are notified that any use or dissemination and or copying of this email in any manner is strictly prohibited and you are requested to delete this e-mail immediately.
Communicating through e-mail is not secure and capable of interception and delays. Any one communicating with TATA Consulting Engineers Ltd., and / or its subsidiaries or associates or group companies by e-mail accepts the risks involved and their consequences.
While this e-mail has been checked for all known viruses, the addressee should also scan for viruses and notify the originator of e-mail.
---------------------------------------------------------------------------------------------------------
Jean Staton
My opinion is it is unsafe and because rain/moisture can accumulate on the beam it will lead to corrosion on the pipe. Also, visual inspection cannot be perform 100% when doing routine inspection.
Jean Staton
Corporate RSO
Quality, Safety, Environmental Manager
METCO - Materials Evaluation & Technology Corporation
27 Sawyer St, Beaumont, TX 77702
Phone: (409) 835-2600
Fax: (409) 835-1199
Cell: (409) 553-9460
Email: jean....@metco-ndt.com
Website: www.metco-ndt.com
From: material...@googlegroups.com [mailto:material...@googlegroups.com] On Behalf Of sumod s
Sent: Wednesday, April 10, 2013 4:55 AM
To: material...@googlegroups.com
Subject: [MW:17330] Pipe joint resting on the beam
sir,
Please explain the basic reason for not permitting the practice as seen in attached photo.
sumod
--
To post to this group, send email to
material...@googlegroups.com
To unsubscribe from this group, send email to
materials-weld...@googlegroups.com
For more options, visit this group's bolg at
http://materials-welding.blogspot.com/
http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to
materials-weld...@googlegroups.com.
For more options, visit https://groups.google.com/groups/opt_out.
DISCLAIMER: The information contained in this e-mail may be confidential and is intended solely for the use of the named addressee. Access, copying or re-use of the e-mail or any information contained therein by any other person is not authorized. If you are not the intended recipient please notify us immediately by returning the e-mail to the originator.
Eng.Mahmoud kamel
1- how can you check hydro test line check
2-how can painting apply
3-how can check joint during period inspection per year or two year
regards
Mahmoud
qc engineer
Date: Wed, 10 Apr 2013 12:54:55 +0300
Subject: [MW:17330] Pipe joint resting on the beam