Google Groups no longer supports new Usenet posts or subscriptions. Historical content remains viewable.
Dismiss
Bug#1008760: upgrade-reports: Mouse touchpad elantech broken edge scrolling after upgrade to bullseye
1 view
Skip to first unread message
Paul Gevers
Apr 1, 2022, 1:40:03 PM4/1/22
to
Control: reassign -1 src:linux
Hi Umut,
After asking around, the suspicion is that this is mostly likely due to
the kernel, hence I'm reassigning to the linux source package. If this
was wrong, the kernel maintainers can hopefully help to point where it
should go.
Paul
On 31-03-2022 22:51, Umut Erdogan wrote:
> Package: upgrade-reports
> Severity: important
> Tags: upstream
>
> Hi debian maintainers!
>
> As by upgrading from buster to bullseye as also by using bullseye live image I
> have about 70% of touchpad width acting as edgescrolling area.
>
> I tried the debian 11 gnome and kde images and in both the same effect.
>
> At first I thought that the mouse would not work at all.
>
> But than I realized, that it just was in that area in scrolling mode.
>
> Only if I start to touch it at the remaining left area the mouse pointer worked
> as before.
>
> If I do so I can also swipe to the right most areas of the pad.
>
> That means that between buster and bullseye something got broken. Either from
> linux kernel or the firmware for elantech.
>
> So for now I switched back from bullseye to buster again until this gets fixed.
>
> Hope this happens until EOL of buster.
>
> Kind regards.
>
> Umut Erdogan
>
>
>
> -- System Information:
> Debian Release: 10.11
> APT prefers oldstable-updates
> APT policy: (500, 'oldstable-updates'), (500, 'oldstable')
> Architecture: amd64 (x86_64)
> Foreign Architectures: armhf, i386
>
> Kernel: Linux 4.19.0-19-amd64 (SMP w/8 CPU cores)
> Kernel taint flags: TAINT_OOT_MODULE, TAINT_UNSIGNED_MODULE
> Locale: LANG=de_DE.utf8, LC_CTYPE=de_DE.utf8 (charmap=UTF-8), LANGUAGE=de_DE.utf8 (charmap=UTF-8)
> Shell: /bin/sh linked to /bin/dash
> Init: systemd (via /run/systemd/system)
> LSM: AppArmor: enabled
Hi Umut,
After asking around, the suspicion is that this is mostly likely due to
the kernel, hence I'm reassigning to the linux source package. If this
was wrong, the kernel maintainers can hopefully help to point where it
should go.
Paul
On 31-03-2022 22:51, Umut Erdogan wrote:
> Package: upgrade-reports
> Severity: important
> Tags: upstream
>
> Hi debian maintainers!
>
> As by upgrading from buster to bullseye as also by using bullseye live image I
> have about 70% of touchpad width acting as edgescrolling area.
>
> I tried the debian 11 gnome and kde images and in both the same effect.
>
> At first I thought that the mouse would not work at all.
>
> But than I realized, that it just was in that area in scrolling mode.
>
> Only if I start to touch it at the remaining left area the mouse pointer worked
> as before.
>
> If I do so I can also swipe to the right most areas of the pad.
>
> That means that between buster and bullseye something got broken. Either from
> linux kernel or the firmware for elantech.
>
> So for now I switched back from bullseye to buster again until this gets fixed.
>
> Hope this happens until EOL of buster.
>
> Kind regards.
>
> Umut Erdogan
>
>
>
> -- System Information:
> Debian Release: 10.11
> APT prefers oldstable-updates
> APT policy: (500, 'oldstable-updates'), (500, 'oldstable')
> Architecture: amd64 (x86_64)
> Foreign Architectures: armhf, i386
>
> Kernel: Linux 4.19.0-19-amd64 (SMP w/8 CPU cores)
> Kernel taint flags: TAINT_OOT_MODULE, TAINT_UNSIGNED_MODULE
> Locale: LANG=de_DE.utf8, LC_CTYPE=de_DE.utf8 (charmap=UTF-8), LANGUAGE=de_DE.utf8 (charmap=UTF-8)
> Shell: /bin/sh linked to /bin/dash
> Init: systemd (via /run/systemd/system)
> LSM: AppArmor: enabled
0 new messages