Skip to first unread message
funBart
Dec 18, 2013, 5:04:50 PM12/18/13
to kisslicer-r...@googlegroups.com
Newbie
- Posts: 1
Well I am very pleased to announce the first public beta release of GPX. A gcode to x3g conversion utility I have written to make it easier for Makerbot 3D printer owners to use KISSlicer as their slicer. In the past you had to load the sliced gcode into ReplicatorG or Makerware to export it, now you can install GPX and it will do the conversion in a matter of seconds as a post process from within KISSlicer
RABI>>>>>>>>>>>>>>
funbart
- Sr. Member
- Posts: 307
Hi, is it a bowden or direct drive you use?
The destring settings seem to me odd (at least very different to mine: i use a direct drive system):
destring_suck=6 (I use 0.5mm, I think a bowden system is max 2mm?, maybe check what the Ultimaker guys have set?)destring_prime=6 (same here: I use 0.5mm, I think bowden is max 2mm?)
destring_min_mm=0.5 (this is the min distance of travel for a wipe (going back over the extruded path) : I have set it to 5mm)destring_trigger_mm=0(0mm: This is always destringing with each travel, which isn't a good thing: I have set it to 5mm as well)destring_speed_mm_per_s=80 (different stories about the speed: some say it must be fast (like 80mm/s), but when destringing 6mm, as you do, it was resulting with me in 'shaved filament'. I have put it at 10mm/s)
About the distance for jump / trigger: I use only 2mm for very small objects, and 10mm for larger objects.
I hope this helps a little.
Bart
The destring settings seem to me odd (at least very different to mine: i use a direct drive system):
destring_suck=6 (I use 0.5mm, I think a bowden system is max 2mm?, maybe check what the Ultimaker guys have set?)destring_prime=6 (same here: I use 0.5mm, I think bowden is max 2mm?)
destring_min_mm=0.5 (this is the min distance of travel for a wipe (going back over the extruded path) : I have set it to 5mm)destring_trigger_mm=0(0mm: This is always destringing with each travel, which isn't a good thing: I have set it to 5mm as well)destring_speed_mm_per_s=80 (different stories about the speed: some say it must be fast (like 80mm/s), but when destringing 6mm, as you do, it was resulting with me in 'shaved filament'. I have put it at 10mm/s)
About the distance for jump / trigger: I use only 2mm for very small objects, and 10mm for larger objects.
I hope this helps a little.
Bart
Makerbot Replicator 1 dual
Minimalistic Mk8 replacement by Emmett
Sailfish Firmware
Kisslicer Pro 1.1.0 Alpha
Minimalistic Mk8 replacement by Emmett
Sailfish Firmware
Kisslicer Pro 1.1.0 Alpha
Nitewing
- Newbie
- Posts: 1
Hi,
i'm new to the whole 3d printing stuff. I started 2 month ago with Slic3r, then Cura and no Kisslicer.
Kisslicer in general works well... except the strings. It makes me nuts.
I read everything here about settings etc. but it won't work.
I raised and lowered temperature, changed the settings, activated z-lift, deactivated z-lift, changed speed etc.... printed a couple of testobjects, but i'm stuck.
Objects without spares come out pretty well, but with spares...
I love Kisslicer and i'm trying to figure out, what i'm doing wrong.
Maybe someone could help me.
I'm pretty sure i messed it up... somehow...
The result at the end is the best i was able to print (with the settings below). I hope it is possible to make it better.
(I had prints where i thought Spiderman explodet ^^)
Thank you.
Ben
My Setup:
Prusa I3
3mm PLA @ 187 Degrees Celcius
Melzi Board with Marlin
J-Head 0.35
Testobject:
http://www.thingiverse.com/thing:11846
My Kisslicer Settings:
Style:
[0% Infill Test]
layer_thickness_mm=0.2
extrusion_width_mm=0.35
num_loops=2
skin_thickness_mm=1
infill_extrusion_width=0.35
infill_density_denominator=10
stacked_layers=1
use_destring=1
use_wipe=1
loops_insideout=1
infill_st_oct_rnd=1
inset_surface_xy_mm=0.16
seam_jitter_degrees=15
seam_depth_scaler=1
Support:
[Support]
support_sheathe=0
support_density=0
support_inflate_mm=0
support_gap_mm=0.5
support_angle_deg=77
support_z_max_mm=-0.5
sheathe_z_max_mm=-1
raft_mode=0
prime_pillar_mode=0
raft_inflate_mm=3
Material:
[PLA Test]
g_code_matl=3B204D617962652073657420736F6D65206D6174657269616C2D737065636966696320472D636F64653F
fan_Z_mm=0
fan_loops_percent=50
fan_inside_percent=50
fan_cool_percent=50
temperature_C=187
keep_warm_C=140
first_layer_C=210 (is set so high beacuase when the fan starts, it drops the temperature to ~190)
bed_C=45
sec_per_C_per_C=0.00415512
flow_min_mm3_per_s=0.01
flow_max_mm3_per_s=10
destring_suck=6
destring_prime=6
destring_min_mm=0.5
destring_trigger_mm=0
destring_speed_mm_per_s=80
Z_lift_mm=0
min_layer_time_s=0
wipe_mm=2
cost_per_cm3=0
flowrate_tweak=1
fiber_dia_mm=2.85
color=0
Printer:
[Prusa i3 test]
bed_STL_filename=
extension=gcode
cost_per_hour=0
g_code_prefix=4732380A4D38330A4D31343020533C4245443E0A4D31303920533C54454D503E0A
g_code_warm=3B2035442D7374796C650A4D31303420533C54454D503E0A
g_code_cool=3B2035442D7374796C650A4D31303420533C54454D503E0A
g_code_N_layers=3B204D617962652072652D686F6D652058202620593F
g_code_postfix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
every_N_layers=0
post_process=NULL
num_extruders=1
firmware_type=1
add_comments=1
fan_on=M106
fan_off=M107
fan_pwm=1
add_m101_g10=0
z_speed_mm_per_s=100
z_settle_mm=0
bed_size_x_mm=190
bed_size_y_mm=180
bed_size_z_mm=170
bed_offset_x_mm=95
bed_offset_y_mm=85
bed_offset_z_mm=0
bed_roughness_mm=0
travel_speed_mm_per_s=120
first_layer_speed_mm_per_s=20
dmax_per_layer_mm_per_s=50
xy_accel_mm_per_s_per_s=500
lo_speed_perim_mm_per_s=15
lo_speed_solid_mm_per_s=12
lo_speed_sparse_mm_per_s=10
hi_speed_perim_mm_per_s=80
hi_speed_solid_mm_per_s=60
hi_speed_sparse_mm_per_s=20
ext_gain_1=1
ext_material_1=3
ext_axis_1=0
ext_gain_2=1
ext_material_2=0
ext_axis_2=0
ext_gain_3=1
ext_material_3=0
ext_axis_3=0
model_ext=0
support_ext=0
support_body_ext=0
raft_ext=0
solid_loop_overlap_fraction=0.5
Result:
i'm new to the whole 3d printing stuff. I started 2 month ago with Slic3r, then Cura and no Kisslicer.
Kisslicer in general works well... except the strings. It makes me nuts.
I read everything here about settings etc. but it won't work.
I raised and lowered temperature, changed the settings, activated z-lift, deactivated z-lift, changed speed etc.... printed a couple of testobjects, but i'm stuck.
Objects without spares come out pretty well, but with spares...
I love Kisslicer and i'm trying to figure out, what i'm doing wrong.
Maybe someone could help me.
I'm pretty sure i messed it up... somehow...
The result at the end is the best i was able to print (with the settings below). I hope it is possible to make it better.
(I had prints where i thought Spiderman explodet ^^)
Thank you.
Ben
My Setup:
Prusa I3
3mm PLA @ 187 Degrees Celcius
Melzi Board with Marlin
J-Head 0.35
Testobject:
http://www.thingiverse.com/thing:11846
My Kisslicer Settings:
Style:
[0% Infill Test]
layer_thickness_mm=0.2
extrusion_width_mm=0.35
num_loops=2
skin_thickness_mm=1
infill_extrusion_width=0.35
infill_density_denominator=10
stacked_layers=1
use_destring=1
use_wipe=1
loops_insideout=1
infill_st_oct_rnd=1
inset_surface_xy_mm=0.16
seam_jitter_degrees=15
seam_depth_scaler=1
Support:
[Support]
support_sheathe=0
support_density=0
support_inflate_mm=0
support_gap_mm=0.5
support_angle_deg=77
support_z_max_mm=-0.5
sheathe_z_max_mm=-1
raft_mode=0
prime_pillar_mode=0
raft_inflate_mm=3
Material:
[PLA Test]
g_code_matl=3B204D617962652073657420736F6D65206D6174657269616C2D737065636966696320472D636F64653F
fan_Z_mm=0
fan_loops_percent=50
fan_inside_percent=50
fan_cool_percent=50
temperature_C=187
keep_warm_C=140
first_layer_C=210 (is set so high beacuase when the fan starts, it drops the temperature to ~190)
bed_C=45
sec_per_C_per_C=0.00415512
flow_min_mm3_per_s=0.01
flow_max_mm3_per_s=10
destring_suck=6
destring_prime=6
destring_min_mm=0.5
destring_trigger_mm=0
destring_speed_mm_per_s=80
Z_lift_mm=0
min_layer_time_s=0
wipe_mm=2
cost_per_cm3=0
flowrate_tweak=1
fiber_dia_mm=2.85
color=0
Printer:
[Prusa i3 test]
bed_STL_filename=
extension=gcode
cost_per_hour=0
g_code_prefix=4732380A4D38330A4D31343020533C4245443E0A4D31303920533C54454D503E0A
g_code_warm=3B2035442D7374796C650A4D31303420533C54454D503E0A
g_code_cool=3B2035442D7374796C650A4D31303420533C54454D503E0A
g_code_N_layers=3B204D617962652072652D686F6D652058202620593F
g_code_postfix=3B202D2D3D3D20456E64205265666572656E6365203D3D2D2D0A4D3130342053302020202020202020202020202020202020202020203B657874727564657220686561746572206F66660A4D3134302053302020202020202020202020202020202020202020203B6865617465642062656420686561746572206F66662028696620796F752068617665206974290A4739312020202020202020202020202020202020202020202020202020202020202020202020203B72656C617469766520706F736974696F6E696E670A473120452D312046333030202020202020202020202020202020202020202020202020202020203B72657472616374207468652066696C616D656E74206120626974206265666F7265206C696674696E6720746865206E6F7A7A6C652C20746F2072656C6561736520736F6D65206F66207468652070726573737572650A4731205A2B302E3520452D3520582D323020592D323020467B74726176656C5F73706565647D203B6D6F7665205A20757020612062697420616E6420726574726163742066696C616D656E74206576656E206D6F72650A4732382058302059302020202020202020202020202020202020202020202020202020202020203B6D6F766520582F5920746F206D696E20656E6473746F70732C20736F207468652068656164206973206F7574206F6620746865207761790A4D3834202020202020202020202020202020202020202020202020203B7374657070657273206F66660A473930202020202020202020202020202020202020202020202020203B6162736F6C75746520706F736974696F6E696E670A
every_N_layers=0
post_process=NULL
num_extruders=1
firmware_type=1
add_comments=1
fan_on=M106
fan_off=M107
fan_pwm=1
add_m101_g10=0
z_speed_mm_per_s=100
z_settle_mm=0
bed_size_x_mm=190
bed_size_y_mm=180
bed_size_z_mm=170
bed_offset_x_mm=95
bed_offset_y_mm=85
bed_offset_z_mm=0
bed_roughness_mm=0
travel_speed_mm_per_s=120
first_layer_speed_mm_per_s=20
dmax_per_layer_mm_per_s=50
xy_accel_mm_per_s_per_s=500
lo_speed_perim_mm_per_s=15
lo_speed_solid_mm_per_s=12
lo_speed_sparse_mm_per_s=10
hi_speed_perim_mm_per_s=80
hi_speed_solid_mm_per_s=60
hi_speed_sparse_mm_per_s=20
ext_gain_1=1
ext_material_1=3
ext_axis_1=0
ext_gain_2=1
ext_material_2=0
ext_axis_2=0
ext_gain_3=1
ext_material_3=0
ext_axis_3=0
model_ext=0
support_ext=0
support_body_ext=0
raft_ext=0
solid_loop_overlap_fraction=0.5
Result:
Reply all
Reply to author
Forward
This conversation is locked
You cannot reply and perform actions on locked conversations.
0 new messages