Re: [Fwd: Re: [Osd 46] Embinux android binary porting problem]
amarnath
Everything is fine
May be your mmc card giving the problem
Try the uImage and rootfs by formatting once again mmc card into two
partitions.
Thanks & Regards,
Amarnath Alamuri
Partha wrote:
> FYI
>
>
> ------------------------------------------------------------------------
>
> Subject:
> Re: [Osd 46] Embinux android binary porting problem
> From:
> Jooil Park <jooi...@eepeesol.com>
> Date:
> Wed, 17 Feb 2010 18:59:47 +0900
> To:
> Partha <partha....@embinux.com>
>
> To:
> Partha <partha....@embinux.com>
>
>
> Partha,
>
> Thanks for the prompt reply.
>
> Yes, I correctly partitioned the vfat and ext3. I used to do it
> because I have installed angstrom, ubuntu lxde and xbuntu ect.
>
> Yes, U correctly positioned vfat (correct copy order in vfat , MLO
> fist u-boot.bin and uImage last) and rfs in ext3.
>
> I missed one impotant info in the previous mail.
> My beagle is C2 version and host machine is x86(32bit) ubuntu9.04.
>
> Regards
> Jooil
>
>
>
>
> 2010/2/17 Partha <partha....@embinux.com
> <mailto:partha....@embinux.com>>
>
> Jooil,
>
> Thanks for your interest on Embinux.
>
> After studying your error-log, I need to clarify some points like :
> 1) are you using two partitions in your mmc card .
> 2) two partitions should be vfat and ext3, where uImage should be
> in the vfat and rfs in the ext3 partition respectively.
>
> Regards
> Partha
>
> Jooil Park wrote:
>
> Hello Sirs,
>
> It's my honor to learn your esteemed organization via
> beagleboard.org <http://beagleboard.org>
> <http://beagleboard.org>.
>
> I am working hard on beagle board and android these days.
> EEPEE Solution is highly determined would-be embedded solution
> provider in Korea.
>
> I downloaded your Android on Beagle Binaries from your labs'
> main (pagehttp://labs.embinux.org/index.php/Main_Page
> <http://labs.embinux.org/index.php/Main_Page>
> <http://labs.embinux.org/index.php/Main_Page>) and copied all
> the files (RFS, UIMAGE) and set the environment in the u-boot
> command prompt according to the README file. But I couldn't
> boot android OS, it was hang up even I waited over 4 hours.
> Belows are boot message attained through cutecom(serial
> communication program). My host machine is ubuntu 9.04.
>
>
> Could you possibly verify the message and address my problem?
> I appreciate your kind help in advance and longing to hearing
> from you soon.
>
> Best Regards,
>
> Jooil Park / EEPEE Solution Co., Ltd.
> jooi...@eepeesol.com <mailto:jooi...@eepeesol.com>
> <mailto:jooi...@eepeesol.com
> <mailto:jooi...@eepeesol.com>> Mobile : 010-6432-8498
>
>
> -----------------------------------------------------------------------------------------------------------------------------------------------------------
> \0x00\0x04\0x01\0x05\0x0140\0x07V\0x13\0x02\0x01\0x00\0x12\0x15\0x01\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x14\0x15\0x01\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00\0x00
>
> Texas Instruments X-Loader 1.41
> Starting on with MMC
> Reading boot sector
>
> 180776 Bytes Read from MMC
> Starting OS Bootloader from MMC...
>
>
> U-Boot 2009.06-rc2 (Jun 05 2009 - 10:19:13)
>
> OMAP3530-GP ES3.0, CPU-OPP2 L3-165MHz
> OMAP3 Beagle board + LPDDR/NAND
> DRAM: 256 MB
> NAND: 256 MiB
> *** Warning - bad CRC or NAND, using default environment
>
> In: serial
> Out: serial
> Err: serial
> Board revision C
> Die ID #5f5000030000000004013f7906006017
> Hit any key to stop autoboot: 10 \0x08\0x08\0x08 9
> \0x08\0x08\0x08 8 \0x08\0x08\0x08 7 \0x08\0x08\0x08 0
> OMAP3 beagleboard.org <http://beagleboard.org>
> <http://beagleboard.org> # setenv bootargs
> console=ttyS2,115200n8 noinitrd root=/dev/mmcblk0p2
> video=omapfb.mode=dvi:1280x720MR-24@50 init=/init
> rootfstype=ext3 rw rootdelay=1 nohz=off androidboot..console=ttyS2
> OMAP3 beagleboard.org <http://beagleboard.org>
> <http://beagleboard.org> # mmcinit
>
> Unknown command 'mmcinit' - try 'help'
> OMAP3 beagleboard.org <http://beagleboard.org>
> <http://beagleboard.org> # mmc init
> mmc1 is available
> OMAP3 beagleboard.org <http://beagleboard.org>
> <http://beagleboard.org> # fatload mmc 0 0x80300000 uImage
>
> reading uImage
>
> 1911468 bytes read
> OMAP3 beagleboard.org <http://beagleboard.org>
> <http://beagleboard.org> # bootm 0x80300000
>
> ## Booting kernel from Legacy Image at 80300000 ...
> Image Name: Linux-2.6.29-omap1-07182-gc3b6e5
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 1911404 Bytes = 1.8 MB
> Load Address: 80008000
> Entry Point: 80008000
> Verifying Checksum ... OK
> Loading Kernel Image ... OK
> OK
>
> Starting kernel ...
>
> Uncompressing
> Linux............................................................................................................................
> done, booting the kernel.
> Linux version 2.6.29-omap1-07182-gc3b6e50
> (rupesh@rupesh-desktop) (gcc version 4.2.1 (CodeSourcery
> Sourcery G++ Lite 2007q3-51)) #1 Fri Jun 19 12:39:22 IST 2009
> CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c5387f
> CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction
> cache
> Machine: OMAP3 Beagle Board
> Memory policy: ECC disabled, Data cache writeback
> OMAP3430 ES3.0
> SRAM: Mapped pa 0x40200000 to va 0xd7000000 size: 0x100000
> Reserving 12582912 bytes SDRAM for VRAM
> Built 1 zonelists in Zone order, mobility grouping on. Total
> pages: 65024
> Kernel command line: console=ttyS2,115200n8 noinitrd
> root=/dev/mmcblk0p2 video=omapfb.mode=dvi:1280x720MR-24@50
> init=/init rootfstype=ext3 rw rootdelay=1 nohz=off
> androidboot.console=ttyS2
> Unknown boot option `androidboot.console=ttyS2': ignoring
> Clocking rate (Crystal/DPLL/ARM core): 26.0/332/500 MHz
> GPMC revision 5.0
> IRQ: Found an INTC at 0xd8200000 (revision 4.0) with 96 interrupts
> Total of 96 interrupts on 1 active controller
> OMAP34xx GPIO hardware version 2.5
> PID hash table entries: 1024 (order: 10, 4096 bytes)
> OMAP clockevent source: GPTIMER12 at 32768 Hz
> Console: colour dummy device 80x30
> Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
> Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
> Memory: 128MB 128MB = 256MB total
> Memory: 243072KB available (3496K code, 687K data, 140K init)
> Calibrating delay loop... 500.97 BogoMIPS (lpj=1953792)
> Mount-cache hash table entries: 512
> CPU: Testing write buffer coherency: ok
> net_namespace: 520 bytes
> regulator: core version 0.5
> NET: Registered protocol family 16
> Found NAND on CS0
> Registering NAND on CS0
> OMAP DMA hardware revision 4.0
> bio: create slab <bio-0> at 0
> OMAP DSS rev 2.0
> OMAP DISPC rev 3.0
> OMAP VENC rev 2
> i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
> twl4030: PIH (irq 7) chaining IRQs 368..375
> twl4030: power (irq 373) chaining IRQs 376..383
> twl4030: gpio (irq 368) chaining IRQs 384..401
> regulator: VMMC1: 1850 <--> 3150 mV normal standby
> regulator: VDAC: 1800 mV normal standby
> regulator: VUSB1V5: 1500 <--> 0 mV normal standby
> regulator: VUSB1V8: 1800 <--> 0 mV normal standby
> regulator: VUSB3V1: 3100 <--> 0 mV normal standby
> regulator: VPLL2: 1800 mV normal standby
> regulator: VSIM: 1800 <--> 3000 mV normal standby
> i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz
> SCSI subsystem initialized
> twl4030_usb twl4030_usb: Initialized TWL4030 USB module
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
> musb_hdrc: USB OTG mode controller at d80ab000 using DMA, IRQ 92
> NET: Registered protocol family 2
> IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
> TCP established hash table entries: 8192 (order: 4, 65536 bytes)
> TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
> TCP: Hash tables configured (established 8192 bind 8192)
> TCP reno registered
> NET: Registered protocol family 1
> NetWinder Floating Point Emulator V0.97 (double precision)
> ashmem: initialized
> VFS: Disk quotas dquot_6.5.2
> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> JFFS2 version 2.2. (NAND) \0xc2\0xa9 2001-2006 Red Hat, Inc.
> msgmni has been set to 475
> alg: No test for stdrng (krng)
> io scheduler noop registered
> io scheduler anticipatory registered (default)
> io scheduler deadline registered
> io scheduler cfq registered
> Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
> serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
> serial8250.0: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
> serial8250.0: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
> console [ttyS2] enabled
> brd: module loaded
> loop: module loaded
> i2c /dev entries driver
> Driver 'sd' needs updating - please use bus_type methods
> omap2-nand driver initializing
> NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND
> 256MiB 1,8V 16-bit)
> cmdlinepart partition parsing not available
> Creating 5 MTD partitions on "omap2-nand":
> 0x000000000000-0x000000080000 : "X-Loader"
> 0x000000080000-0x000000260000 : "U-Boot"
> 0x000000260000-0x000000280000 : "U-Boot Env"
> 0x000000280000-0x000000680000 : "Kernel"
> 0x000000680000-0x000010000000 : "File System"
> usbmon: debugfs is not available
> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
> ehci-omap ehci-omap.0: new USB bus registered, assigned bus
> number 1
> ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
> ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
> usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
> usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> usb usb1: Product: OMAP-EHCI Host Controller
> usb usb1: Manufacturer: Linux 2.6.29-omap1-07182-gc3b6e50 ehci_hcd
> usb usb1: SerialNumber: ehci-omap.0
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 3 ports detected
> Initializing USB Mass Storage driver....
> usbcore: registered new interface driver usb-storage
> USB Mass Storage support registered.
> android init
> android_bind
> mass_storage_function_add
> android_usb gadget: Number of LUNs=1
> adb_function_add
> android_usb gadget: android_usb ready
> musb_hdrc musb_hdrc: MUSB HDRC host driver
> musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 2
> usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
> usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> usb usb2: Product: MUSB HDRC host driver
> usb usb2: Manufacturer: Linux 2.6.29-omap1-07182-gc3b6e50 musb-hcd
> usb usb2: SerialNumber: musb_hdrc
> usb usb2: configuration #1 chosen from 1 choice
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 1 port detected
> twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0
> twl4030_rtc twl4030_rtc: Power up reset detected.
> twl4030_rtc twl4030_rtc: Enabling TWL4030-RTC.
> mmci-omap-hs mmci-omap-hs..0: Failed to get debounce clock
> usbcore: registered new interface driver usbhid
> usbhid: v2.6:USB HID core driver
> logger: created 64K log 'log_main'
> logger: created 256K log 'log_events'
> logger: created 64K log 'log_radio'
> TCP cubic registered
> NET: Registered protocol family 17
> NET: Registered protocol family 15
> RPC: Registered udp transport module.
> RPC: Registered tcp transport module.
> Power Management for TI OMAP3.
> VFP support v0.3: implementor 41 architecture 3 part 30
> variant c rev 1
> Console: switching to colour frame buffer device 80x30
> clock: clksel_round_rate_div: dpll4_m4_ck target_rate 36000000
> clock: new_div = 12, new_rate = 36000000
> omapdss: Could not find exact pixel clock. Requested 23500
> kHz, got 24000 kHz
> twl4030_rtc twl4030_rtc: setting system clock to 2000-01-01
> 00:00:00 UTC (946684800)
> Waiting 1sec before mounting root device...
> mmc0: new high speed SDHC card at address 0001
> mmcblk0: mmc0:0001 00000 3.79 GiB
> mmcblk0:<4>mmcblk0: retrying using single block read
>
> ---------------------------------------------------------------------------------------------------------------------------------------------------------
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> Osd mailing list
>
>
>
>
>
> --
> �� �� �� / (��)����ַ��
> Jooil Park / EEPEE Solution Co., Ltd.
> jooi...@eepeesol.com <mailto:jooi...@eepeesol.com> Mobile :
> 010-6432-8498
> ����� ���α� ����3�� 212-16,���� 1�������й븮 702ȣ (152-775)
> Tel : 82-2-2613-4881 Fax : 82-2-2613-4880 www.eepeesol.com
> <http://www.eepeesol.com>
>
--
Thanks & Regards,
Amarnath Alamuri
Associate Embedded Software Engineer,
Embedded and Wireless Services (EMBINUX group),
SQLStar International Limited(/Inc.).
Phone: +91 40 2310 1600
email address : amarnath...@embinux.com,amarn...@sqlstar.com