nforce4 USB 2.0 problem
Bruce Burden
Hi folks,
Any suggestion on this issue:
Aug 21 19:22:21 tigerfish2 kernel: uhub1: device problem (SHORT_XFER), disabling port 6
Aug 21 19:22:50 tigerfish2 kernel: uhub1: device problem (SHORT_XFER), disabling port 6
Aug 21 19:23:02 tigerfish2 kernel: umass0: vendor 0x3538 USB Mass Storage Device, rev 2.00
/1.00, addr 4
Aug 21 19:23:02 tigerfish2 kernel: da3 at umass-sim0 bus 0 target 0 lun 0
Aug 21 19:23:02 tigerfish2 kernel: da3: <Generic USB Flash Disk 0.00> Removable Direct Acc
ess SCSI-2 device
Aug 21 19:23:02 tigerfish2 kernel: da3: 1.000MB/s transfers
Aug 21 19:23:02 tigerfish2 kernel: da3: 4000MB (8192000 512 byte sectors: 255H 63S/T 509C)
Aug 21 19:24:26 tigerfish2 kernel: umass0: at uhub0 port 5 (addr 4) disconnected
Aug 21 19:24:26 tigerfish2 kernel: (da3:umass-sim0:0:0:0): lost device
Aug 21 19:24:26 tigerfish2 kernel: (da3:umass-sim0:0:0:0): removing device entry
Aug 21 19:24:26 tigerfish2 kernel: umass0: detached
Aug 21 20:32:01 tigerfish2 kernel: uhub1: device problem (SHORT_XFER), disabling port 6
Aug 21 20:32:08 tigerfish2 kernel: uhub1: device problem (SHORT_XFER), disabling port 5
Aug 21 20:32:16 tigerfish2 kernel: uhub1: device problem (SHORT_XFER), disabling port 5
Aug 21 20:32:21 tigerfish2 kernel: uhub1: device problem (SHORT_XFER), disabling port 6
Aug 21 20:32:38 tigerfish2 kernel: uhub0: device problem (SET_ADDR_FAILED), disabling port
5
I was attempting to plub in my thumb drive with is UFS formatted. It
worked - once, as you can see above.
This is happening on a Tyan Thunder K8WE with the nForce
Professional chipset:
Aug 20 18:25:37 tigerfish2 kernel: ohci0: <OHCI (generic) USB controller> mem 0xa0000000-0
xa0000fff irq 20 at device 2.0 on pci0
Aug 20 18:25:37 tigerfish2 kernel: ohci0: [GIANT-LOCKED]
Aug 20 18:25:37 tigerfish2 kernel: usb0: OHCI version 1.0, legacy support
Aug 20 18:25:37 tigerfish2 kernel: usb0: SMM does not respond, resetting
Aug 20 18:25:37 tigerfish2 kernel: usb0: <OHCI (generic) USB controller> on ohci0
Aug 20 18:25:37 tigerfish2 kernel: usb0: USB revision 1.0
Aug 20 18:25:37 tigerfish2 kernel: uhub0: nVidia OHCI root hub, class 9/0, rev 1.00/1.00,
addr 1
Aug 20 18:25:37 tigerfish2 kernel: uhub0: 10 ports with 10 removable, self powered
Aug 20 18:25:37 tigerfish2 kernel: ehci0: <NVIDIA nForce4 USB 2.0 controller> mem 0xa00010
00-0xa00010ff irq 21 at device 2.1 on pci0
Aug 20 18:25:37 tigerfish2 kernel: ehci0: [GIANT-LOCKED]
Aug 20 18:25:37 tigerfish2 kernel: usb1: waiting for BIOS to give up control
Aug 20 18:25:37 tigerfish2 kernel: usb1: timed out waiting for BIOS
Aug 20 18:25:37 tigerfish2 kernel: usb1: EHCI version 1.0
Aug 20 18:25:37 tigerfish2 kernel: usb1: companion controller, 4 ports each: usb0
Aug 20 18:25:37 tigerfish2 kernel: usb1: <NVIDIA nForce4 USB 2.0 controller> on ehci0
Aug 20 18:25:37 tigerfish2 kernel: usb1: USB revision 2.0
Aug 20 18:25:37 tigerfish2 kernel: uhub1: nVidia EHCI root hub, class 9/0, rev 2.00/1.00,
addr 1
Aug 20 18:25:37 tigerfish2 kernel: uhub1: 10 ports with 10 removable, self powered
Aug 20 18:25:37 tigerfish2 kernel: umass0: Generic USB Storage Device, rev 2.00/1.00, addr
2
Things work in USB 1.0 mode, or after removing the echi device from the
kernel.
Bruce
--
------------------------------------------------------------------------
"I like bad!" Bruce Burden Austin, TX.
- Thuganlitha
The Power and the Prophet
Robert Don Hughes
Hans Petter Selasky
> Hi folks,
>
> Any suggestion on this issue:
>
I'm not sure if it helps, but could you have tried to install my new USB
driver, and see if the problem is the same:
#
# SVN is available from /usr/ports/devel/subversion
#
svn --username anonsvn --password anonsvn \
checkout svn://svn.turbocat.net/i4b
#
# The following commands will
# install the driver on FreeBSD:
#
cd i4b/trunk/i4b/FreeBSD.usb
make S=../src package
make install
#
# Then build a new kernel with "device ehci"
#
Yours
--HPS