Google Groups no longer supports new Usenet posts or subscriptions. Historical content remains viewable.
Dismiss
Bug#990428: ifenslave: Bonding not working on bullseye (using bond-slaves config)
2,296 views
Skip to first unread message
Claudio Kuenzler
Jun 28, 2021, 5:30:02 PM6/28/21
to
Package: ifenslave
Version: 2.12
Severity: important
Dear Maintainer,
Bonding on Debian 11 Bullseye is not working, when using "bond-slaves int1 int2" syntax on the bonding interface.
However it seems to work, when defining bonding the other way around using "bond-master bond1" on the interfaces which make up the bonding interface.
I came across bug #968368 and modified the ifenslave pre-up.d script, hence the changes below.
The same config (using bond-slaves) was working fine in Debian Buster. In Bullseye the bond interface stays DOWN and /proc/net/bonding/bond* also shows mii-status down.
-- System Information:
Debian Release: 11.0
APT prefers testing-security
APT policy: (500, 'testing-security'), (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 5.10.0-7-amd64 (SMP w/24 CPU threads)
Kernel taint flags: TAINT_FIRMWARE_WORKAROUND
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8), LANGUAGE=en_US:en
Shell: /bin/sh linked to /usr/bin/dash
Init: systemd (via /run/systemd/system)
LSM: AppArmor: enabled
Versions of packages ifenslave depends on:
ii ifupdown 0.8.36
ii iproute2 5.10.0-4
Versions of packages ifenslave recommends:
ii net-tools 1.60+git20181103.0eebece-1
ifenslave suggests no packages.
-- Configuration Files:
/etc/network/if-pre-up.d/ifenslave changed:
[ "$VERBOSITY" = 1 ] && set -x
[ "$ADDRFAM" = meta ] && exit 0
add_master()
{
# Return if $IFACE is already a bonding interface.
[ -f "/sys/class/net/$IFACE/bonding/slaves" ] && return
ip link add dev "$IFACE" type bond
}
sysfs_change_down()
{
# Called with :
# $1 = basename of the file in bonding/ to write to.
# $2 = value to write. Won't write if $2 is empty.
if [ -n "$2" ] ; then
# If the value we plan to write is different from the current one...
if ! grep -sq "\\<$2\\>" "/sys/class/net/$BOND_MASTER/bonding/$1" ; then
# ...and the master is up...
if ip link show "$BOND_MASTER" | grep -sq '[<,]UP[,>]' ; then
# ...bring the master down.
ip link set dev "$BOND_MASTER" down
fi
fi
sysfs "$1" "$2"
fi
}
sysfs()
{
# Called with :
# $1 = basename of the file in bonding/ to write to.
# $2 = value to write. Won't write if $2 is empty.
if [ -n "$2" ] ; then
echo "$2" > "/sys/class/net/$BOND_MASTER/bonding/$1"
return $?
fi
return 0
}
sysfs_add()
{
#??Called with :
# $1 = target filename.
# $2 = values to write.
for value in $2; do
# Do not add $2 to $1 if already present.
if ! grep -sq "\\<$value\\>" "/sys/class/net/$BOND_MASTER/bonding/$1"
then
sysfs "$1" "+$value"
fi
done
}
early_setup_master()
{
# Warning: the order in which we write into the sysfs files is important.
# Double check in drivers/net/bonding/bond_sysfs.c in the Linux kernel source tree
# before changing anything here.
# fail_over_mac must be set before enslavement of any slaves.
sysfs fail_over_mac "$IF_BOND_FAIL_OVER_MAC"
}
enslave_slaves()
{
case "$BOND_SLAVES" in
none)
BOND_SLAVES=""
;;
all)
BOND_SLAVES=$(sed -ne 's/ *\(eth[^:]*\):.*/\1/p' /proc/net/dev)
;;
esac
[ "$VERBOSITY" = 1 ] && v=-v
for slave in $BOND_SLAVES ; do
export IFENSLAVE_ENV_NAME="IFUPDOWN_$slave"
IFUPDOWN_IFACE="$(printenv "$IFENSLAVE_ENV_NAME")"
unset IFENSLAVE_ENV_NAME
#if ifquery --state "$slave" 2>/dev/null || [ -n "$IFUPDOWN_IFACE" ] ; then
if ifquery --state "$slave" 2>/dev/null ; then
# Skipping interface that's already up or being configured
continue
else
# Ensure $slave is down.
ip link set "$slave" down 2>/dev/null
if ! sysfs_add slaves "$slave" 2>/dev/null ; then
echo "Failed to enslave $slave to $BOND_MASTER. Is $BOND_MASTER ready and a bonding interface ?" >&2
else
# Bring up slave if it is the target of an allow-bondX stanza.
# This is useful to bring up slaves that need extra setup.
ifup $v --allow "$BOND_MASTER" "$slave"
fi
fi
done
}
setup_master()
{
# Warning: the order in which we write into the sysfs files is important.
# Double check in drivers/net/bonding/bond_sysfs.c in the Linux kernel source tree
# before changing anything here.
# use_carrier can be set anytime.
sysfs use_carrier "$IF_BOND_USE_CARRIER"
# num_grat_arp can be set anytime.
sysfs num_grat_arp "$IF_BOND_NUM_GRAT_ARP"
# num_unsol_na can be set anytime.
sysfs num_unsol_na "$IF_BOND_NUM_UNSOL_NA"
# arp_ip_target must be set before arp_interval.
sysfs_add arp_ip_target "$IF_BOND_ARP_IP_TARGET"
sysfs arp_interval "$IF_BOND_ARP_INTERVAL"
# miimon must be set before updelay and downdelay.
sysfs miimon "$IF_BOND_MIIMON"
sysfs downdelay "$IF_BOND_DOWNDELAY"
sysfs updelay "$IF_BOND_UPDELAY"
# Changing ad_select requires $BOND_MASTER to be down.
sysfs_change_down ad_select "$IF_BOND_AD_SELECT"
# Changing mode requires $BOND_MASTER to be down.
# Mode should be set after miimon or arp_interval, to avoid a warning in syslog.
sysfs_change_down mode "$IF_BOND_MODE"
# Requires $BOND_MASTER to be down and mode to be configured
sysfs_change_down xmit_hash_policy "$IF_BOND_XMIT_HASH_POLICY"
sysfs_change_down tlb_dynamic_lb "$IF_BOND_TLB_DYNAMIC_LB"
# packets_per_slave allowed for mode balance-rr only.
sysfs packets_per_slave "$IF_BOND_PACKETS_PER_SLAVE"
# arp_validate must be after mode (because mode must be active-backup).
sysfs arp_validate "$IF_BOND_ARP_VALIDATE"
# lacp_rate must be set after mode (because mode must be 802.3ad).
# Changing lacp_rate requires $BOND_MASTER to be down.
sysfs_change_down lacp_rate "$IF_BOND_LACP_RATE"
# queue_id must be set after enslavement.
for iface_queue_id in $IF_BOND_QUEUE_ID ; do
sysfs iface_queue_id "$iface_queue_id"
done
# active_slave must be set after mode and after enslavement.
# The slave must be up and the underlying link must be up too.
# FIXME: We should have a way to write an empty string to active_slave, to set the active_slave to none.
if [ -n "$IF_BOND_ACTIVE_SLAVE" ] ; then
if [ "$IF_BOND_ACTIVE_SLAVE" = "none" ] ; then
sysfs active_slave ""
else
# Need to force interface up before. Bonding will refuse to activate a down interface.
if ifquery -l "$IF_BOND_ACTIVE_SLAVE" 2>/dev/null ; then
ifup "$IF_BOND_ACTIVE_SLAVE"
else
ip link set "$IF_BOND_ACTIVE_SLAVE" up
fi
sysfs active_slave "$IF_BOND_ACTIVE_SLAVE"
fi
fi
}
setup_primary() {
# primary must be set after mode (because only supported in some modes) and after enslavement.
# The first slave in bond-primary found in current slaves becomes the primary.
# If no slave in bond-primary is found, then the primary does not change.
for slave in $IF_BOND_PRIMARY ; do
slaves="/sys/class/net/$BOND_MASTER/bonding/slaves"
if grep -sq "\\<$slave\\>" "$slaves" ; then
sysfs primary "$slave"
break
fi
done
# primary_reselect should be set after mode (it is only supported in some modes), after enslavement
# and after primary. This is currently (2.6.35-rc1) not enforced by the bonding driver, but it is
# probably safer to do it in that order.
sysfs primary_reselect "$IF_BOND_PRIMARY_RESELECT"
}
setup_master_device() {
add_master
early_setup_master
setup_master
enslave_slaves
setup_primary
}
setup_slave_device() {
# Require the bond master to have an iface stanza
#if ! ifstate -l "$IF_BOND_MASTER" 2>/dev/null ; then
if ! ifquery -l "$IF_BOND_MASTER" 2>&1 >/dev/null ; then
echo "No iface stanza found for master $IF_BOND_MASTER" >&2
exit 1
fi
# Ensure the master is up or being configured
export IFENSLAVE_ENV_NAME="IFUPDOWN_$IF_BOND_MASTER"
IFUPDOWN_IF_BOND_MASTER="$(printenv "$IFENSLAVE_ENV_NAME")"
unset IFENSLAVE_ENV_NAME
if [ -z "$IFUPDOWN_IF_BOND_MASTER" ] ; then
#ifquery --state "$IF_BOND_MASTER" 2>/dev/null || ifup "$IF_BOND_MASTER"
ifquery --state "$IF_BOND_MASTER" 2>&1 >/dev/null || ifup "$IF_BOND_MASTER"
fi
# Enslave it to the master
#ip link set "$slave" down 2>/dev/null
#if ! sysfs_add slaves "$slave" 2>/dev/null ; then
# echo "Failed to enslave $slave to $BOND_MASTER." >&2
ip link set "$1" down 2>/dev/null
if ! sysfs_add slaves "$1" 2>/dev/null ; then
echo "Failed to enslave $1 to $BOND_MASTER." >&2
fi
setup_primary
}
IF_BOND_SLAVES=${IF_BOND_SLAVES:-$IF_SLAVES}
if [ -n "$IF_BOND_MASTER" ] ; then
# FIXME: use function arguments instead of this variable
BOND_MASTER="$IF_BOND_MASTER"
setup_slave_device "$IFACE"
elif [ -n "$IF_BOND_SLAVES" ] || [ -n "$IF_BOND_MODE" ] ; then
# FIXME: use function arguments instead of these variables
BOND_MASTER="$IFACE"
BOND_SLAVES="$IF_BOND_SLAVES"
setup_master_device "$IFACE"
fi
exit 0
-- no debconf information
Version: 2.12
Severity: important
Dear Maintainer,
Bonding on Debian 11 Bullseye is not working, when using "bond-slaves int1 int2" syntax on the bonding interface.
However it seems to work, when defining bonding the other way around using "bond-master bond1" on the interfaces which make up the bonding interface.
I came across bug #968368 and modified the ifenslave pre-up.d script, hence the changes below.
The same config (using bond-slaves) was working fine in Debian Buster. In Bullseye the bond interface stays DOWN and /proc/net/bonding/bond* also shows mii-status down.
-- System Information:
Debian Release: 11.0
APT prefers testing-security
APT policy: (500, 'testing-security'), (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 5.10.0-7-amd64 (SMP w/24 CPU threads)
Kernel taint flags: TAINT_FIRMWARE_WORKAROUND
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8), LANGUAGE=en_US:en
Shell: /bin/sh linked to /usr/bin/dash
Init: systemd (via /run/systemd/system)
LSM: AppArmor: enabled
Versions of packages ifenslave depends on:
ii ifupdown 0.8.36
ii iproute2 5.10.0-4
Versions of packages ifenslave recommends:
ii net-tools 1.60+git20181103.0eebece-1
ifenslave suggests no packages.
-- Configuration Files:
/etc/network/if-pre-up.d/ifenslave changed:
[ "$VERBOSITY" = 1 ] && set -x
[ "$ADDRFAM" = meta ] && exit 0
add_master()
{
# Return if $IFACE is already a bonding interface.
[ -f "/sys/class/net/$IFACE/bonding/slaves" ] && return
ip link add dev "$IFACE" type bond
}
sysfs_change_down()
{
# Called with :
# $1 = basename of the file in bonding/ to write to.
# $2 = value to write. Won't write if $2 is empty.
if [ -n "$2" ] ; then
# If the value we plan to write is different from the current one...
if ! grep -sq "\\<$2\\>" "/sys/class/net/$BOND_MASTER/bonding/$1" ; then
# ...and the master is up...
if ip link show "$BOND_MASTER" | grep -sq '[<,]UP[,>]' ; then
# ...bring the master down.
ip link set dev "$BOND_MASTER" down
fi
fi
sysfs "$1" "$2"
fi
}
sysfs()
{
# Called with :
# $1 = basename of the file in bonding/ to write to.
# $2 = value to write. Won't write if $2 is empty.
if [ -n "$2" ] ; then
echo "$2" > "/sys/class/net/$BOND_MASTER/bonding/$1"
return $?
fi
return 0
}
sysfs_add()
{
#??Called with :
# $1 = target filename.
# $2 = values to write.
for value in $2; do
# Do not add $2 to $1 if already present.
if ! grep -sq "\\<$value\\>" "/sys/class/net/$BOND_MASTER/bonding/$1"
then
sysfs "$1" "+$value"
fi
done
}
early_setup_master()
{
# Warning: the order in which we write into the sysfs files is important.
# Double check in drivers/net/bonding/bond_sysfs.c in the Linux kernel source tree
# before changing anything here.
# fail_over_mac must be set before enslavement of any slaves.
sysfs fail_over_mac "$IF_BOND_FAIL_OVER_MAC"
}
enslave_slaves()
{
case "$BOND_SLAVES" in
none)
BOND_SLAVES=""
;;
all)
BOND_SLAVES=$(sed -ne 's/ *\(eth[^:]*\):.*/\1/p' /proc/net/dev)
;;
esac
[ "$VERBOSITY" = 1 ] && v=-v
for slave in $BOND_SLAVES ; do
export IFENSLAVE_ENV_NAME="IFUPDOWN_$slave"
IFUPDOWN_IFACE="$(printenv "$IFENSLAVE_ENV_NAME")"
unset IFENSLAVE_ENV_NAME
#if ifquery --state "$slave" 2>/dev/null || [ -n "$IFUPDOWN_IFACE" ] ; then
if ifquery --state "$slave" 2>/dev/null ; then
# Skipping interface that's already up or being configured
continue
else
# Ensure $slave is down.
ip link set "$slave" down 2>/dev/null
if ! sysfs_add slaves "$slave" 2>/dev/null ; then
echo "Failed to enslave $slave to $BOND_MASTER. Is $BOND_MASTER ready and a bonding interface ?" >&2
else
# Bring up slave if it is the target of an allow-bondX stanza.
# This is useful to bring up slaves that need extra setup.
ifup $v --allow "$BOND_MASTER" "$slave"
fi
fi
done
}
setup_master()
{
# Warning: the order in which we write into the sysfs files is important.
# Double check in drivers/net/bonding/bond_sysfs.c in the Linux kernel source tree
# before changing anything here.
# use_carrier can be set anytime.
sysfs use_carrier "$IF_BOND_USE_CARRIER"
# num_grat_arp can be set anytime.
sysfs num_grat_arp "$IF_BOND_NUM_GRAT_ARP"
# num_unsol_na can be set anytime.
sysfs num_unsol_na "$IF_BOND_NUM_UNSOL_NA"
# arp_ip_target must be set before arp_interval.
sysfs_add arp_ip_target "$IF_BOND_ARP_IP_TARGET"
sysfs arp_interval "$IF_BOND_ARP_INTERVAL"
# miimon must be set before updelay and downdelay.
sysfs miimon "$IF_BOND_MIIMON"
sysfs downdelay "$IF_BOND_DOWNDELAY"
sysfs updelay "$IF_BOND_UPDELAY"
# Changing ad_select requires $BOND_MASTER to be down.
sysfs_change_down ad_select "$IF_BOND_AD_SELECT"
# Changing mode requires $BOND_MASTER to be down.
# Mode should be set after miimon or arp_interval, to avoid a warning in syslog.
sysfs_change_down mode "$IF_BOND_MODE"
# Requires $BOND_MASTER to be down and mode to be configured
sysfs_change_down xmit_hash_policy "$IF_BOND_XMIT_HASH_POLICY"
sysfs_change_down tlb_dynamic_lb "$IF_BOND_TLB_DYNAMIC_LB"
# packets_per_slave allowed for mode balance-rr only.
sysfs packets_per_slave "$IF_BOND_PACKETS_PER_SLAVE"
# arp_validate must be after mode (because mode must be active-backup).
sysfs arp_validate "$IF_BOND_ARP_VALIDATE"
# lacp_rate must be set after mode (because mode must be 802.3ad).
# Changing lacp_rate requires $BOND_MASTER to be down.
sysfs_change_down lacp_rate "$IF_BOND_LACP_RATE"
# queue_id must be set after enslavement.
for iface_queue_id in $IF_BOND_QUEUE_ID ; do
sysfs iface_queue_id "$iface_queue_id"
done
# active_slave must be set after mode and after enslavement.
# The slave must be up and the underlying link must be up too.
# FIXME: We should have a way to write an empty string to active_slave, to set the active_slave to none.
if [ -n "$IF_BOND_ACTIVE_SLAVE" ] ; then
if [ "$IF_BOND_ACTIVE_SLAVE" = "none" ] ; then
sysfs active_slave ""
else
# Need to force interface up before. Bonding will refuse to activate a down interface.
if ifquery -l "$IF_BOND_ACTIVE_SLAVE" 2>/dev/null ; then
ifup "$IF_BOND_ACTIVE_SLAVE"
else
ip link set "$IF_BOND_ACTIVE_SLAVE" up
fi
sysfs active_slave "$IF_BOND_ACTIVE_SLAVE"
fi
fi
}
setup_primary() {
# primary must be set after mode (because only supported in some modes) and after enslavement.
# The first slave in bond-primary found in current slaves becomes the primary.
# If no slave in bond-primary is found, then the primary does not change.
for slave in $IF_BOND_PRIMARY ; do
slaves="/sys/class/net/$BOND_MASTER/bonding/slaves"
if grep -sq "\\<$slave\\>" "$slaves" ; then
sysfs primary "$slave"
break
fi
done
# primary_reselect should be set after mode (it is only supported in some modes), after enslavement
# and after primary. This is currently (2.6.35-rc1) not enforced by the bonding driver, but it is
# probably safer to do it in that order.
sysfs primary_reselect "$IF_BOND_PRIMARY_RESELECT"
}
setup_master_device() {
add_master
early_setup_master
setup_master
enslave_slaves
setup_primary
}
setup_slave_device() {
# Require the bond master to have an iface stanza
#if ! ifstate -l "$IF_BOND_MASTER" 2>/dev/null ; then
if ! ifquery -l "$IF_BOND_MASTER" 2>&1 >/dev/null ; then
echo "No iface stanza found for master $IF_BOND_MASTER" >&2
exit 1
fi
# Ensure the master is up or being configured
export IFENSLAVE_ENV_NAME="IFUPDOWN_$IF_BOND_MASTER"
IFUPDOWN_IF_BOND_MASTER="$(printenv "$IFENSLAVE_ENV_NAME")"
unset IFENSLAVE_ENV_NAME
if [ -z "$IFUPDOWN_IF_BOND_MASTER" ] ; then
#ifquery --state "$IF_BOND_MASTER" 2>/dev/null || ifup "$IF_BOND_MASTER"
ifquery --state "$IF_BOND_MASTER" 2>&1 >/dev/null || ifup "$IF_BOND_MASTER"
fi
# Enslave it to the master
#ip link set "$slave" down 2>/dev/null
#if ! sysfs_add slaves "$slave" 2>/dev/null ; then
# echo "Failed to enslave $slave to $BOND_MASTER." >&2
ip link set "$1" down 2>/dev/null
if ! sysfs_add slaves "$1" 2>/dev/null ; then
echo "Failed to enslave $1 to $BOND_MASTER." >&2
fi
setup_primary
}
IF_BOND_SLAVES=${IF_BOND_SLAVES:-$IF_SLAVES}
if [ -n "$IF_BOND_MASTER" ] ; then
# FIXME: use function arguments instead of this variable
BOND_MASTER="$IF_BOND_MASTER"
setup_slave_device "$IFACE"
elif [ -n "$IF_BOND_SLAVES" ] || [ -n "$IF_BOND_MODE" ] ; then
# FIXME: use function arguments instead of these variables
BOND_MASTER="$IFACE"
BOND_SLAVES="$IF_BOND_SLAVES"
setup_master_device "$IFACE"
fi
exit 0
-- no debconf information
Claudio Kuenzler
Jun 29, 2021, 1:30:04 AM6/29/21
to
Non-working bonding config in /etc/network/interfaces:
auto enp4s0f0
iface enp4s0f0 inet manual
auto enp4s0f1
iface enp4s0f1 inet manual
auto bond1
iface bond1 inet static
address 192.168.12.4/24
gateway 192.168.12.1
slaves enp4s0f0 enp4s0f1
bond-mode 802.3ad
bond-miimon 100
bond-downdelay 200
bond-updelay 200
iface enp4s0f0 inet manual
auto enp4s0f1
iface enp4s0f1 inet manual
auto bond1
iface bond1 inet static
address 192.168.12.4/24
gateway 192.168.12.1
slaves enp4s0f0 enp4s0f1
bond-mode 802.3ad
bond-miimon 100
bond-downdelay 200
bond-updelay 200
(also mentioned in https://wiki.debian.org/Bonding)
Working config:
auto enp4s0f0
iface enp4s0f0 inet manual
bond-master bond1
auto enp4s0f1
iface enp4s0f1 inet manual
bond-master bond1
auto bond1
iface bond1 inet static
address 192.168.12.4/24
gateway 192.168.12.1
bond-slaves none
bond-mode 802.3ad
bond-miimon 100
bond-downdelay 200
bond-updelay 200
iface enp4s0f0 inet manual
bond-master bond1
auto enp4s0f1
iface enp4s0f1 inet manual
bond-master bond1
auto bond1
iface bond1 inet static
address 192.168.12.4/24
gateway 192.168.12.1
bond-slaves none
bond-mode 802.3ad
bond-miimon 100
bond-downdelay 200
bond-updelay 200
Claudio Kuenzler
Sep 1, 2021, 10:40:03 AM9/1/21
to
> In your case you could simply remove the stanzas for enp4s0f0 and enp4s0f1 which would leave you with just the stanza for bond1:
> iface bond1 inet static
> bond-slaves enp4s0f0 enp4s0f1
Thank you Oleander. It works with this hint (the physical interfaces
were left out of the config).
Working config:
=====================================================
ck@bullseye:~$ cat /etc/network/interfaces
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
source /etc/network/interfaces.d/*
# The loopback network interface
auto lo
iface lo inet loopback
auto bond0
iface bond0 inet static
address 192.168.12.4/24
gateway 192.168.12.1
bond-slaves enp3s0f0 enp3s0f1
bond-mode 802.3ad
bond-miimon 100
bond-lacp-rate 1
=====================================================
> That should work but it is still a regression as it breaks configuration which worked before.
Yes, agree. Do you know if your patch (I have not tested) will be
included in the next point release?
> https://serverfault.com/a/1075192/267378
>
> Best regards,
> Arunas
You mention both bond-master of the physical devices and blond-slaves
on the bond interface. This causes networking service to hiccup in my
case:
Sep 01 15:58:23 irczsrvp09 systemd[1]: Starting Raise network interfaces...
Sep 01 15:58:23 irczsrvp09 ifup[1251]: No iface stanza found for master bond0
Sep 01 15:58:23 irczsrvp09 ifup[1249]: run-parts:
/etc/network/if-pre-up.d/ifenslave exited with return code 1
Sep 01 15:58:23 irczsrvp09 ifup[1242]: ifup: failed to bring up enp3s0f0
Sep 01 15:58:23 irczsrvp09 ifup[1256]: No iface stanza found for master bond0
Sep 01 15:58:23 irczsrvp09 ifup[1254]: run-parts:
/etc/network/if-pre-up.d/ifenslave exited with return code 1
Sep 01 15:58:23 irczsrvp09 ifup[1242]: ifup: failed to bring up enp3s0f1
Sep 01 15:58:23 irczsrvp09 ifup[1261]: No iface stanza found for master bond1
Sep 01 15:58:23 irczsrvp09 ifup[1259]: run-parts:
/etc/network/if-pre-up.d/ifenslave exited with return code 1
Sep 01 15:58:23 irczsrvp09 ifup[1242]: ifup: failed to bring up enp4s0f0
Sep 01 15:58:23 irczsrvp09 ifup[1266]: No iface stanza found for master bond1
Sep 01 15:58:23 irczsrvp09 ifup[1264]: run-parts:
/etc/network/if-pre-up.d/ifenslave exited with return code 1
Sep 01 15:58:23 irczsrvp09 ifup[1242]: ifup: failed to bring up enp4s0f1
Although the bonding interface seems to work with your workaround, the
Systemd service (networking) is stuck at failed state.
So for now the "proper" way to fix this seems to be to remove the
physical device stanzas and only use the bonding interfaces - until
this bug is fixed.
> iface bond1 inet static
> bond-slaves enp4s0f0 enp4s0f1
Thank you Oleander. It works with this hint (the physical interfaces
were left out of the config).
Working config:
=====================================================
ck@bullseye:~$ cat /etc/network/interfaces
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
source /etc/network/interfaces.d/*
# The loopback network interface
auto lo
iface lo inet loopback
auto bond0
iface bond0 inet static
address 192.168.12.4/24
gateway 192.168.12.1
bond-slaves enp3s0f0 enp3s0f1
bond-mode 802.3ad
bond-miimon 100
bond-lacp-rate 1
=====================================================
> That should work but it is still a regression as it breaks configuration which worked before.
Yes, agree. Do you know if your patch (I have not tested) will be
included in the next point release?
> https://serverfault.com/a/1075192/267378
>
> Best regards,
> Arunas
You mention both bond-master of the physical devices and blond-slaves
on the bond interface. This causes networking service to hiccup in my
case:
Sep 01 15:58:23 irczsrvp09 systemd[1]: Starting Raise network interfaces...
Sep 01 15:58:23 irczsrvp09 ifup[1251]: No iface stanza found for master bond0
Sep 01 15:58:23 irczsrvp09 ifup[1249]: run-parts:
/etc/network/if-pre-up.d/ifenslave exited with return code 1
Sep 01 15:58:23 irczsrvp09 ifup[1242]: ifup: failed to bring up enp3s0f0
Sep 01 15:58:23 irczsrvp09 ifup[1256]: No iface stanza found for master bond0
Sep 01 15:58:23 irczsrvp09 ifup[1254]: run-parts:
/etc/network/if-pre-up.d/ifenslave exited with return code 1
Sep 01 15:58:23 irczsrvp09 ifup[1242]: ifup: failed to bring up enp3s0f1
Sep 01 15:58:23 irczsrvp09 ifup[1261]: No iface stanza found for master bond1
Sep 01 15:58:23 irczsrvp09 ifup[1259]: run-parts:
/etc/network/if-pre-up.d/ifenslave exited with return code 1
Sep 01 15:58:23 irczsrvp09 ifup[1242]: ifup: failed to bring up enp4s0f0
Sep 01 15:58:23 irczsrvp09 ifup[1266]: No iface stanza found for master bond1
Sep 01 15:58:23 irczsrvp09 ifup[1264]: run-parts:
/etc/network/if-pre-up.d/ifenslave exited with return code 1
Sep 01 15:58:23 irczsrvp09 ifup[1242]: ifup: failed to bring up enp4s0f1
Although the bonding interface seems to work with your workaround, the
Systemd service (networking) is stuck at failed state.
So for now the "proper" way to fix this seems to be to remove the
physical device stanzas and only use the bonding interfaces - until
this bug is fixed.
Frank Liu
Mar 14, 2022, 7:30:04 PM3/14/22
to
Hi,
I see Bullseye 11.3 is planned to release in two weeks:
https://lists.debian.org/debian-project/2022/03/msg00015.html
Is there a chance the fixed ifenslave version 2.13 be added?
I see Bullseye 11.3 is planned to release in two weeks:
https://lists.debian.org/debian-project/2022/03/msg00015.html
Is there a chance the fixed ifenslave version 2.13 be added?
Frank Liu
Mar 31, 2022, 1:10:03 AM3/31/22
to
Debian 11.3 was released over the weekend, and the ifenslave fix in this bug report is still not included.
0 new messages