Prosoft Unit 4

[Gaja Starks]

TheEtherNet/IP to PROFINET device gateway offers bi-directional data transfers between a PROFINET Controller and EtherNet/IP networks. The PLX32-EIP-PND gateway is a stand-alone DIN-rail mounted unit that provides two Ethernet ports, with each port using a different subnet.

The onboard SD Card slot (SD card optional) is used for storing configuration files that can be used for recovery, transferring the configuration to another gateway, or general configuration backup. The EtherNet/IP Driver uses Class 1 I/O connections or Class 3 Message instructions. The PROFINET driver operates as a PROFINET Class A device.

10/100Mbit RJ45 Connector Electrical Isolation 1500 Vrms at 50 Hz to 60 Hz for 60 seconds, applied as specified in section 5.3.2 of IEC 60950: 1991

Ethernet Broadcast Storm Resiliency = less than or equal to 5000 [ARP] frames-per-second and less than or equal to 5 minutes duration

Has anyone used a ProSoft AN-X4-AB-DHRIO to convert ethernet from iFix V3.5 SCADA to DH+ on SLC5/04 PLC's at all? We are looking to use this but have had some comments that the ProSoft unit can struggle with the quantity of data between SCADA and the SLC on DH+

The alternative is to use CLX and a DHRIO unit. Reluctant to go this route as the cost is extortionate and the DHRIO unit is now end of life. We can't change the SLC's out at the moment so need a cost effective alternative.

Huh. I'm not so sure this isn't just someone's disappointment with the DH+ data rates, which, even at its fastest, is multiple orders of magnitude slower than ethernet. The CLX/DHRIO combination won't go any faster, I would think. (My experiences with Prosoft devices are entirely positive, fwiw.)

One other observation is that it seem like the ignition TCP driver honors some security that the other Modbus devices don't. I can't write to an address until I login using the web page interface of the device. This is a problem because the manual explains that I need to login over modus to enable writes but I can't write to the registers that it wants me to write the password to.

Maybe because the "Span Gaps" setting (enabled by default) is combining them into a request for a range the device objects to, and by adding unique unit id you prevent that from happening. You're lucky this device just ignores unit id if that's it.

Intermediate Unit 1 is a regional educational agency that strives to provide educational support to the students, parents, educators, school administrators, and the communities throughout southwestern Pennsylvania.

HandPunch ProSoft is an industry leading time and attendance software that is used to automate the timekeeping of your company's workforce. Punches are entered at a HandPunch biometric time clock and HandPunch ProSoft communicates to the unit and downloads all of the transactions. The software then applies the pay rules (rounding, wages, schedules, etc.) that have been customized for your business. These rules are applied automatically, conistently, an impartially. It is designed for small to mid-size companies. Since the software is menu-driven, it is very intuitive and easy to master. No prior computer experience is necessary.

Listed below are some of the payroll software and providers that our time clock system can export data to. Even if your payroll software or provider is not listed, don't worry, we will most likely be able to export to them. Just give us a call to discuss.

Implementing a new technology for your business can be a daunting experience. It may even be scary to some. However, there is no reason to fear, the HandPunch Guys are here! We will take you by the hand and walk you through every step of the way. From choosing the right biometric time clock system to getting it implemented and getting you trained, we are here for you.

You won't believe how quickly and easily your company can be up and running with a time and attendance system that utilizes the latest technological advances that will save you money. So go ahead and give us a call today, it would be our pleasure to serve you.

In the initial phase of the upgrade process, particularly when transitioning from a MICROS(+) central unit, determining necessary hardware (TDS) components is essential. Utilize PROSOFT 4 for streamlined and efficient identification, thanks to its specialized features.

If your old central unit is a NANOS (TDS10200) or PICOS (TDS10009), the G2 to G3 migration is very easy. You can swap the old central unit with a new PALAS (TDS10300) or DOMUS (TDS10309) central unit. In addition to the hardware modification, simply open your old NBT file in the latest version of PROSOFT4 and transfer it to your new central unit.

If you want to upgrade from a MICROS (G1), you first must convert your old NBT file to the 2.80 PROSOFT. This is because PROSOFT 4.0 cannot read files from any PROSOFT version prior to 2.80. When you open your file in PROSOFT 4.0, it is automatically converted to a 'MICROS+' file.

PROSOFT will check first whether it is possible to convert the file to a DOMUS unit. If your file is small enough to convert, you will be asked if you want to convert it to a DOMUS or a PALAS. Otherwise, the file is immediately converted to a PALAS NBT file.

Therefore, if the file is suitable for conversion to DOMUS, you'll be presented with the option to choose between DOMUS or PALAS. If you opt for DOMUS, ensure that all your interfaces are on BUS1, as DOMUS supports only one BUS.

After your file is converted, you can conveniently verify in PROSOFT the necessary TDS hardware, though it's advisable to assess if any cleanup is feasible beforehand. Hence, understanding the conversion process could be beneficial.

You might look if this is the right choice, maybe you can better use this opportunity to use some TDS13634 or TDS13644. Depending on your choice, a rewiring may be necessary. Once you cleaned up you will see in the file how many TDS13510 and what dimmer interfaces you need to install.

As most of the installations are equipped with a iSGUI (mobile app) license, you will also need to activate the new ATMOS app on the new central unit. This is free of charge for four years after you obtained the iSGUI license.

Because you started from your original file your cloud ID is still the same. To replace the central unit in the cloud please follow these steps to update the central unit in TTCloud by using PROSOFT 4:

PRO-SOFT is the user-friendly operating environment for your CAD-PRO laser projection system. With a single platform, you can organize your daily work routine easily and efficiently. The software supports you from work preparation and managing projections, all the way through to documentation and quality assurance.

The Viewport function allows you to project sections (viewports) of complex projection files. With this function, only the part of the projection file that is relevant for production is projected. In the projection window you can drag a frame around the desired area via mouse click. Irrelevant parts of the projection are hidden. This can increase projection quality.

The context-sensitive help function offers short explanations and links to the requested topic in the manual. This allows the operator to directly call up the appropriate chapter for the current work step. The embedded help is also available in the PRO-SOFT Configuration.

At the factory, the laser projector is set to project contours with a high degree of accuracy. For some applications, high speed is more important than a high degree of accuracy. The laser projector can then project with a reduced degree of accuracy at a higher speed. As a result, the laser projection is perceived as more pleasant by the human eye.

An alternative to controlling the laser projector via the computer is operation via remote control and a projected menu. The software can project the menu, for example, right next to the projection surface or on a wall on the opposite side of the room. You can operate the software from any position and do not need to access the PRO-SOFT computer for each work step.

User management prevents unauthorized people from operating the projection system or changing the configuration. The software therefore provides the possibility to define the rights of users. User management can be used flexibly, making it possible e.g. to secure access to the software settings through a password-protected administrator account.

PRO-SOFT can operate in metric or imperial units. You can switch unit selection in a running system; no restart is required. You can also choose between a light or dark background, large or small toolbar buttons, and up to 12 languages.

PRO-SOFT TP is the standard software for all works on a plane surface in combination with height coordinates. The height level of the projection (Z-coordinates) can be changed manually. For recurrent height values, you can easily create buttons in the tool bar. Typical applications: wood and stone processing industries, prefab homes production, roof truss production and the precast concrete parts industry.

This software has been optimized for users in the precast concrete industry. You can import and display data in Unitechnik format. Unitechnik controls are displayed in the lower part of the screen. The software supports the production of double-wall and massive wall elements. Positions of reinforcements also can be shown.

For projection on 3D surfaces PRO-SOFT ST is the right choice. The single tasking version can control complex work areas with up to 16 projectors. More projectors can be connected with customized solutions. Projectors may be placed with offset to each other, turned by 90, facing each other or crosswise to cover contorted or twisted shapes.

3a8082e126